MDB ubabub Nifty U0310 User manual

Timber Crib
Product Code: U0310
Nifty
revised 260813

Nifty
Domestic child crib
Wood model
Instruction manual
Congratulations and
thank you for purchasing
an Ubabub product.
With our entire line of
clearly modern nursery
furniture, we are developing
cribs that have the capacity
to convert into a junior
bed and adapt with your
growing child. During the
design and production
of this product we have
selected materials that are
either recyclable or derived
from sustainable practices.
2
PERSONS REQUIRED ASSEMBLY TIME
TOOLS REQUIRED
– PHILLIPS HEAD SCREWDRIVER
– ALLEN KEY (SUPPLIED)
Contents
Contents & Hardware 3
Warning, Care & Maintenance 4
AFoot panel position 8
B Side panel position 9
CEnd panel assembly 10
DMattress base position 11
EBaseplate assembly 12
FFinished assembly 13

Contents
3
Contents
Contents & Hardware 3
Warning, Care & Maintenance 4
AFoot panel position 8
B Side panel position 9
CEnd panel assembly 10
DMattress base position 11
EBaseplate assembly 12
FFinished assembly 13
2 x End Panels 2 x Lower Rails
1 x Base2 x Side Panel
Hardware
1 x Allen Key I
28 x 15mm
Bolt
4 x Support
Plate
4 x Support
Pin
12 x Locking
Cam
12 x Connector
Pin
8 x 55mm
bolt
1 x Allen Key II
4 x 60mm
bolt

4
WARNING:
Failure to follow these warnings and
the assembly instructions could result
in serious injury or death.
WARNING:
Parents should ensure a safe environment for the
child by checking regularly, before placing the
child in the product, that every component is
properly and securely in place.
Please do NOT remove any wood screws
in the normal disassembly of the crib.
WARNING:
CAUTION:ANYMATTRESSUSEDINTHISCRIB
MUST BE AT LEAST 27 1/4 INCHES (69CM)
BY 51 5/8 INCHES (131CM) WITH A THICK-
NESS NOT EXCEEDING 6 INCHES (15CM).
Please read the Caution and Warning
Statements insert before using your crib.
READ ALL INSTRUCTIONS BEFORE ASSEMBLING
CRIB . KEEP THE MANUAL FOR FUTURE USE.

5
Infants can suffocate on soft bedding. Never add a pillow or comforter. Never
place additional padding under an infant.
•
To reduce the risk of SIDS, pediatricians recommend healthy infants be placed•
on their backs to sleep, unless otherwise advised by your physician.
Strings can cause strangulation! Do not place items with a string around a•
child’s neck, such as hood strings or cords. Do not place cords, straps,
or similar items that could become wound around the child’s neck in or near this
crib. Do not suspend strings over a crib or attach strings to toys.
To help prevent strangulation tighten all fasteners. A child can trap parts of the•
body or clothing on loose fasteners.
DO NOT place a crib near a window where cords from blinds or drapes may•
strangle a child. Do not place this crib near a window or a patio door where a
child could reach the cord of a blind or curtain and be strangled.
When a child is able to pull to a standing position, set the mattress to the lowest•
position and remove bumper pads, large toys and other objects that could serve
as steps for climbing out.
•
• Check this product for damaged hardware, loose joints, loose bolts or other
fasteners, missing parts or sharp edges before and after assembly and frequently
during use. Securely tighten loose bolts and other fasteners. DO NOT use crib if
any parts are missing, damaged or broken. DO NOT substitute parts. Contact
MDB FAMILY for replacement parts and instructional literature if needed.
DO NOT use a water mattress with this crib.•
If use a non-toxic for children’s products.•
Never use plastic shipping bags or other plastic
as mattress covers •
because they can cause suffocation.
Infants can suffocate in gaps between crib sides when used with a mattress•
that is too small.
• Follow warnings on all products in a crib.
Do not use this crib if the child is able to climb out unaided or is taller than
35 in. (89cm).
• Do not use this crib if you cannot exactly follow the accompanying instructions.
• The mattress used with this crib should not be more than 15cm thick and should
be of such length with width that the gap between the mattress and the sides of the
crib is no more than 3cm when the mattress is pushed into the corner of the crib.

6
Please refer to the label (sample below) on the inside face
of the headboard. Record the model/ item number and serial
number of your crib, the name of the store where you made
the purchase, the date of purchase and the wood finish in
the box to the lower right.
WE WILL ASK YOU FOR YOUR SERIAL NUMBER FOR ALL
WARRANTY AND REPLACEMENT PART REQUESTS. PLEASE
REFER TO THE LAST PAGE OF THIS INSTRUCTION SHEET FOR
WARRANTY INFORMATION. KEEP THIS MANUAL FOR FUTURE
REFERENCE.
THIS PRODUCT CONFORMS TO THE
APPLICABLE REGULATIONS OF THE
CONSUMER PRODUCTS SAFETY COMMISSION.
www.themdbfamily.com
CAUTION: ANY MATTRESS USED IN THIS CRIB
MUST BE AT LEAST 27 1/4 INCHES (69CM) BY
51 5/8 INCHES (131CM) WITH A THICKNESS
NOT EXCEEDING 6 INCHES (15CM).
SAMPLE LABEL
Storage:
Care and Cleaning:
• Solid woods exchange moisture with the air adjusting to major
changes in room temperature and humidity. Therefore, it is
best to place your furniture away from heating or air-
conditioning vents.
• Sunlight is not friendly to solid wood furniture and prolonged
direct exposure to harsh sunlight can discolor the nish. Be
careful not to place your furniture in direct sunlight for
extended periods of time. As with all your ne furniture, blot up
spills immediately.
• Do not scratch or chip the nish. Do not use abrasive chemicals
for cleaning. Clean with mild soap on a soft rag. Rinse and dry
thoroughly. If you ever renish this furniture, be sure to use only
a non-toxic nish specied for children’s products. If you choose
to renish this furniture, the warranty will be voided.

7
IF YOU WOULD LIKE TO ORDER
REPLACEMENT OR MISSING PARTS
PLEASE VISIT US AT:
WWW.THEMDBFAMILY.COM
OR YOU CAN CONTACT US BY MAIL:
MDB FAMILY
855 WASHINGTON BLVD.
MONTEBELLO, CA 90640
We will replace any missing parts at the time
of purchase or any defective item within
a one year period from the date of original
purchase. Please keep your receipt so that
we may process your warranty request. This
warranty only covers new units with original
packaging and ownership, and is not trans-
ferable. It does not cover any used, second-
hand or demo models.
This warranty does not cover any damaged
or defective parts that result from installation
and assembly, normal wear and tear, abuse,
negligence, improper use or alteration to the
nish, design, and hardware. The specic
legal rights of this warranty may vary from
state to state. Some states do not allow any
exclusion or limitation of incidental damages.
Some states do not allow limitation on how
long an implied warranty lasts.
ONE YEAR LIMITED WARRANTY:
Registering your product is even easier than
before. You can register your product on our
website at: www.themdbfamily.com

AFoot panel position
8
Step 1 Clear floor space.
Step 2 Lay Nifty end on the ground screw holes facing up. Using screw driver insert
Connecting Pins to the six points as per diagram.
Step 3 Insert Support Pins, next to single connecting pin at top of the End Panel .
Step 4 Repeat on other end.
Step 5 Place the end with Connecting Pins up on a carpeted surface or blanket
to protect the end.
Step 6 Insert lower rails (with legs) onto Connecting Pins. Ensure the holes for
the Locking Cams are facing towards the inside of the crib, align the
corresponding dots
(see Fig.01).
Step 7 Insert Locking Cams on both lower rails.
Step 8 Align the Locking Cams and connecting pins. Insert the connecting pins to
the lower rails. Make sure connecting pins are passing through the Locking
Cams. Insert the Locking Cam nuts. Use screwdriver to turn Locking Cam
nuts clockwise until tight. (see Fig.02).
Fig. 02
Fig. 01
Align corresponding
dots at each end of
all components.
Insert the
Locking Cam
nut.
Use screwdriver to turn Locking
Cam nuts clockwise until tight.
2.1
2.2
2.3
Insert the
connecting pins
to the rails.

BSide panel position
9
Step 1 Select a Side Panel.
Step 2 Side Panel will slide snugly onto the Connecting & Support Pins.
Step 3 Insert Locking Cams on both side panels. (see Fig. 03).
Step 4 Align the Locking Cams and connecting pins. Insert the connecting pins
to the side panels. Make sure connecting pins are passing through the
Locking Cams. Insert the Locking Cam nuts. Use screwdriver to turn
Locking Cam nuts clockwise until tight. (see Fig. 03).
Step 5 Repeat steps 3 & 4 for other Side Panel.
Step 6 Insert 8 bolts into Lower Rail, attach rail into Side Panel (see Fig. 04).
(Turn clockwise using Allen Key I until tight).
Use screwdriver to turn Locking
Cam nuts clockwise until tight.
Fig. 04
Fig. 03
Insert the
Locking Cam
nut.
x 4
3.1
3.2
3.3
Insert the
connecting pins
to the rails.
8 x
55mm
bolt

CEnd panel assembly
10
Fig. 05
Insert the
Locking Cam
nut.
Use screwdriver to turn Locking
Cam nuts clockwise until tight.
5.1
5.2
5.3
Insert the
connecting pins
to the rails.
x 6
Step 1 Take the remaining End Panel.
Step 2
Step 3 Insert Locking Cams on both side panels and lower rails. (see Fig. 05).
Step 4 Align the Locking Cams and connecting pins. Insert the connecting pins
to the side panels and lower rails. Make sure connecting pins are passing
through the Locking Cams. Insert the Locking Cam nuts. Use screwdriver
to turn Locking Cam nuts clockwise until tight. (see Fig. 05).
Install the End Panel, align all Connecting & Support Pins before applying
any pressure to panel. (See main diagram below).

DMattress base position
Step 1 Select the Base.
Step 2 Install Base from the underside of the crib until it lines up with the captive
nuts. Select mattress base position for your baby. As your baby grows, it is
important to lower the mattress base.
Step 3 Insert bolts through base and into captive nuts (see Fig. 06).
Step 4 Tighten using Allen Key II.
11
Change to lower
positions when
children are able to
sit up or pull to a
standing position.
2 Upper positions are
suitable for newborns or
children before they are
able to push up on hands
and knees.
Fig. 06
Side Elevation
4 x
60mm
bolt

Step 1 Select an L-shaped base plate and seven bolts.
Step 2 Install a base plate onto one the corners where the leg rails
meet the end panels as per diagram.
Step 3 Using a screwdriver install the seven bolts into the pre-drilled holes
securing the base plate to both the end panel and leg rails.
Step 4 Repeat steps 2 to 4 on each of the corners.
EBaseplate assembly
12
15mm
bolts
Support
plate
x 4
x 28
x 4

FFinished assembly
Step 1 Check all Locking Cams and bolts for tension, adjust tension if required.
Step 2 Using two adults, carefully position crib onto its legs.
Step 3 Clean all surfaces prior to use.
Step 4 Install the mattress into your completed NIFTY crib.
13

14
KEEP THIS MANUAL IN A SAFE PLACE FOR
FUTURE REFERENCE.
Recheck all screws and bolts to be sure they are
fastened securely. Do not overtighten.
Before using your crib, please read all cautionary
statements on the insert sheet.
Junior Bed Conversion Kit is not included,
sold separately. Please contact your retailer to
purchase.

15
Made in China

INSTRUCCIONES
revisado 260813
Nifty
Cuna Timber
Código de producto: U0310

Nifty
Cuna doméstica para niños
Modelo madera
Manual de instrucciones
Permítanos extenderle
una felicitación y nuestro
agradecimiento por adquirir
un producto Ubabub.
Al igual que en toda
nuestra moderna línea de
muebles para la habitación
de su bebé, durante el
diseño y producción de
este producto hemos
seleccionado materiales
reciclables o producidos
mediante un proceso
sostenible.
18
PERSONS REQUIRED ASSEMBLY TIME
HERRAMIENTAS REQUERIDAS
– DESTORNILLADOR TIPO PHILLIPS
– LLAVE ALLEN (INCLUIDA)

19
Herramientas
Contenido
2 paneles posteriores 2 barandillas inferiores
1 base2 paneles laterales
1 llave allen I
28 tornillos de
15 mm
4 placas de
soporte
4 pines de
soporte
12 válvulas
de cierre
12 pines de
conexión
8 tornillos de
55 mm
1 llave allen II
4 tornillos de
60 mm

20
PRECAUCIÓN: TODO COLCHÓN QUE SE USE
EN ESTE CUNA DEBE MEDIR AL MENOS 69
CM. (27 1/4 PULGADAS) POR 131 CM. (51 5/8
PULGADAS) Y TENER UN GROSOR MÁXIMO
DE 15 CM. (6 PULGADAS).
Lea las advertencias y precauciones
antes de usar la cuna.
De no seguir estas advertencias
e instrucciones de ensamblaje,
se pueden ocasionar lesiones
graves o incluso la muerte.
ADVERTENCIA:
LEA TODAS LAS INSTRUCCIONES ANTES DE
ENSAMBLAR LA CUNA. GUARDE ESTE
MANUAL PARA CONSULTARLO EN EL FUTURO.
Los padres deben asegurarse de que la cuna
es segura para el niño al vericar de forma
regular, antes de colocar al niño en la cuna,
que todas sus piezas estén ensambladas en
su lugar correcto y de forma segura.
ADVERTENCIA:
ADVERTENCIA:
NO QUITE LOS TORNILLOS DE MADERA AL
DESARMAR LA CUNA DE FORMA NORMAL.