Mecam DM07 User manual

1

2
FCC Compliance Statement
This device complies with Part 15 of the FCC Rules. Operation is
subjected to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept
any interference received, including interference that may
cause undesired operation. SAR test distance is 0mm.
This equipment has been tested and found to comply with
limits for a Class B digital device, pursuant to Part 15 of the FCC
rules. The equipment complies with FCC RF exposure limits set
forth for an uncontrolled environment.
These limits are designed to provide reasonable protection
against harmful interference in residential installations. This
equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause interference to radio or television
equipment reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Move the equipment away from the receiver.
-Plug the equipment into an outlet on a circuit different from
that to which the receiver is connected.
-Consult the dealer or an experienced radio/television
technician for additional suggestions.
You are cautioned that any change or modifications to the
equipment not expressly approved by the party responsible for
compliance could void your authority to operate such
equipment.

3
Safety Instructions
•Do not drop, puncture or disassemble the device; otherwise
the warranty will be voided.
•Avoid all contact with water. Dry your hands before using
the device.
•Use the device with care. Avoid pressing hard on the device
body.
•For your own safety, avoid using the device when there is a
storm or lightning.
•Use only the accessories supplied by the manufacturer.
•Keep the device out of the reach of infants.
•Do not leave the device on the dashboard where it is subject
to direct sunlight.
•The battery is integrated with the device. Do not dissemble
and modify. The battery should be replaced by an
authorized service center only.

4
Introduction
MeCam is hands-free wearable camera that you can pin or clip
it to your shirt, wear it as a necklace, or mount it to the car
windshield to record high quality videos and pictures.
Package Content
The following items come with your package.
Camera USB Cable Car Adapter (Optional)
Strap Clip Pin Clip
Stand Suction Cup Bracket
(Optional)

5
Product Overview
Function button
Power button
Wi-Fi LED
Function LED
Power LED
Micro SD card slot
Micro USB port
HDMI port
Microphone

6
Buttons and LED Indicators
Button Functions
Status Action
Power on Press and hold the Power button for 2 seconds.
Power off Press and hold the Power button for 3 seconds.
Turn off Wi-Fi Press and hold the Power button for 6 seconds.
Start recording Press and hold the Function button for 3 seconds.
Stop recording While recording, press and hold the Function
button for 3 seconds.
Take photo Press the Function button.
Reset to default Press and hold the Function button for 10
seconds.
Reboot Press and hold the Power button for 10 seconds.
LED Indicators
Status Power LED Wi-Fi LED Function LED
Power on Light Green Light Green Off
Start recording Light Green Light Green Blink Green
Wi-Fi off Light Green Off Off
Power off Off Off Off
Battery is charging Off Off Light Red
Charging complete Off Off Off
Low battery Blink Red Off Off

7
Getting Started
Inserting the Memory Card
Insert the memory card with the gold
contacts facing to the front of the device.
Push the memory card until it clicks into
place.
About SD Card
•Please use SD card with the size/memory at least 8GB, Class
10 (up to 64GB).
•Be sure to format SD card using the device before the initial
usage.
•Do not remove the memory card while recording. This may
damage the memory card.
Charging the Battery
1. Connect one end of the USB cable to the micro USB port of
the device.
2. Connect the other
end of the USB cable
to the computer.

8
Note
•As an alternative, you can also charge the device using an AC
adapter.
Powering the Device On/Off
•To turn on the power, press and hold
the Power button for 2 seconds.
•To turn off the power, press and hold
the Power button for 3 seconds.

9
Connecting to Your Smartphone
List of Supported Smartphone
•iOS device: iOS 6.1 or above
•Android device: Android 4.0 or above
Install MeCam HD APP
1. Make sure your smartphone is connected to the Internet.
2. Launch App Store (iOS)or Google Play/Play Store (Android)
application.
3. On the search bar, enter the keyword “MeCamHD” to search
for APP.
4. Download and install MeCam HD. After the installation is
complete, the MeCam icon ( ) is displayed on the
application screen.
Note
•When you use a code reader application to scan the
respective QR code below, your smartphone will show a
direct link to download MeCam HD.
(iOS) (Android)
•The application UI varies depending on the device operating
system and design.

10
Connect via Wi-Fi
1. On your smartphone, launch Settings application.
2. In WIRELESS & NETWORKS, tap
Wi-Fi and set it to ON.
The available networks are listed.
3. Tap MeCamHD to connect to the
camera.
4. Enter the password and tap Join
(iOS) or Connect (Android).
Note
•The default password is “Enjoylife”.
•You can change the SSID and password in Setup mode.

11
Controlling the Device using APP
Preview Mode
1. Tap Preview tab to switch to Preview/Record mode.
2. Tap to view the live view on your smartphone.
Record Mode
Capture Photos
Select ONE SHOT ( )to switch to Photo mode.
Tap to capture a photo.
Note
•You can also press the Function button on the camera to
capture a photo.

12
Capture Continuous Shots
Select PHOTO BURST ( )to switch
to Continuous Shot mode. Tap and
hold to continuously capture
photos.
Release to stop shooting.
Capture Photos By Time Lapse
Select TIME LAPSE ( )to switch to
Time Lapse mode.
Tap to continuously capture
photos at the preset interval time.
Tap to stop shooting.

13
Record Videos
Select RECORD VIDEO ( )to switch
to Video mode.
Tap to start recording.
To stop recording, tap .
Note
•You can also press the Function
button on the camera to
start/stop recording video.
Snap Movie
Select SNAP MOVIE ()to switch
to Snap Movie mode.
Tap to start recording a
15-second video clip.
Tap and hold to continuously
record the video. Release it to pause
the recording.
To manually stop recording, tap
Finish.

14
Playback Mode
Tap Playback tab to switch to
Playback mode. Tap Video or Photo
tab to browse the recorded files.
Play Video
1. On Video list, tap the desired
video to play the video.
2. Tap the screen to pause the
playback. Tap the screen again to
resume the video playback.
View Photo
On Photo list, tap the desired photo that you want to view.
Delete Files
On the playback screen, tap to
delete the current file.
A confirmation message appears on
the screen, then tap Delete to
confirm file deletion.

15
Download File into Your Smartphone
On the playback screen, tap > and then select the video
resolution to save the selected video into your smartphone.
The downloaded files are listed in the Mobile list.
(for video only)
Note
•You do not need to specify the photo size before saving it
into the smartphone.

16
Sharing Files
Before sharing the file to Facebook
or YouTube, download the desired
file first into your smartphone.
1. Disconnect the Wi-Fi connection
between the device and your
smartphone. Then connect your
smartphone to the Internet
(either by mobile data connection
or Wi-Fi).
2. Launch MeCam HD application.
3. Tap > Sign in > +>
Facebook ( ) or YouTube ( ).
Follow the on-screen instructions
to login to your social network
account. Tap Finish when the
settings are complete.
4. Tap Playback tab and select file
that you want to share from the
Mobile list.
5. Tap and select Facebook ( )
or YouTube ( ) to share the file.

17
Configuring Settings
Configure the video and photo
recording, wireless connection, and
the device general settings.
1. Tap Settings tab to switch to Setup
mode.
2. Select the desired menu option.
3. Tap to select the desired setting.
Menu Option Description
Video
Resolution
Set the video resolution.
Available options: 1920x1080 30f /
1280x720 60f / 432x240 120f
Photo Burst
Frequency
Specify the number of continuous shots per
second.
Available options: 5p1s / 10p1s / 30p1s
Time Lapse
Frequency
Select the interval options when capturing
photos using Lapse mode.
Available options: 1p2s / 1p30s / 1pm
Stabilization Select ON to enable the stabilizer function.
Available options: ON / OFF

18
Menu Option Description
Wifi Setting Configure the SSID and password settings.
Enter the new SSID and password. Then tap
OK to save the settings.
Date/Time
Setting
View the current date and time.
Note
•The data shown is based on your
smartphone’s date and time settings.
Date/Time
Stamp Overlay
Select ON to include a date and time on a
video stream.
Available options: ON / OFF
Format SD card Select OK to format the memory card
installed on the device.

CAUTION:
Formatting is typically irreversible, so be
sure to transfer the recorded files to your PC
first before formatting the SD card.
Version
Information
View the model name and firmware
version.
Factory Default Select OK to reset all settings to factory
default settings.

19
Using Accessories
Using the Strap
To use the strap, do the following:
1. Press the quick release buckle to detach
the lanyard clip.
2. Insert the lanyard through the strap
eyelet on the bracket. Make a loop to
secure it.
3. Install the camera into the bracket.
4. Attach the quick release buckle onto
its slot (see Step 1 illustration).
Press the buckle firmly until it snaps
into place.
5. Wear the strap.

20
Using the Clip
To wear the device on your cloth using the clip, do the
following:
1. Install the camera into the bracket.
2. Pinch the prongs to open the
clipper and wear it on your cloth.
Using the Pin Clip
To wear the device on your cloth using the pin clip, do the
following:
1. Install the camera into the
bracket.