MEEPO NLS 3 User manual

MANUAL
@MEEPOBOARD | WWW.MEEPOBOARD.COM MEEPO NLS 3

COMMUTE IN STYLE

READ THE MANUAL CAREFULLY
BEFORE YOU RIDE
This can occur due to radio interference, a malfunctioning
battery, downhill overcharging of the battery, or other
factors. Only ride your Meepo board at speeds and on hills
where you don’t have to depend on brakes and acceleration.
YOUR BOARD MAY LOSE POWER AND BRAKES
Always be aware of your surroundings when riding in the pres-
ence of vehicles. Ride cautiously and assume the vehicles
can’t see you. Remember that your board may lose power and
brakes at any moment. Whenever you are riding, please be
aware of the laws that govern the use of your board on public
roads, bike paths, sidewalks, or other places that you may ride.
CARS AND OTHER VEHICLES CAN INJURE YOU
Additional safety gear, like gloves, pads, and long sleeves, are
highly recommended.
ALWAYS WEAR A HELMET
Crashes in these conditions may cause serious injury. Be extra
careful when pushing the limits of the board, even if you’ re an
experienced rider.
HILLS AND HIGH SPEEDS CAN BE VERY DANGEROUS
Regenerative braking may overcharge the battery. To prevent
this from happening, the remote will warn you by beeping, and
disable your braking power. Safely come to a stop before this
happens, and ride on flat surfaces or uphill to drain the battery
before attempting to ride downhill again.
BRAKING DOWNHILL WITH A FULL BATTERY WILL
CAUSE THE BOARD TO SHUT DOWN
Which means the board can accelerate aggressively ,causing
you to fall off. Try to start by moving slowly in these modes to
ensure safety.
WARNING! IN EXPERT AND PRO MODE THE THROTTLE
IS EXTREMELY SENSITIVE

MEEPO NLS 3 1
Press the power button once to start the board.
Type-c
Charging Port
5V/2A
Power Button
Speed Meter
Current gear Trip Distanceay
Forward
Odometer
Acceleration
Brake
Press “POWER" 2s to turn ON/OFF
Press “POWER" 5s for PAIRING
Press once to change model;
Press twice to switch directions;
Press three times to change KM/MPH.
Function Button
Remote Battery
Skateboard Battery
MOTORS
Rear Wheels
Front Wheels
Rear Truck
Front Truck
On/Off Switch
ESC
Battery Case
Skateboard Deck
Board Charging Port
Battery Display
Battery Display Wake Up
N5s Remote 2
R B
0mph
T:
④0: 0.0ml
0.0ml
1：How to use N5s remote?

3
Pairing The Remote And Board
5S
BOARD TYPE
9028 9005
Press “Power" for 5S to enter pairing mode.
Select the corresponding parameters shown in the diagram.
The main menu will appear when the remote and board are
successfully paired.
1
2
3
MOTOR MODE
4240 YNT90
Belt Version:4240
2
REMOTE PAIRING...
Searching
3
REMOTE PAIRED OK ！
Remote Paired OK!
4
UNIT SYSTEM
KM/H KM MPH MILE
Choose "MPH/KMH"
5
WHEEL DIAMETER
9089 91
Choose "Diameter"
6
DRIVE RATIO
2.12.0 2.2
7
76 8
8
R B
0mph
T:
④0: 0.0ml
0.0ml
Enter main menu
9
BOARD TYPE
9028 9005
Choose "9028"
Make sure the remote and skateboard are both turned off.
During pairing, roll the scroll wheel to choose parameters, press "Power" to confirm.
Attention:
Belt Version: 2.1 Belt Version: 7
7S
Press the power button for 7s, until the power
light is blinking. ESC enters pairing mode.
MOTOR POLE PAIRS
√
R B
0mph
T:
④0: 0.0ml
0.0ml
SETTINGS(1/3)
1 WHEEL-D:90
2 D/R:2.1
3 G1 SPEED:20
4 G2 SPEED:30
SETTINGS(1/3)
1 WHEEL-D:90
2 D/R:2.1
3 G1 SPEED:20
4 G2 SPEED:35
SETTINGS(2/3)
5 G3 SPEED:45
6 G4 SPEED:60
7 EBS:100
8 DIRECTION:CW
SETTINGS(3/3)
9 RESET
3：How to customize parameter settings?
2：How to preview the current setting?
Brake
Wheel Size
Gear Ratio
Gear 1:Speed Limiting
Gear 2:Speed Limiting
Gear 3:Speed Limiting
Gear 4:Speed Limiting
Limit of Braking Ratio
Change Wheel Direction
(Front & Rear)
Factory Reset
Press reverse to brake；Quickly press the power button three times to customize settings.
means "Confirm" means "Return" means "turn page"
Brake
E-SKATEBOARD(1/1)
1 BOARD PYTE:9028
2 MOTOR PYTE:4240
3 WHEEL-D:90
4 D/R:2.1
5 POLE PAIRS:7
6 VOLTAGE:50.4V
Press reverse to brake；Quickly press the power button twice times to preview the setting.
means "turn page"
E-SKATEBOARD(1/2)
1 G1 SPEED:15
ACCELERATE:30
BREAC:80
2 G2 SPEED:30
ACCELERATE:50
BREAC:80
E-SKATEBOARD(1/3)
3 G3 SPEED:45
ACCELERATE:100
BREAC:80
4 G4 SPEED:62
ACCELERATE:100
BREAC:80

4
Check the Board Battery Life on the Remote
5
Charge the Remote
6
Charge the Board
Charging Port
Charging Port
Theremote takes several hours tocharge.
If the board and remote arecharging at
the same time, the remote should finish
charging before the board.
Warning: Never leaveyourboard unattended while charging.
7
Riding Basics
ARE YOU A “REGULAR” OR “GOOFY” FOOTED RIDER?
Typically, ifyoukick a ball with your right foot, you are a regularfooted
rider. However, this is not alwaysthe case! Try both stances to see what
feels best. If youdon’t know whichto choose, one advantage of riding
goofy footed is that you have a better view of the traffic.
Regular Goofy
R B
0mph
T:
④0: 0.0ml
0.0ml

8
Change Ride Mode
The board is set in beginner mode by default. Before switching modes,
make sure you have mastered the beginner mode.
1:Limited acceleration.(7mph)
2:Moderate acceleration.(15mph)
3:High acceleration.(25mph)
4:Max acceleration.(32mph)
WARNING: The throttlewheel is much more sensitive inHI and PRO
modes. To avoid getting thrown off from the board, follow these tips:
• Start by moving forward slowly.
• Move the throttle wheel in small increments.
• Keep a wide stance on the board.
• Keep a low center of gravity.
• Lean forward when accelerating.
• Lean backward when braking.
It usually takes the remote several hours to get fully charged. Ifthe board
and remote are charging at the sametime, the remotewill be charged
first.
CYCLE THROUGH SPEED MODES:
Press the function-button once to
change speed modes.
9
Get Ready to Ride
Downhill
Grates/Drains
Poor Visibility
Uphill
Tracks
Obstacles
Water
Larger Rocks
Night Riding
Gravel
Cracks
Traffic
Always wear a helmet.
Find a flat, paved area with no obstacles for your first ride.
Read and understand the entire manual.
For more details, check out our website: www.meepoboard.com.
Other protective equipment is highly recommended.
AVOID THESE OBJECTS AS THEY CAN MAKE YOU LOSE
CONTROL OR CRASH:
Your Meepoboard hasa lot of power. Follow these tipsto ensure a safe
riding experience:
STANCE
Move the throttle wheel in small increments.
Keep a wide stance on the board.
Keep a low center of gravity.
Lean forward when accelerating.
Lean backward when braking.
BOARD TYPE
9028 9005

To insert a new battery pack, align the grooves on both ends ofthe
connector (board & battery pack).
Insert, connect, and adjust the twoends of the connector together. Make
sure to tighten the connector to make a good seal.
Ensure the connectorlaysflat within the accessory wire and thegroove
of the board.
Replaceand tighten the boltswith the hex wrench, and put thegrip tape
back on.
1010
Replace the Battery Pack
11
More Information Online
This manual is a quick start guide intended for someone with little experience
in riding electric skateboards. If you want to learn more on how to start riding,
superior riding skills, and solutions for riding problems, please visit our website:
www.meepoboard.com or send us an email at [email protected].
GETTING STARTED
How to stand on the board
How to turn
How to find a good spot to practice
ADVANCED TECHNIQUES
How to footbrake
How to ride uphill and downhill safely
What to look for when riding through traffic
MAINTENANCE
Pre-ride inspection
Routine maintenance
WARNING!
Whenever riding a electric skateboard, make safety your top priority.
Loss of control, collisions, and falls may cause serious injury to you.
Please ride responsibly and respect those around you. How you ride will
determine how people view this new mode of transportation.
WARNING: AVOID WATER!
WARNING: PINCHPOINTS
WARNING: RISK OFELECTRIC SHOCK!
WARNING:
WARNING:
Always wear a helmet when riding. Never ridein the rain, or on wet,
slippery or uneven surfaces with steep hills, traffic, cracks, traintracks,
gravel, rocks or any obstacles that could cause a loss of traction. Avoid
night riding in areas with poor visibility or narrow spaces.
WARNING:
Riding in wet conditions or through puddles can
damage the board’s electronics and cause the board
to lose power or stop suddenly. Damage to the board
due to water exposure is not covered under the
warranty.
Keep fingers, hair, and clothing away from motors,
wheels, and all moving parts.
Do not open or tamper the case or battery with
cleaning products, this will void the board’s warranty.
This equipment has been tested and complies with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules.
These limits are designedto provide reasonable protection against harmful
interferenceina residential installation. This equipment generates, uses, and
radiatesradio frequency energy. If not installed and used in accordancewith
the instructions, it maycause harmful interference to radiocommunications.
However, there is noguarantee that interferencewill not occurina particular
installation.

PRODUCT SPECIFICATIONS
BATTERY SAFETY AND HANDLING INFORMATION
Risk of explosion if battery is replaced by an incorrect type.
Disposeofused batteries according to instructions.
Failure to follow these safety instructions could result in fire,
electric shock, or other injury or damage to the Meepo Hurricane
skateboard and Meepo M5S remote or other property.
Do not attempt to disassemble the product without
consultingMeepo. Shouldyour unitneed service, contactour
Customer Service by sending an email to [email protected].
If this equipment doesradiate harmful interference to radio or television
reception, fix the problem by trying one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a different circuit from
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Prolonged exposure to sunlight may discolor or weaken theplastic cases, as
they are not UV Rated.
MEEPO Envy Skateboard: Rated Input: DC 50.4V 4.5A
N5S Remote:Rated Input: 5Vdc, 500-1000mA Operating
Temperature: 0-40°C, 10-90% RH
The board specifications were obtained under perfect conditions. Each
customer will havedifferent conditions that will make the eboard perfor-
mance fluctuate from the data we present.
CAUTION
CAUTION
IMPORTANT SAFETY AND HANDLING INFORMATION
Changes or modifications totheskateboard unapproved by Meepomayvoid
the user’s warranty.
This product is intended to be equipped only with Meepo Hurricane batteries.
Do not drop or throw the battery.
Keep the battery away from kids.
Never expose this product or the battery to any liquids.
Never throw the battery into a fire, it could cause the battery to explode.
Never bring the connector terminalsincontact withanother metal object, it
will short-circuit thebattery. Short-circuit could cause personal injury, fires or
damage to the battery.
Your device contains an internal rechargeablelithium-ion battery which may
present a risk of fire or chemical burn ifmistreated. Do not charge or use the
unit in a car or places where the temperature surpasses 40°C.
Thecharger supplied with the electric skateboard
should be regularly examined for damage tothe
cord, plug, enclosure, and other parts. Inthe event
of such damage, the skateboard must not be
charged until the charger has been repaired or
replaced.
Unplug the chargerand disconnect it from the skateboard when not in
use.
CAUTION
BATTERY CHARGING INFORMATION
MEEPO Aurora Skateboard: Rated Input: DC 50.4V 6A

Power cord is used as a disconnection device. To fully de-energize
equipment for service,disconnectthe chargerpower cord.
WARNING
The charger is designed for indoor use only. Do not expose the charger to
liquid, moisture or extreme humidity. Do not charge the Meepo skateboard
or Meepo remote outdoors or in the rain.
PRODUCT AND BATTERY DISPOSAL INFORMATION:
Stop charging the skateboard and/or remote if charging isn’t completed
within the specified time.
Stop charging the skateboard and/or remote if the batteries become abnor-
mally hot, show signs of odor, discoloration, deformation, or if abnormal
conditions are detected during use, charging, or storage.
Do not charge the skateboard and/or remote if the battery enclosure
becomes cracked, swollen, or shows any other signs of damage. Discontinue
use immediately and promptly dispose of unit.
Your device should not be placed in municipal waste. Please check
local regulations for proper disposal of electronic products.
If this unit shows any type of damage, such as bulging, swelling, or malforma-
tion, discontinue use and immediately contact Customer Service by sending
a mail to [email protected].
Dispose of used batteries in accordance with the prevailing community regu-
lations that apply to the disposal of batteries.
Never dispose of used batteries with other ordinary solid wastes.
Batteries contain toxic substances.
This board is covered by a 180 day manufacturer’s warranty that covers
defects in workmanship and material. This does not cover damage caused by
abuse, misuse, negligence, accidents, or riding in water.
If the product has a manufacturing defect within 180 days of ship date,
contact [email protected]
Each board was tested for at least 20 miles before shipping it out. So it is
normal to spot some dirt or dust on the board, and certain mileage on the
remote.
Please keep your shipping box. The warranty does not include damage from
return shipping with lack of package material.
For any concerns regarding your board, please contact Meepo’s customer
service by going to www.meepoboard.com or by sending an email to:
[email protected].
WARRANTY AND MAINTENANCE
LIMITED WARRANTY
Store your board in a dry area. If you are not going to ride your board for a
long time, fully charge your board at least once a month to unrecoverable
prevent irreversible battery damage.
MAINTENANCE FOR BOARD WHEN NOT BEING USED
FOR ALL RETURN AND WARRANTY SHIPPING:
If you accidentally ride in the rain or on wet surfaces, wipe off all the water on
the surface of your board, especially the charging port. Do not charge your
board until it is completely dry. Then, run the motors so that the wheels are
spinning for 10 minutes in order to dry the inside of the motors and avoid rust.
MAINTENANCE AFTER WET SURFACES

MEEPO ELECTRIC
SKATEBOARD COMPANY
Online Store Customer Service
Room 2015, Trend Centre, 29-31 Cheung LeeStreet, Chai Wan, Hong Kong
Company address
Online Store
www.meepoboard.com
Customer Service Email Address
[e-mail]