Metalicon PMA326 User manual

Installation Instructions
1
UNPACKING INSTRUCTIONS
ŸCarefully open the carton, remove contents and lay out on cardboard or other
protective surface to avoid damage.
ŸCheck package contents against the Parts List on the next page to assure that all
components were received undamaged. Do not use damaged or defective parts.
ŸCarefully read all instructions before attempting installation.
IMPORTANT SAFETY INFORMATION
ŸInstall and operate this device with care. Please read these instructions before
installation, and carefully follow all instructions contained herein. Use proper
safety equipment during installation.
ŸPlease call a qualified installation contractor for help if you don't understand these
directions or have any doubts about the safety of the installation.
ŸDo not use this product for any purpose or in any configuration not explicitly
specified in these instructions. We hereby disclaim all liability for injury or damage
arising from incorrect assembly, incorrect mounting, or incorrect use of this product.
www.metalicon.com
PMA326
POLE ARM FOR 6 MONITORS

Parts List
2
(1)Pole-a (2)Monitor Arm-b (6)VESA Plate-c
(1)Grommet Plate-e (1)M10 Bolt-f (1)M10 Washer-g (1)Spring Washer-h
(2)Spare Plastic
Cover-t
(1)Allen Key-r (1)Wrench-s(24)M4 Space-q
(24)M4x30 Bolt-p(8)M8x10 Bolt-n(1)Decorative Cover-m
(6)Nut-d
(24)M4x12
Thumb Bolt-o
CAUTION!
WARNING
(2)M10x15 Bolt-k(1) C-clamp-i (1) C-clamp Brace-j (3)C-clamp
Brace Bolt-l
!The monitor mount must be securely attached to a suitable desk top
(minimum 25mm thickness recommended) before fitting the arms
and monitors, failure to do this could lead to an unstable installation
which could result in damage or injury.

Remove the existing grommet to ensure a flat surface before
installing the desk mount.
1. Position the Pole (a) on the mounting surface and secure
using the Grommet Plate (e), M10 Washer (g), Spring Washer
(h) and M10 Bolt (f). Fasten the M10 Bolt using provided
wrench (s).
2. Install the Decorative Cover (m).
a
m
h
f
g
e
Step 1A C-clamp Installation
3
Step 1B Existing Grommet Hole Installation
1. Install the C-clamp Brace (j) to the pole (a) using 3pcs C-clamp Brace
Bolts (l), see Figure 1.
2. Install the C-clamp (i) to the pole assembly according to the thickness
of the desktop. The thickness can be changed in three positions.
Connect it using 2pcs M10x15 Bolts (k), and tighten using the Allen
Key (r). Tighten the C-clamp to the desktop using the 2pcs eye bolts,
see Figure 2.
3. Install the Decorative Cover (m).
a
j
l
Figure 1 r
k
Figure 2
i
m
eye bolt

Step 1C Drilled Grommet Hole Installation
1. Position the Pole (a) on the mounting surface and mark the
center hole. Remove the pole. Drill a 10mm diameter hole at the
marked position through the mounting surface.
2. Position the Pole (a) on the mounting surface and secure using
the Grommet Plate (e), M10 Washer (g), Spring Washer (h) and M10
Bolt (f). Fasten the M10 Bolt using provided Wrench(s).
3. Install the Decorative Cover (m).
a
m
h
f
g
e
b
n
Install arms (b) to the pole(a), please ensure the wire clips on
the arm (b) are on the under side of the arm.
Fasten the M8x10 Bolt (n) with the Allen Key supplied (r).
Step 2 Install Arms to the Pole
4
wire clip

Step 3 Attach the VESA Plate to the Monitor
For Monitor with Curved or
Recessed Back Use the plastic spacers
(q) and the longer screws (p) to secure
the VESA plate to the monitor.
q
p
For Monitor with Flat Back
Use the hand turn screws (o) to secure
the VESA plate directly to the monitor.
o
5
Step 4 Slide the Monitor onto the Head of Arms
Install the security nut (d). Make
sure the security nut is installed
before you rotate the monitor.
Slide the monitors onto the heads
of the Monitor Arm (b) as shown in
the above diagram.
d

6
Step 6 Adjust the Level of Monitors if necessary.
To adjust the height of Centre Monitor:
Turn the bolt counterclockwise to lower the
centre monitor, turn the bolt clockwise to
raise the centre monitor.
To ad just th e height of S ide M oni tors:
Remove the Nut (d) and turn the bolt counter-
clockwise with supplied Allen key (r) to raise
the monitor. Install the Nut (d) after the
adjustment.
r
r
Step 5 Adjust the Tilt Angle and Arms Torque
p
Remove the plastic cover, adjust
the torque of Arms (b) with
the supplied wrench (s).
Remove the plastic cover, tighten
the nut with the wrench (s) to
adjust the tilt angle tension.
s
Adjust the tilt angle tension