Miku Miku Life Monitor || M0101 Installation instructions

Quick Setup Guide
Miku Pro Smart Baby Monitor
Let's get started
Commençons
Empecemos
Miku Life Monitor || M0101

For installation videos, visit
Pour les vidéos d'installation, visitez
Para videos de instalación, visita
mikucare.com/support
Content | Contenu | Contenido
Safety | English
Installation for drywall | English
Limited warranty & compliance | English
Sécurité | Français
Seguridad | Español
Installation pour cloisons sèches | Français
Instalación para drywall | Español
Garantie limitée et conformité | Français
Garantía limitada y conformidad | Español
4
5
27
30
30
31
31
53
56

4
Safety
STRANGULATION HAZARD — Children have STRANGLED in cords.
NEVER attempt to use cord without the protective covering. Check protective covering before each use
to ensure that the cord is not exposed to your child. Immediately discontinue use if protective covering
is damaged or broken. This device is designed for indoor use only. This device is designed to be used
behind a standard crib and against the wall only. Use only the AC power supply included with your
Miku. Adult assembly is required. Keep small parts away from children when assembling. This product
cannot replace adult supervision. Ensure your child’s health by checking on him/her regularly. This
product is not a toy. Do not allow children to play with it.
DISCLAIMER — Miku Baby Monitor was created to help parents track factors that affect their baby’s
sleep schedule and general wellbeing. It is not intended to cure, treat, or prevent any disease or health
condition, including, but not limited to, Sudden Infant Death Syndrome (SIDS). No baby monitor can
ever replace you as a caregiver, or substitute for asking your doctor for medical advice.
WARNING:

5
5
Installation for drywall
ENGLISH

6
Universal Anchors Extra Screws &
Large Drywall Anchors
In the box
Optional universal hardware
Baby Monitor Screwdriver
Measuring Tape
Power Cord
UP
THIS SIDE
Pencil
Cable Guides
Power Supply
Wall Mount & Level
Wall Guides
Large Drywall
Anchors
Screws

7
What you’ll need
Note: If you would like to avoid wall installation
consider a Miku Stand.
For wall installation videos visit
mikucare.com/support
WiFi Internet
Smart Device

8
Get the app
Download the free Miku app from mikucare.com/app and create
your user account. Open the App and follow along to pair your Miku.
https://mikucare.com/app

9
1|
Position the crib against the preferred wall in the nursery.
IMPORTANT: CRIB CENTER MUST BE IN A STUD-FREE AREA OF
THE WALL. If unsure, use a stud finder. For wall surfaces other
than drywall, please go to mikucare.com/support
Installation for drywall
Stud-free

10
2|
Using the Measuring Tape, find the center of the crib and mark
the wall with a pencil.
Note: Center of crib must be within 6 feet of an electrical outlet.
Then, move the crib away from the wall.
Crib Center

11
3|
Step on the bottom of the Measuring Tape so it aligns with the
floor and your “Crib Center” mark on the wall. Lift the tape up
60 inches and mark at the “Mark Here” indicator.
Mark Here
60in
Crib Center
Floor

12
4|
Take the Wall Mount and place it over your mark at 60 inches so
you can see the mark through the center hole.
UP
THIS SIDE

13
5|
Use the Level below the Wall Mount to verify that it is level.
Mark the wall through the two holes in the Wall Mount.
UP
THIS SIDE

14
6|
Pull and remove the Level from the bottom of the Wall Mount.

15
7|
Using the Screwdriver, push and twist into the two marks to
create larger holes in the drywall. Only push as far as the black
tip of the Screwdriver.

16
8|
Push the Large Drywall Anchors into each hole and screw them
until they are flush.
Note: If the wall anchor doesn't screw into the wall easily, you
may have hit a stud. In this case no wall anchor is required for
that hole.

17
9|
Position the Wall Mount over the “+” holes of the anchors. Screw
the Large Screws into the “+” holes and secure the Wall Mount
until flush with the wall.
UP
THIS SIDE
Note: Screw flush to the wall.
Do not overtighten.

18
10 |
Unroll the Power Supply and align the top rubber indicator to the
center of the Wall Mount, leaving the top of the cord hanging.
Using the Screwdriver, push the rubber indicator into the Wall
Mount to secure the Power Supply.
UP
THIS SIDE

19
11 |
Slide the base of the Miku device into the Wall Mount until it
clicks.
UP
THIS SIDE

20
12 |
Plug the Power Supply into the back of the Miku device.