Hand&Eye Isla Original instructions

[e-mail]
handandeyestudio.co.uk
©October 2022
Lighting for all the senses.
Isla
Instructions & Safety
Information EU/UK
Design by
Thomas Housden
Material & nish
Through colour porcelain
Dimensions & weight
Ø83-84mm, H.142-144mm, 0.6-0.7kg
Projection from wall: 94mm
Lamp type & wattage
• Integrated low voltage LED, 2700k or 3000k, 14w
• Approx 900 lumens
• LED driver (350mA constant current) supplied
• Not suitable for surface mounted conduit electrical
distribution
• Dimmable with suitable dimmers/interfaces
IP rating
IP20
Wiring certication
CE / UKCA EN60598
Options
Colour: dark grey, light grey, pink, cream
94
mm
3.7 inch
83 mm
3.26 inch
143 mm
5.62 inch
113 mm
4.44 inch
143 mm
5.62 inch
113 mm
4.44 inch
85
mm fixing ctrs
3.34 inch
Dimensions- Side view Dimensions- Front view
94
mm
3.7 inch
83 mm
3.26 inch
143 mm
5.62 inch
113 mm
4.44 inch
143 mm
5.62 inch
1
13 m
m
4
.44 inc
h
85
mm fixing ctr
s
3
.34 inc
h
Dimensions- Top view
94
mm
3.7 inch
83 mm
3.26 inch
143 mm
5.62 inch
113 mm
4.44 inch
143 mm
5.62 inch
113 mm
4.44 inch
85
mm fixing ctrs
3.34 inch

[e-mail]
handandeyestudio.co.uk
©October 2022
Lighting for all the senses.
Isla
Safety Information EU/UK
• Please read the instructions before assembly or
installation.
• Make sure mains power is OFF during installation.
• Be sure to use a suitably qualied person for
installation as the lights require connecting to mains
power.
• Install the light to all relevant local building codes and
standards.
• Note the integrated LED modules are low voltage
LEDs with a remote driver/transformer required..
• Ensure the driver provided is used at the correct mA
setting as incorrect drivers or driver settings can
damage the LED and cause overheating.
• Make sure the wall is suitably prepared to ensure a
solid xing method and substrate.
• The ceramic shades are breakable and should be
treated suitably.
• Do NOT touch the LED surface if the lens cap is
removed.
• Do NOT touch the LED module when turned on if the
lens cap has been removed or broken.
• Do NOT disassemble the LED module from the
heatsink.
• Do NOT bring the lamp in contact with water or locate
the lamp in a wet location.
• If the cables are damaged, these must only be
replaced by the manufacturer or a similarly qualied
person.
• Used electrical equipment (WEEE) should not be
mixed with general household waste. Please recycle.
Our products can be dismantled prior to disposal.
• For LED module replacements contact Hand & Eye.

[e-mail]
handandeyestudio.co.uk
©October 2022
Lighting for all the senses.
Isla EU/UK
Assembly Instructions 1/2
1. Ceramic shade
2. Ceramic backplate
3. LED assembly
4. LED lenses and edge cap
5. LED xing block
6. Wago electrical connectors
7. Heavy duty plasterboard xings
8. Brass bolt
(low voltage driver - see diagram 3)
Diagram 1
Lamp components & assembly
1
Steps
The Isla wall light comes pre-assembled for safe transit
with parts 1,2,3,4 & 5 pre assembled.To install the lamp
follow the below steps carefully.
1Install the external driver
The lamp requires a driver to provide the low voltage
power supply to the integrated LEDs.
We recommend installing the driver in an accessible
location such as a cupboard or services room.
Connect the mains side of the driver to the mains power
and run suitable cables from the driver to the location of
the wall light.
For full information on the maximum distance possible
between driver and LED please contact the driver
manufacturer. As a guide, most of the drivers that we
supply can be located up to 20m (65 foot) away from the
wall light using a mimimum cable section of 0.5mm2 or
further (potentially up to 50m) if 1mm2 cable is used.
See diagram 3 for electrical wiring diagram
Note!
• A qualied electrician MUST be used to connect
the wall light to the mains power.
• Always ensure the mains power is turned OFF
when installing the lamp.
• These LED modules are low voltage LEDs that
require a remote driver of maximum 350mA
2Locate wall xings
The lamp is supplied with 2 heavy duty plasterboard
xings (7). Locate the desired lamp location and mark
the two xing holes located at the top and bottom of the
ceramic back plate.
Note!
• This dimension should be 85mm but as the lamp
is ceramic there can be minor variations. We
recommend oering up the ceramic back plate to
check.
Drill two 7mm holes and insert the heavy duty rawplugs.
Thread in the bolt and tighten into the rawplug without
the ceramic lightshade attached.This will secure the
rawplug to the back of the plasterboard.
Remove the bolt from the rawplug.
https://www.rawlplug.co.uk/product/sm-interset/
2
3
4
5
6
7
7
Diagram 2
Rawplug Interset Diagram
8

[e-mail]
handandeyestudio.co.uk
©October 2022
Lighting for all the senses.
Isla Wall EU/UK
Assembly Instructions 2/2
3Connect lamp to driver
Connect the low voltage cables from the driver to the
LED cables ensuring to the correct polarity as shown in
the wriring diagram 3.
Adjust cable length to suit.
Note!
• Ensure mains power is switched o
• Check the driver is set to 350mA if the driver has
multiple mA settings!
• Test lamp is working before securing to wall
4Check lamp is facing correct direction
The light has a correct up and down side. The LED (3) can
slide o the LED xing block (5) if located upside down.
Ensure the the xing block stop is located at the bottom
of the lamp. See diagram 4.
5Secure lamp to wall
Locate the ceramic shade against the wall and align the
top xing hole with the top tted rawplug heavy duty
plasterboard xing (7). Thread the brass bolt (8) through
the shade and into the threaded rawplug (7).Tighten
gently using ngers or a small screw driver to ngertight.
Do not overtighten as this may crack the ceramic.
Repeat process on bottom xing position.
Note!
• Do not overtighten xings screws
Diagram 4
Correct lamp direction
Diagram 3
Wiring diagram
- Negative (BLACK)
Wago 221
+ Positive (RED)
Wago 221
LED 1
LED 2
Driver
Low voltage
UPWARDS FACING LED =
BLACK HEATSINK VISIBLE IN
FIXING BLOCK