Memphis Shades 2321-0032 User manual

2321-0032 ROADLINER FATS/SLIMS MOUNTING KIT - 06
MOUNTING INSTRUCTIONS
Read and follow these directions carefully.
During installation, make certain that when turning the
forks, there can be no interference with wiring or cables
AND, that the windshield can not hit the gas tank,
through the windshield's full range of adjustment.
This is a detachable windshield, ALWAYS make sure the
Locking Mechanism is Fully Engaged after installing the
windshield!
The improper installation of this kit and related compo-
nents could result in serious injury or death.
IMPORTANT CARE AND CLEANING INSTRUCTIONS
Memphis Shades Windshields and Lowers are made of
Lucite® acrylic, and will last for years with proper care.
Clean your windshield with plenty of soapy water — mild
dishwashing liquid is best — and a soft cotton cloth. Use your
bare hand to feel and dislodge bugs, or cover with a wet soapy
towel and let it soak. Don't use paper towels and don't scrape
with anything. Small scratches can be removed with NOVUS
# 2.
NEVER use any glass cleaning products, petroleum based
chemicals, or cleaning agents with ammonia, bleach or any
other harsh chemicals. This includes (but not limited to)
RainX, brake fluid, acetone, paint thinner, benzene and
gasoline. "If it hurts your nose, it will hurt the plastic."
Glass cleansing agents will cause severe damage
to your windshield, and will void your warranty.
NOTE: At certain times of the day the Sunlight can reflect
off the curvature of a windshield and cause extreme heat
build-up on motorcycle instruments and instrument panel.
Take care when parking. Park facing the sun, place an opaque
object over the instruments or adjust the windshield to avoid
reflections.
First Bolt
Third
Bolt
Figure 2Figure 1
Additional tools required that are not included in this kit.
7/16" or 11mm Wrench.
1. Cover gas tank and front fender with towels to avoid
damage during installation.
2. Install the two mounting plates onto the windshield, using
the bottom and third bolt up. Leave the nylon washers off.
The small tab goes to the bottom, big one at the top. Tabs
point in towards the edge of the headlight (see fig. 1)
3. Using a 5mm Allen wrench. Locate and remove the two
upper Allen head bolts, one on each side of the headlight.
Save these bolts to install brackets. (see figure 2)
4. Install the right side bracket by placing the support washer
into the upper hole “the large part faces out, the small part
faces in” followed by the bracket and then loosely re-install
one of the upper bolts that was removed earlier. (see figure 2)
5. Locate and remove the two unused bolts in the lower triple
tree, one on each side of the headlight and discard. Install the
lower screw by inserting one of the new 8mm x 30mm button
head screws in this order, through the bracket, through the
spacer and tighten the lower and upper bolt.
6. Repeat step 5 for the left side bracket. (see figure 2)
7. Install the windshield by placing the lower slots into the
lower mounting bushings. Slip the upper slots into the upper
mounting bushings and gently but firmly seat the slots into
place.
Lock the locking mechanism into place. (see figure 3 and 4)
8. Adjust the height, angle and alignment of the windshield
and tighten ALL bolts.
Note: This is a detachable windshield, ALWAYS make
sure the Locking Mechanism is Fully Engaged after in-
stalling the windshield! (see figure 4)
Figure 3
Mounting bushings
MEM-8960 11-30-07

2321-0032 ROADLINER FATS/SLIMS MOUNTING KIT - 06
MOUNTING INSTRUCTIONS
2321-0032 FATS/SLIMS KIT
1. M1088
2. M1087
3. M1092
4. M1091
5. Stock Bolt
6. R320
7. M366
8. R319
1
3
2
4
5
7 8
6
1. Place lower slot
into lower bushing.
2. Rotate top slot into
place.
3. Secure locking
Mechanism.
1
2
3
Figure 4
MEM-8960 11-30-07
CORRECT
Fully engaged
NOT CORRECT
PART #
M8960 R319
DESCRIPTION
MOUNTING INSTRUCTIONS
1/2” SPACER
M366
R318
8mm x 30mm BUTTON HEAD CAP SCREW
1’’ SOCKET SHOULDER WASHER
4
2
2R320
1-1/2” SUPPORT SPACER
M1092 RIGHT MOUNTING PLATE FATS/SLIMS 1
M1091 LEFT MOUNTING PLATE FATS/SLIMS
QTY.
1
1
M1087 LEFT ROADLINER BRACKET
1
M1088 RIGHT ROADLINER BRACKET
1
PART # DESCRIPTION QTY.
2
M310
M313
3/16" SHORT ARM ALLEN WRENCH
3/16" ALLEN WRENCH COVER
1
1
R322C CLUTCH SIDE LATCH ASSEMBLY 1
R322T THROTTLE SIDE LATCH ASSEMBLY 1
R323 BUSHING ASSEMBLY (2 PART) 4
R324 #207 EPDM O-RING 4 R306 5mm LONG ARM ALLEN WRENCH 1
R321 1” RECESSED SPACER WASHER 4
R334 6-32 X 3/8" FLAT HEAD SS SCREW 8
R326 SS SPRING 2
M303 1/4"-20 X 3/4" SOCKET HEAD CAP SCREW 4
M505 BUTTON NUT 4
LATCH
ASSEMBLY
BUSHING
ASSEMBLY
Memphis Shades warrants all product components, metal and plastic,
against defects in materials and workmanship for 24 months.
FOR PARTS AND WARRANTY HELP, CONTACT:
MEMPHIS SHADES
P. O. Box 429
Rossville, TN 38066
[phone]
Visit us on the web at www.memphisshades.com or
you can also reach us by email:
[email protected]