Merrithew Stability Barre User manual

Please review this important assembly, safety and warranty information about your new
Merrithew™equipment and keep it handy for future reference.
OWNER’S MANUAL
Stability Barre™

Stability Barre Owner’s Manual2
User Guidelines
Pilates equipment when used effectively can faciliate many Pilates
exercises safely and effectively. However, care and caution must
be taken as there are some inherent dangers when using any
exercise equipment.
For inexperienced or first-time users, this equipment
should only be used under the supervision of a
trainedprofessional.
Please ensure that you and your clients/patients have
receivedproper instruction regarding the correct and safe
useofthis equipment.
This manual includes general guidelines for setup and usage.
To get the most out of this equipment, Merrithew offers
instructional DVDs and manuals. Personalized training is offered
through our Corporate, Licensed and Host Training Centers.
Visit merrithew.com for more information.
Mechanical
SafetyCheck
We recommend an inspection schedule as follows
Monthly: Check wear on all pop-up pins and knobs
andreplaceas necessary.
FAILURE TO PERFORM RECOMMENDED SAFETY CHECKS,
OR USINGEQUIPMENT WITH IMPROPERLY ADJUSTED,
BROKEN OR WORN PARTS, COULD RESULT IN SERIOUS
BODILY INJURY.
CAUTION IMPROPER USE OF EXERCISE EQUIPMENT MAY CAUSE SERIOUS BODILY INJURY. TO REDUCE RISK, PLEASE READ THE FOLLOWING:
wThe Stability Barre is designed to provide balance and
support during ballet and standing exercises. It is not
intended to carry full body weight. Do not lean against,
hang from, sit or stand on this equipment.
wBefore starting any exercise program, consult a physician.
wUse equipment for intended exercises only.
wEnsure the equipment is properly adjusted for your size
and ability level.
wStop exercising immediately if you experience chest pain,
feel faint, have difficulty breathing or experience discomfort.
wDo not use if equipment appears worn, broken or damaged.
wDo not allow children to use or be around equipment
without adult supervision.
wDo not hang from the barre or use it to pull yourself up.
wThe Stability Barre should not be used by persons weighing
over 350 lbs / 159 kgs.
wFlex-Band®exercisers or other resistance equipment should
only be used in conjunction with the Parallel Stability Barres.
WARNING: As with any athletic activity, the use of
exercise equipment involves risk of injury, damage
and/or death.
By choosing to use Merrithew equipment, you and/or
your clients/patients assume responsibility for that risk,
not the people who sell, distribute and/or manufacture
this equipment.
IMPORTANT!
This manual contains important assembly, safety and
warranty information. Read the manual carefully before
using your new equipment and keep the manual on
hand for future reference.
UNSAFE OR IMPROPER USE OF THIS EQUIPMENT
BY FAILING TO READ AND COMPLYWITH ALL
REQUIREMENTS ANDWARNINGS COULD RESULT
INSERIOUSINJURY.
It is impossible to predict every situation and condition
that can occur while using this equipment. Merrithew
makes no representation about the safe use of any
exercise equipment that cannot be predicted or
avoided.
PLEASE DO NOT ATTEMPT TO ASSEMBLE ON YOUR
OWN. SOME OF THESE STEPS REQUIRE TWO PEOPLE.
PLEASEREAD THESE INSTRUCTIONS COMPLETELY
BEFOREBEGINNING ASSEMBLY.
Merrithew recommends cautious assembly and
usage andwishesyou many hours of safe and
effectiveexercise.
Care and Cleaning
Wipe surfaces using warm water with mild soap and clear
water rinses for day-to-day cleaning. Ensure soap does not
leave an oily residue, or make surfaces slippery.
CAUTION: We do not recommend using chemical-
basedproducts.
STABILITY BARRE™OWNER’S MANUAL

3
Stability Barre Connectors
FOR PARALLEL BARRES ONLY
12' Parallel Stability Barre
includes 6 connectors
6' or 8' Parallel Stability Barres
include 4 connectors
PART IDENTIFICATION
Stability Barre
1Wooden Barre
2Guide Tubes
33-Prong Knob
4Pre-Drilled Holes
5Plastic Sleeve
6Pop-Up Pin
7Telescopic Support (Upright)
8Weighted Base Plate
9Rubber Feet
10 Metal Plate
Stability Barre™Options
wAvailable as Single or Parallel Barres
wWhite or Gray finish
w6', 8' and 12' lengths
wFor 8' Wall-Mounted Stability Barre
See page 8
11 Clamp
12 Connector
13 Fold-Over Locking Lever
1
2
3
4
5
6
9
8
7
1211 13
10

Stability Barre Owner’s Manual4
2. Insert guide tube [2] into telescopic support (upright) [7].
Lineup pre-drilled holes [4 ]withpop-up pins [6].
Tighten off the pop-up pin [6] by securely screwing closed.
Repeat for the other upright.
3. Insert the wooden barre [1] into the guide tubes [2] allowing
aminimum 3"/ 7.5 cm to protrude. Ensure the metalplate [10]of
the wooden barre is facing down.
NOTE: The tips of the 3-prong knobs [3] must be in contact
withthe metal plate [10]at all times when in use.
4. Tighten the 3-prong knobs [3] clockwise to secure the wooden
barre at both ends, ensuring themetal plate is in contact with the
3-prong knobs.
1. Attach the telescopic support (upright) [7] to the
weightedbase plate [8] by turning clockwise until tightened.
NOTE: Ensure the weightedbase plate is aligned
perpendicular to the vertical hole in the telescopic
support (upright) to ensure proper threading when
attaching the weightedbase plate.
min 3"
Assembling the 6' and 8' Stability Barres
STOP! Read these instructions completely before beginning or refer to our online assembly video at: merrithew.com/eq-assembly
ASSEMBLY INSTRUCTIONS
3
6
7
2
4
7
8
3
3
1
2

5
1. Repeat steps 1 and 2 from the Stability Barre Assembly (page 4) for all three uprights.
2. Insert one 6' wooden barre [1] into the first guide tube [2] allowing a minimum
3"/ 7.5cm overhang. Ensure the metal plate [10]of the wooden barre is always
facingdown.
3. Insert the other end of the wooden barre [1] half-way (5"/ 12.7 cm) into the center
ofthenext guide tube [2].
4. Insert the next 6' wooden barre into the guide tube [2] from previous step.
5. Finally, place the other end of the wooden barre throughtheremaining guide tube [2]
allowing a minimum 3"/ 7.5cm overhang and tighten all 3-prong knobs.
Insert each wooden barre
halfway thru the middle
guide tube of the center
telescopic support.
Assembling the 12' Stability Barre
STOP! Read these instructions completely before beginning or refer to our online assembly video at: merrithew.com/eq-assembly

1. Assemble two Stability Barres as described in the
Stability Barre Assembly [Page 4].
2. Use connectors [12]to join two Stability Barres.
To open Clamp [11]: release the fold-over locking lever [13]
and fold it away from the Clamp [fig.A].
3. Place the Clamp [11]around the telescopic support (upright) [7]
positioning it againsttheweightedbase plate [8]. Close and
lock the Clamp using the fold-over lockinglever [fig.B].
NOTE: fold-over locking lever may be rotated clockwise or
counter-clockwise toadjustthelength ofthe lever’s threaded
bolt[fig.A].
4. Attach the other end of the connector to the second
StabilityBarre atthesame height.
5. Attach the second Clamp to the telescopic support (upright) [7]
just below the pop-up pin [6].
6. Repeat steps 2-6 above until all connectors are attached and
theunit isfully assembled.
NOTE: Parallel Stability Barres are sold as a kit with all the
connectors included.
If you have purchased single 6', 8' or 12' Stability Barres and wish
to join them together, connectorsare also sold separately in pairs.
12' require
6 connectors
6' or 8' require
4 connectors
Shown with the
fold-over locking
lever in place
andclamped shut
B
wTurn clockwise
to tighten
wCounter-clockwise
to loosen
A
Assembling the Parallel Stability Barres
STOP! Read these instructions completely before beginning.
ASSEMBLY & SET-UP
6
7
8
11, 13
11, 13
Adjustable
Threaded Bolt

Adjusting the Wooden Barre Height
The telescopic support (upright) comes with Pre-drilled Holes [4]
for height adjustment to accommodate the users' needs, and can
be adjusted from 36-1/2"/ 92.7 cm to 44"/ 111.8 cm.
1. Loosen (unscrew) and pull out the pop-up pin [6].
2. Adjust wooden barre to the desired height.
3. Release and insert pop-up pin to ensure it has engaged fully
into oneofthe Pre-drilled Holes.
4. Tighten the pop-up pin.
NOTE: Place your foot onto the Weighted base to hold it down
priorto adjusting the height.
IT IS RECOMMENDED THAT ANY ADJUSTMENTS IN HEIGHT
BE MADE SIMULTANEOUSLY USING TWO PEOPLE,
ONE AT EACH END.
Leveling the Base Adjustment
The weightedbase plate [8] comes with adjustable Rubber Feet [9]
to accommodate most flooring.
Loosen (unscrew) or tighten (screw) Rubber Feet [8] as required
toassist in the leveling of your Stability Barre.
Setting Up the Stability Barre
8
9
4
6

Stability Barre Owner’s Manual8
Required Tools (not supplied)
Builder’s Level
Electric Drill
1/8" Allen Key
Hardware Required
not included QTY
Affixing to Drywall
Butterfly toggle or
slotted hex head wall anchors 6
Affixing to Brick Wall
Masonry fasteners 6
Assembling the Wall-Mounted Stability Barre
PLEASE DO NOT ATTEMPT TO ASSEMBLE ON YOUR OWN.
We highly recommend that you have this product installed by a professional contractor. Read instructions completely
beforebeginning assembly. Improper installation voids equipment warranty. Merrithew will not be responsible for any
injuryor damage resulting from improper installation.
wPlace all parts from the box in a cleared area and position
themon the floor in front of you.
wRemove all packing material from your area and place
themback into the box.
wDo not dispose of the packing materials until assembly
iscompleted.
wTo prevent unsafe or improper use, please read each
stepcarefully before beginning.
1. Find support studs in wall (typically 16"/ 40.64 cm apart)
andmark location.
2. Position one of the brackets at your desired height,
ensuring it is level.
3. Using a builder’s level ensure the bracket is perpendicular
to the floor. Mark attachment point holes against the wall
withapencil.
4. Remove the bracket and drill appropriately sized holes
throughthe wall.
5. Repeat steps 2 to 4 for the other bracket, ensuring that the
second bracket is at the same height as the first, and there is
aminimum of 3" of the barre protruding past either end of
thebrackets’ guide tube on each bracket.
6. Position each bracket and screw them firmly into the wall.
There are three [3] attachment point screw holes per bracket.
7. Insert the barre through one bracket, then into the next.
Ensuring there is a minimum of 3" protruding past either end
of the guide tubes.
8. Using a 1/8" Allen key, lock the set screws (2 per bracket) to
secure the barre
NOTE: On a standard drywall surface, when only one support
stud can be found, affix the remaining bracket to the wall using
butterfly toggle anchors, slotted hex head wall anchors or other
appropriate heavyduty drywall anchor fasteners. Brick walls
require six masonry fasteners.
CAUTION: Before use, test that the brackets are securely
attached to the wall.
HEIGHT TIP: Standard single wall mount barre height ranges
from 32"-46" from floor which is approximate waist-level.
Part Identification
1Bracket (2)
28' Metal Barre
1 2
ASSEMBLY & SET-UP

9
Soft Dumbbells and
Mini Handweights
For toning arms or increasing
intensity. Straps ensure a snug
fitin the palm of the hand.
Sold in pairs.
Mini
Stability Ball™
Create instability to fire up your
muscles. Four sizes, 5", 7.5",
10"and 12". Sold individually.
Flex-Band®
Exerciser
Additional resistance forthe arms,
challenges control of elbow,
shoulder and wrist movements.
Two strengths. Also available in
three latex-free strengths.
Strength
AnkleTubing
Provides additional resistance
forthe legs, challenging
strength, balance and stability
ofthe ankle, knee and hip joint.
Three strengths. Soldindividually.
Pop-up Pin
Use to adjust telescopic
supports(Uprights).
3-Prong Knob
Secures or unlocks the
WoodenBarre.
Stability Barre Connectors
Configure individual Stability Barres into Parallel Stability Barres.
Soldin sets of two. Included in the Parallel Barre Kits.
Available ingray or white.
Optional Items
Replacement Parts
For more information and to place an order, visit merrithew.com/replacementparts or email [e-mail]
MAINTENANCE & REPLACEMENT PARTS
ACCESSORIES

Stability Barre Owner’s Manual10
THE FINE PRINT
Warranty
Merrithew™warrants that all new equipment is free of manufacturing defects in workmanship and materials, subject to the terms below.
Thiswarranty becomes effective at the invoice date of the original purchase. Parts repaired or replaced under the terms of this warranty willbe
warranted for the remainder of the original warranty period.
It is the purchaser’s responsibility to notify the Company of any change of contact information. This ensures, that in the unlikely event
ofareplacement or safety notice, we are able to contact you immediately.
This warranty applies to equipment only:
w While it remains in the possession of the original purchaser
and proof of purchase is demonstrated
wIf claims are made within the part-specific warranty period
w If upgrades are made as required by Merrithew
This warranty shall be null and void if:
w Equipment failure is a result of improper assembly,
installationormaintenance
w The equipment is used for any other purpose other than
asintended, or is stored or used outdoors, or in environments
without adequate climate/humidity controls
wEquipment has been subjected to accident, misuse, abuse,improper
service, or any modification not authorizedbyMerrithew
This warranty does not cover damage to the finish of any equipment
nor shipping charges, customs clearance fees (if applicable), or any costs
incurred in installing repaired or replacement parts shipped under the
provisions of this warranty.
Limited Lifetime Warranty
Merrithew will, at its option, repair or replace any of the parts listed below,
provided that the part(s) fail due to a defectin workmanship
ormaterials and provided such failure occurs andisreportedwith
part-specific warranty period.
wTelescopic Supports (Uprights)
wGuide Tubes
wWeighted Base Plates
wWall Mount Bracket
Two (2) Year Limited Warranty
Merrithew will, at its option, repair or replace all other components that
fail for any reason, provided such failure is reported to Merrithew within
aperiod of two years from the invoice date of the original purchase.
Disclaimer of Implied Warranties and LimitationofRemedies
Repair or replacement of defective parts is your exclusive remedy under
the terms of this limited warranty. In the event of parts availability issues,
Merrithew will not be responsible for any consequential or incidental
damages arising from the breach of either this limited warranty or any
applicable implied warranty, or for failure or damage resulting from acts
ofnature, improper care and maintenance, accident, alteration, replacement
of parts by anyone other than Merrithew, misuse, transportation, abuse,
hostile environments (inclement weather, acts of nature), improper
installation or installation not in accordance with local codes or
printedinstructions.
This limited warranty is the sole express warranty given by
Merrithew. No product performance, specification or description
wherever appearing is warranted by Merrithewexcept to the extent
set forth in this limited warranty. Any implied warranty protection
arising under the laws of any state, provinceor territory including
implied warranty of merchantability or fitness for a particular
purpose, oruse, is hereby limited in duration to the duration of this
limited warranty.
Neither distributors, dealers, web resellers, nor the retailers selling this
product have any authority to make any additional warranties or to
promise remedies in addition to, or inconsistent with those stated above.
Merrithew’s maximum liability, in any event, shall not exceed the purchase
price of the product paid by the originalpurchaser.
IMPORTANT
Please keep this manual in a safe place.
If you have questions, issues or are missing parts:
Do NOT return this unit to your local retailer,
please contact the manufacturer directly.
[e-mail]
416.482.4050 |1.800.910.0001 |0800.328.5676 UK |ext. 0907

Make the Most of Merrithew™Equipment
As Leaders in Mindful Movement™, Merrithew is committed to developing unique, top-quality fitness programs
based on the latest in exercise science and research. Our signature STOTT PILATES®education is unparalleled,
and we bring the same expertise and passion to our full range of branded programs, including CORE™Athletic
Conditioning and Performance Training™, ZEN·GA®, Total Barre™and Halo®Training. Join our global community
of elite fitness professionals. Merrithew courses and workshops are offered worldwide.
Find courses and workshops near you at merrithew.com/education/training
Contact Us 416.482.4050 | 1.800.910.0001 | 0800.328.5676 UK | ext. 300
Expand Your Barre Repertoire
Get the most out of your equipment with ongoing training!
Our high-energy, dynamic Total Barre™program integrates elements of Pilates, dance, cardio and strength training.
Thisprogram emphasizes correct biomechanics of movement combined with the power of music to increase strength,
flexibility, stamina and dynamic stability. Following a progressive template, suggested beats per minute are provided
andclose attention is paid to the importance of selecting and modifying exercises for specific clientele to create
safe and funclasses.
Total Barre is a program geared for everyone—no dance experience required!
Provide your clients with the safest and most impactful barre program available and watch them have fun doing it!
Explore merrithew.com/total-barre/instructor-training for courses andworkshops near you.
Total Barre™: The Foundation Manual —
A Comprehensive Guide to Buildinga Great Barre Program
is the most all-encompassing guide available. Offering fully illustrated,
step-by-step instructions and modifications to create fully rounded
TotalBarre classes, themanual is perfect for experienced fitness
professionals and those taking the Total Barre Foundation course.
Instructional DVDs: We offer almost limitless exercise
challenges in our clear and detailed repertoire of cutting
edge titles. For a full listing visit merrithew.com/shop/dvds

P00214 PM-ST02114A-6 OCT17 ™/® Trademark or registered trademark of Merrithew Corporation, used under license. Printed in Canada. All rights reserved.
Please keep this manual in a safe place.
IMPORTANT
2200 Yonge Street, Suite 500, Toronto, Ontario, Canada M4S 2C6
416.482.4050 | 1.800.910.0001 | 0800.328.5676 UK | ext. 0907
[email protected]om | merrithew.com