MegaLite XS Led Strobe W User manual

USER MANUAL
Table of Contents
Safety Information…………………………………………………..…3
Specifications…………………………………………………………..4
Main Power Connection…………………………………………….. 5
DMX-512 Connection……………………………………………...... 5
Main Control Menu.........................................................................6
DMX Profile.................................................................................... 8
Rigging the Fixture……………………………...…………………….11
Cleaning & Maintenance................................................................11
Parts List........................................................................................11

Check that the unit has not been damaged during transport
Protection Against Fire
1. Maintain a minimum of 1 foot distance from any type of flame.
3. Replace fuse only with the specified type and rating.
4. Do Not install the unit to close to a heat source.
5. Make sure cable are properly secured
6. Maximum surface operating temperature 80º.
Protection Against Fire
1. Disconnect power before servicing.
2. For connection to main power supply proceed to page 5.
3. This unit must be earthed. (electronically grounded)
4. Do not expose unit to rain or moisture.
Protection Against Mechanical Hazards
1. Use safety chain when hanging unit.
2. Use quality clamps or bolts when positioning unit
3. Do not open unit while it is on, risk of electrical shock.
3

Technical Information
4
3010– XS Led Strobe White
Mechanical Specifications
Fixture 6 Unit ATA Road Case
Size: 13.66” x 4” x 7.12
Weight: 6.5 lb
Size: 30.5” x 23” x 20.66”
Weight: 60.5 lb (empty)
Electrical Specifications
DMX 512 Protocol
DMX Modes: Mode 1 1 Channels Strobe
Mode 2 3 Channels Dimmer, Duration, Strobe
Mode 3 4 Channels Dimmer, Duration, Strobe, Macro
Mode 4 7 Channels Dimmer, Blinder, Duration, Strobe, Macro, 3 Segment Macros, 9 Segment Macro
Mode 5 13 Channels Dimmer, Intensity X9, Strobe, Macro
Mode 6 1Channel Dimmer
Mode 7 3 Channels Dimmer x 3
Mode 8 9 Channels Dimmer x 9
Control Options: Display Control, Master Slave
Control & Programming
DMX Connectors: 5 pin XLR connectors in and out
Thermal: Maximum ambient temperature 104°
Maximum surface temperature 140°
Fastening System: Single Mounting Yoke
Display: Digital
Power connection: Power Con in & out
LED Quantity: 324 White SMD LEDS 6500K LED Angle: 140°
Power Input Voltage: 110V-240 50/60 Hz Fuse: 5x20 F5AL250V
Ballast: Electronic auto switching
Power Consumption Watts: 259
Amps: 3.49
LED Watts: .80
LED Lifetime: 60 to 100 thousand hours
Part Numbers
4”
7.12”
13.66”
4.8”

5
Main Power Connec-
Caution!
1. Do not connect fixture to a dimmer system.
2. This unit has Auto switching power supply. It will respond to 110V or 220V automatically
3. This unit must be earthed. (electronically grounded)
4. Replace fuse only with the specified type and rating.
The occupation of the connection-cable is as follows:
DMX-512 Connec-
This fixture is equipped with an electronic power supply that will let the unit operate from 90V to 240V from 50Hz to
The fixture is equipped with 5 pin XLR Sockets for DMX input and output. The sockets are wired in parallel. Only use a
shielded twisted pair cable designed for RS-485 and 3 pin XLR plugs and connectors in order to connect the controller
with the fixture or the fixture with another.
Caution!
At the last fixture the DMX signal needs to be terminated with a terminator. Solder a
120 Ohm resistor between the (-) and the (+) signal into a 3 pin XLR plug and plug it
in to the last fixture on the signal run. Pre-manufactured terminator plugs are availa-
ble for purchase from your Mega-Lite dealer (P-DMXT).
Cable (USA) Cable (EU) Pin 110V
Black Brown
White
Green
Light Blue
Yellow/Green
Live
Neutral
Ground
L
N
L
L
220V
L
L
110V
Connec-
220V
Connec-
N
L
DMX—input DMX—output
1. Shield
2. Signal (-)
3. Signal (+)
5
3
4
2
11
2
3
4
5
4. N/A
5. N/A

Display Menu
6
The control board on the fixture base is your interface to access and
control all the functions on the unit. Its digital display gives you a code
view of the options and functions. The following will explain each func-
tion and its options.
ESC DOWN UP ENTER
CONTROL BOARD
Address
001
Work Mod
DMX 512
DMX 512= This mode will allow you to operate the fixture with a DMX con-
troller
Master= This Function Allows you to run the Auto Programs Or Audio Pro-
grams and send DMX signal out to the Slave units
Slave= On Slave Mode the fixture will copy the functions on the Master unit
To Set the Desired operational mode press Enter. Use the Down or Up to select
the desired mode and press Enter to confirm your setting.
—Mega Lite—
XS LED W
To Set the DMX Start Channel press Enter. Use the Down or Up to select the
desired DMX Start Channel and press Enter to confirm your setting.
Chan Mod
ACH
To set the desired operational channel mode press Enter. Use the Down or Up to
select the desired DMX profile operational mode from A,B,C,D,E,F,G and H press
Enter to confirm your setting.
Note: Operational mode are located on Page 8 of the manual.
Auto
This function will give you access to the Preprogramed Chases Press Enter.
Use the Down or Up to select the programed chase, press Enter to confirm your
setting. Use the Down or Up to select the desired speed of the Chase from 1 to 5
press Enter to confirm your setting

7
Tools
This function will give you access to the Display Control press Enter. Use the
Down or Up to select the desired display operational Mode from Display On
that will leave the display always turned on. Or Display Auto that will make the
display turn off after no usage for 20 seconds., press Enter to confirm your set-
ting.
Display
Mode
Time
This function will give you information of how long the fixture has been turned on.
Temp
This function gives you information of the fixtures current temperature
Key Mode
This function will give you access to lock the menu keys so they are not accident-
ly moved. Press Enter. Use the Down or Up to select the desired Key settings
from Lock Or Unlock press Enter to confirm your setting. You will have to hold
the Enter button for 3 seconds, to unlock the keys.
DMX
Status
Value
Hold
Value
Clear
If DMX signal is lost. The Fixture will hold the last DMX value
sent.
If DMX signal is lost. The fixture will bring dimmer channels to
zero.
Strobe
Set
This function will give you access to set strobe rate via display. Press Enter.
Use the Down or Up to select the desired color. Press Enter use the Down or Up
to select intensity from 0 to 255. You can repeat this process to get any color
combination.
(Note) once strobe is set you can power up and the last strobe setting will auto-
matically come on.
Strobe
000
White 7
000
Intensity
Set
This function will give you access to set Intensity via display. Press Enter. Use
the Down or Up to select the desired intensity. Press Enter use the Down or Up
to select intensity from 0 to 255. You can control each of the 9 sections .
(Note) once intensity is set you can power up and the last Intensity setting will
automatically come on.

8
DMX Profile
XS LED W 1 Ch A Mode
DMX Channel Function Description Value
No Function 0-5
1Strobe Strobe Rate (slow to fast) 6-249
Blinder (full on) 250-255
XS LED W 3 Ch B Mode
DMX Channel Function Description Value
1Dimmer No Function 0-255
2Duration Flash Duration 0-255
3Strobe No Function 0-5
Strobe Rate 6-255
XS LED W 4 Ch C Mode
DMX Channel Function Description Value
1Dimmer No Function 0-255
2Duration Flash Duration 0-255
3Strobe No Function 0-5
Strobe Rate 6-255
No Function 0-5
Ramp Up Effect (slow to fast) 6-42
Ramp Down Effect (slow to fast) 43-85
4Macro Ramp Up-Down Effect (slow to fast) 86-128
Random Effect (slow to fast) 129-171
Lightning Effect (slow to fast) 172-214
Spike Effect 215-255

XS LED W 7 Ch D Mode
DMX Channel Function Description Value
1Dimmer Dimmer 0-255
2Blinder Full Off 0-126
Full On 127-255
3Duration Flash Duration 0-255
4Strobe No Function 0-5
Strobe Rate 6-255
No Function 0-5
Ramp Up Effect (slow to fast) 6-42
Ramp Down Effect (slow to fast) 43-85
5Macro Ramp Up-Down Effect (slow to fast) 86-128
Random Effect (slow to fast) 129-171
Lightning Effect (slow to fast) 172-214
Spike Effect 215-255
No Function 0-1
Macro 1 (slow to fast) 2-25
Macro 2 (slow to fast) 26-50
Macro 3 (slow to fast) 51-75
3 Segment Macro 4 (slow to fast) 76-100
6Macro Macro 5 (slow to fast) 101-125
Macro 6 (slow to fast) 126-150
Macro 7 (slow to fast) 151-175
Macro 8 (slow to fast) 176-200
Macro 9 (slow to fast) 201-225
Macro 10 (slow to fast) 226-255
No Function 0-1
Macro 1 (slow to fast) 2-25
Macro 2 (slow to fast) 26-50
Macro 3 (slow to fast) 51-75
Macro 4 (slow to fast) 76-100
79 Segment Macro 5 (slow to fast) 101-125
Macro Macro 6 (slow to fast) 126-150
Macro 7 (slow to fast) 151-175
Macro 8 (slow to fast) 176-200
Macro 9 (slow to fast) 201-225
Macro 10 (slow to fast) 226-255
9

XS LED W 13 Ch E Mode
DMX Channel Function Description Value
1Dimmer Dimmer 0-255
2Intensity Segment 1 Intensity 0-255
3Intensity Segment 2 Intensity 0-255
4Intensity Segment 3 Intensity 0-255
5Intensity Segment 4 Intensity 0-255
6Intensity Segment 5 Intensity 0-255
7Intensity Segment 6 Intensity 0-255
8Intensity Segment 7 Intensity 0-255
9Intensity Segment 8 Intensity 0-255
10 Intensity Segment 9 Intensity 0-255
11 Duration Flash Duration 0-255
12 Strobe No Function 0-5
Strobe Rate 6-255
No Function 0-5
Ramp Up Effect (slow to fast) 6-42
Ramp Down Effect (slow to fast) 43-85
13 Macro Ramp Up-Down Effect (slow to fast) 86-128
Random Effect (slow to fast) 129-171
Lightning Effect (slow to fast) 172-214
Spike Effect 215-255
XS LED W 1 Ch F Mode
DMX Channel Function Description Value
1Dimmer Dimmer 0-255
XS LED W 3 Ch G Mode
DMX Channel Function Description Value
1Dimmer Dimmer Segment 1 0-255
2Dimmer Dimmer Segment 2 0-255
3Dimmer Dimmer Segment 3 0-255
XS LED W 9 Ch H Mode
DMX Channel Function Description Value
1Dimmer Dimmer Segment 1 0-255
2Dimmer Dimmer Segment 2 0-255
3Dimmer Dimmer Segment 3 0-255
4Dimmer Dimmer Segment 4 0-255
5Dimmer Dimmer Segment 5 0-255
6Dimmer Dimmer Segment 6 0-255
7Dimmer Dimmer Segment 7 0-255
8Dimmer Dimmer Segment 8 0-255
9Dimmer Dimmer Segment 9 0-255
10

11
Cleaning and maintenance
Installation Maintenance: The operator has to make sure that the unit is operating safely and has the installa-
tions and electronics checked by an expert every 2 years.
The following points have to be considered during the inspection:
1) All screws used for installing the device or part of the device have to be tightly connected and must not be corroded.
2) There must not be any deformations on the housing, fixation and installation spots (ceiling, suspension, trussing).
3) The electronic power supply cables must not show any damages, material fatigue (e.g. porous cables) or sediments.
Further instructions depending on the installation spot and usage have to be adhered by a skilled installer and any
safety problems have to be removed.
Note: There is no serviceable parts inside the device except for the LED’s. Maintenance and service operations are
to be carried out by authorized dealers.
Replacing the fuse: Only replace the fuse with the same type and rating.
Replacing the power cable: If the power cable of this device becomes damaged, it has to be replaced by author-
ized dealers or trained professional only.
Should you have further questions , please contact your dealer.
Parts List
3010-PCBM Main PCB card
3010-PS Power Supply
3010-WLED White LED Replacement
3010-WLEDM White LED Module
3010-FAN Replacement fan
Rigging the fixture
Caution!
1. The installations must be carried out by an authorized dealer or trained professional.
2. Unit may cause severe injures if you have doubts concerning the safety do not install.
3. Unit is to be 24inches away from flammable materials (decoration material)
4. Use high quality installation equipment to hang unit.
When rigging a unit it is very important that you follow common safety procedures. Rigging requires extensive experi-
ence including but not limited to calculating working loads, material being used and periodic safety inspections. If you
lack these qualifications, do not attempt the installation yourself, instead use a professional structural rigger.
When rigging the unit always be secured with a secondary safety attachment. The installation location of the fixture has
got to be built in the way that it can hold 10 times the weight for 1 hour with out any harming. Installation should be
checked at least one time a year by a skilled person.
3010-MUL Multiple Unit Hanger
3010-KNO Knob Set
3010-RC 6 Unit Road Case

Mega-Lite
5718 Kenwick St
San Antonio, TX 78238
Ph 210-684-2600 Fax [phone]
www.mega-lite.com / [e-mail]
Warranty Information
Warranty Conditions
-Unless otherwise stated in writing, your product is covered by a one year parts and labor limited warranty.
-LEDs are not guaranteed to match in color temperature or output.
-It is the owner’s responsibility to furnish receipts or invoices for verification of purchase, date, and reseller or distributor.
If purchase date cannot be provided, date of manufacture will be used to determine warranty period.
-Goods returned under warranty must follow the proper authorization procedure and must be accompanied by a copy of
the original invoice.
-Goods repaired under warranty will be returned to the owner with the freight prepaid by MSI via the most economical
means of shipment.
-Repair or replacement as provided for under this warranty is the exclusive remedy of the consumer. MEGA SYSTEMS
INC. makes no warranties, express or implied, with respect to any product, and Mega Systems specifically disclaims any
warranty of merchantability or fitness for a particular purpose. Mega Systems shall not be liable for any indirect, inci-
dental or consequential damage, including lost profit, sustained or incurred in connection with any product or caused by
product defect or the partial or total failure of any product regardless of the form of action, weather in contract, tort
(including negligence), strict liability or otherwise, and weather or not such damage was foreseen or unforeseen.
- Warranty is void if the product is misused, damaged, modified in any way, or for unauthorized repairs or parts. This
warranty gives you specific legal rights, and you may also have other rights which vary from state to state.