Milion D2105 User manual

D2105

1. This machine should be installed in a vehicable with 12V . Do not install it to trucks or
buses with 24V battery.
2.Do not install this machine in places impeding driver ’s vision or impacting driving.
3.In order to avoid traffic accidents caused by distracting drivers’ attention, drivers are
not allowed to operate this machine or view the screen during driving, please park the
vehicle in safe places.
4. Do not place this machine, vehicle augments or speakers under humid or wet
environment, otherwise, it will cause electric short circuit and then lead to distaser
or other damages.
5.Do not change fuse device on power connector attached to this machine, for
unmatched fuse will lose over-current protection on this machine, which may burn
this machine or even arouse fire disaster.
6.If there’s no sound, no image, or there is water or small impurities leaking into the
machine, or there comes smoke and smell, please stop using this machine, and send it
to the after-sale service center; otherwise, it may cause fire disaster or other accidents.
7. Please adjust the volume to a proper extent during driving, for overloud volume may
interfere drivers’ listening to information outside the vehicle.
Tips
1.When there’s any abnormal phenomenon in this machine during operation, please refer to solutions in “
Troubleshooting Guide” in this instruction, if no solutions could be found, please press the [Reset] button on
the panel with a sharp tip, to reset the machine to factory status.
2. When machine panel and TFT LCD are dirty, please wipe with soft cloth or neutral detergent; while hard cloth
or diluents like alcohol etc. may scratch the panel or make texts disappear.
3. Please do not touch the display with hard materials to avoid damaging the screen
4. This machine is composed of par ts of high precision, please do not dismantle the cover or tune any part by
yourself, please come to nearby professional after-sale ser vice center for repair.
5. Strong impact on the machine shall be avoided, for this will damage mechanical par ts of the machine.
6. When temperature inside the vehicle is too high or too low, please adjust temperature first, and then use this
machine.
7. After using the heater for cold weather, there will be dew (water) inside the player, in this case, do not play the
disc, take it out, and use it after removing the dew from the player. If it could not be played normally after
several hours, please contact the dealer.
8. Discs with irregular shapes could not be inser ted into this machine, otherwise, it will cause machine core failure.
9. Illustrations shownin this instruction are to illustrate how to control in a clearer way, so display interface in these
illustrations may be slightly different from actual interface of this machine, and illustrations of some display
screens may not be realized during actual operation.
10.During operation, when occurs on screen, it indicates that this operation is not supported by this
machine or the current operation is invalid.
11. Please operate this machine according to user manual, and any damage caused by illegal operation is not in
warranty scope.
Safety Notes
23
Prouduct Parameters

Table of Content
1
2
3
5
6
7-13
7
8
10
11
12-13
14
14-16
16
17-19
20
20-28
21
22
23
24
24-25
25
26
26
27
27
28
28-30
30-31
31
32
Vehicle Audiio & Video Usage Guide
Safety Notes
Tips
Table of Content
III Panel Button Instructions
IV Main Interface Functional Operations
V DVD Functional Operations
1. Secret button function
2. DVD Play
3. Search Play
4. JPEG Play
5. DVD/MP3/WMA Discs
VI USB/SD/iPod Function Operations
VII Radio Function Operations
IX External Input Function Operations
X Bluetooth Function Operations
XII Calendar/Clock Setting
XIII Setting Function Operations
1. General Settings
2. Touch Screen Calibration
3. Steering Wheel Control Setting
4. Factory Settings
5. Radio Settings
6. Bluetooth Settings
7. Video Settings
8. Volume Design
9. Media Settings
10. iPod Settings
XIV Remote Controller Operation
XV Notices
XVI Troubleshooting
XVII Product Parameters
III Panel Button Instructions
User could search corresponding functional operations according to panel button
prints in the table below:
Buttons Function Instructions
DVD
Mode
USB/SD
Mode
Radio
Mode
AUX
Mode
Bluetooth
Mode iPod
Mode
SEL /
On/Off
Volume +/-
Eject
Mode
Switch
Mute
Next Song
Previous
Song
45
第一 安全注意事项
第二 温馨提示
第三 面板按键操作说明
第四 主界面功能操作
第五 DVD功能操作
1、隐藏按钮功能
2、碟片播放
3、搜索播放
4、JPEG文件播放
5、CD/MP3/WMA碟片
第六 USB/SD/iPod功能操作
第七 收音机功能操作
第九 外部输入功能操作
第十 蓝牙功能操作
第十二 日历/时钟设置
第十三 设置功能操作
1、通用设置
2、触摸屏校正
3、方向盘设置
4、使用出厂设置
5、收音机设置
6、蓝牙设置
7、视频设置
8、音效设置
9、媒体设置
10、iPod设置
11、多顔燈設置
第十四 遥控器操作
第十五 注意事项
第十六 故障排除
第十七 產品參數
SEL /
On/Off
SEL /
On/Off
SEL /
On/Off
SEL /
On/Off
SEL /
On/Off
Volume +/- Volume +/- Volume +/- Volume +/- Volume +/-
Eject Eject Eject Eject Eject
Mode
Switch
Mode
Switch
Mode
Switch
Mode
Switch
Mode
Switch
Mute Mute Mute Mute Mute
Next Song Next Radio Next Song Next Song Next Song
Previous
Song
Previous
Radio
Previous
Song
Previous
Song
Previous
Song

67
V DVD Functional Operations
IV Main Interface Functional Operations
This vehicle multimedia player provides DVD, Radio, Bluetooth, SD, USB , iPod and AUNX
in functions, and related functional operations could be realized via clicking all functional
icons on main interface directly. Under all play modes, click upper right corner of the touch
screen to return to main interface.
Button Number
1. Click “ ” icon to enter iPod play
2. Click “ ” icon to enter DVD function.
3. Click“ ” icon to enter Radio function.
4. Click “ ” icon to enter Bluetooth
5. Click “ ” icon to enter USB function.
V DVD Functional Operations
1. Secrect button function
For convenient operation of users, secrect button function is particularly designed in this
vehicle multimedia system. Under DVD play mode, there are namely nine secrect touch
areas. As shown in the following figure:
1 2 3
4
7
5
8
6
9
<DVD secrect Button> Table
Button Number
1
2
3
4
5
6
7
8
9
Return to Main Interface
Pop up Search Menu
Enter Setting Interface
Previous Song
Pop up DVD Function Button
Next Song
Fast Rewind
Pause/Play
Fast Forward
Note: Please use standard original DVD, keep DVD clean, form sound use habits, and
guarantee normal use life of this vehicle multimedia system.
Function Instructions
6. Click “ ” icon to enter SD play function.
7. Click “ ” icon to enter AUX in function.
8. Click “ ” icon to enter date function.
9. Click “ ” icon to enter night mode
10. Click “ ” icon to adjust screen brightness.
11. Click “ ” icon to enter page up/down function.
12. Click “ ” icon to replace screen background.
13. Click “ ” icon to enter setting function.
Function Instructions

89
2. DVD Play
1:During DVD play, click (5) icon in the center of the touch screen, to pop up <DVD> play button.
2: Click (5) icon in the center of the touch screen again, to close <DVD> play button.
3: If you do not operate <DVD> play button for 10 seconds, system will exit automatically
1
2
3
4
5
6
7
8 9 10 11 12 13 14 15
Button No
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
<DVD> play button table P1
Discs
Volume+
Volume-
Screen off
Settings
Display Current Play Information
Sound Effect Setting
Play/Pause
Stop
Previous Song
Next Song
Fast Reverse
Fast Forward
Enlarge
Enter P2
Click “ ” icon to enter P2 play button , as shown in the following figure.
1 2 3 4 56 7 8
1
2
3
4
5
6
7
8
Repeat
A-B Repeat
Sound Track/Language Switch
Subtitle Switch
Return to Disc Main Menu
Return to Disc Subtitle Menu
Angle Shift (requires disc support)
Enter P1 Menu
Function Instructions <DVD> play button table P2
Button No Function Instructions

10 11
3. Search Play
1: During disc play, click bottom at up right corner (area A) of the touch screen, to pop up
<Search Play> menu.
2: Click “ ” icon, to close <Search Play> menu.
3: If you do not operate for 10 seconds, system will exit <Search Play> menu automatically,
as shown in the following figure:
1
2
3
4
5
6
7
Search Title
Search Chapter
Search Time
Exit <Search Play Button> Menu
Confirm Search
Number Key
Delete an input number
Example: Play program at the 30th min.
1:Click the bottom at up right corner (area A) of the touch screen, to pop up <Search Play> menu.
2:Click “ ” icon, input 3000, and then click “ ” icon to confirm, system will go to a specified
position automatically to play.
1
2
3
4
5
6 7
4. JPEG Play
This multimedia system supports picture files of JPEG format, you could
appreciate beautiful pictures via screen.
1
2
3
456 7 8 910 11
1
2
3
4
5
6
7
8
9
10
11
Click USB icon to return to main menu
Click to enter setting menu
Display current picture information
Play/Pause
Stop
Previous picture
Next picture
Enlarge
Switch effect
Picture browse
Video Search
Title：
Chapter：
Time：
Button No
<Search Play> button table
Function Instructions
Button No
<JPEG Play Button> Table
Function Instructions
Rotate picture ( can rotate 90 degrees, 180 degrees,
270 degrees and 0 degree)

12 13
5. DVD/MP3/WMA Discs
<DVD/MP3/WMA Play Button> Table
1
2
3
4
5
6
7
8
9
10
Return to main menu
Content function
Stop
Previous song
Pause/Play
Next song
Scan play
Small keyboard for song selection
Repeat play
Random play
1
2 3 4 56 7 8
9
10
1
2
3
4
Keyboard
Exit <Search Play Button> menu
Back Space
Enter
DVD
Repeat：all
Mode：common
Song：
Button No Function Instructions
Click the song to enter song selection keyboard
USB/SD supported play formats: MP3/WMA/JPGE/MPEG video.
Button No Function Instructions

14 15
VI USB/SD/iPod Function Operations
1: USB/SD/iPod supported play formats: MP3/WMA/JPEG/MPEG video.
● Under main menu, touch “ ” icons to enter USB-SD-iPod function.
● Under other statuses, insert USB-SD-iPod device, to enter USB-SD-iPod function
automatically.
● Touch <USB-SD-iPod> menu “ ” icon to exit USB-SD-iPod function.
● Plug off USB-SD-iPod device, to exit USB-SD-iPod function automatically.
Note: In playing MP3/WMA format, refer to (DVD/MP3/WMA disc play) for operation.
In playing JPEG format, refer to (JPEG play) for operation.
In playing MPEG format, refer to (DVD disc play) for operation.
Basic Operations
Enter/exit <Radio> function operations
● Under main menu, touch “ ” icon to enter Radio function.
● Touch Radio menu “ ” icon to exit Radio function.
1
2
3
4
5
6
7
8
9
10
11
12
13
Return to main menu
Main menu
Current Channel
Band switch
Auto scan channel and save
Semi-auto search radio towards low level frequency
Semi-auto search radio towards high level frequency
Open/close RDS function
Browse full-band radio
Long/short range switch
AF auto frequency adjust
PTY program type
TA enable traffic alarm
1
2
45
6 7
8
9
10
11
12
13
VII Radio Function Operations
Button No Function Instructions
<Radio Function Button> Table

16 17
Channel Search
Select FM/AM band
Click “ ” button of Radio interface, band will switch between FM1/FM2/FM3/AM.
Semi-auto search radio
Click“ ”button of Radio interface, system will search signals towards high level
frequency automatically, when it finds strong signals of a radio or a good working
station, it will stop searching immediately, or you could click this button again to stop searching.
Click“ ” button of Radio interface, system will search signals towards low level frequency
automatically, when it finds strong signals of a radio or a good working station, it will stop
searching immediately, or you could click this button again to stop searching.
Select preset channel to play
Select the band required , and click the radio preset in Radio interface to play.
Save channel manually
Select the band required, and then search channel, stop at the frequency required,
and select frequency display bar of the radio No. expected to be saved, press it for
3 seconds, this radio will save at the specified position.
Local search mode (LOC)
When local search function LOC is on, only radio stations with sufficient signals and sound
receiving status could be searched, when local search function is enabled, DX icon displayed
on the screen will become LOC.
IX External Input Function Operations
Enter/Exit <External Input> function operations
●Under main menu, touch “ ” icon to enter External Input function.
●Touch External Input menu “ ” icon to exit External Input function.
Basic operations
Enter/Exit <Bluetooth> function operations
●Under main menu, touch “ ” icon to enter Bluetooth function.
●Touch External Input menu “ ” icon to exit Bluetooth function.
1
2
3
4
5
6
7
8
9
10
<Bluetooth Dial Function Button> Table
1
2
3
4
5
6
7
8
9
10
Return to main menu
Back Space
keyboard/* & # key
Answer
Hang off
Switch between mobile and Bluetooth
Phonebook
Dial Board
Bluetooth music
Paired Mobile
X Bluetooth Function Operations
Function Instructions
Button No Function Instructions

18 19
2
3
4
5
68
7
1
<Bluetooth Contacts Button> Table
1
2
3
4
5
6
7
8
Return to main menu
Answered calls
Missed calls
Dialed calls
SIM storage
Mobile storage
Page up
Page down
1
2 3 4
1
2
3
4
Return to main menu
Previous Song
Play/Pause
Next Song
1. Bluetooth Function User Manual
1:Pairing
After entering Bluetooth status, click “Pairing” icon, open the mobile bluetooth function to
search devices, and then choose " connection" when Bluetooth of this product is searched
(Bluetooth device name of this machine is Milion), connect and input matching password
“5802”, after matching succeeds, Bluetooth icon will display on top of the screen.
Bluetooth connection status icon instruction:
1.When icon flashes, it indicates no Bluetooth device is connected.
2.When icon keeps displaying, it indicates Bluetooth device has been connected.
2: Dial
Method: 1 When pairing succeeds, click keypad and input phone numbers, and then click
“dial” icon to make a call.
Method: 2 When matching succeeds, dial with mobile, Bluetooth interface will pop up
automatically.
3: Answer calls
After matching succeeds, when there’re incoming calls, in any Modes, system will go to
Bluetooth status automatically, click “Answer” icon to answer calls.
4: Ring off
Click “Ring off" icon, to reject incoming calls or end calls.
5: Call switch
Click “Switch” icon in calls, to switch calls back to mobile to continue, click “Switch" icon
again, to switch calls back to machine to continue.
6: Play Bluetooth music (which could only be realized by mobile phones supporting A2DP
protocol)
After Bluetooth matches with mobile successfully, click play button in Bluetooth interface to
play Bluetooth music.
Note: For different brand designs of mobile phones, sometimes it is required to select music to
play via mobile phones, sometimes it is only required to click play button in Bluetooth
interface directly.
! For different Bluetooth modules adopted by mobile phones of different brands and difference
between applications, there may be difference in some functions during actual usage, or even
incompatibility, please forgive.
Button No Function Instructions
<Bluetooth Music Button> Table
Button No Function Instructions

20 21
Click “ ” in main menu to enter time setting interface.
<Calendar/Clock Setting> Table
1
2
3
4
5
6
7
12/24 hour shift
Shift to adjust clock status
Return to main menu
Shift to adjust date status
Adjust year/month
Confirm
Adjust date
12
3
4
56
7
Basic Operations
Enter/Exit <Setting> function operations.
●Under main menu, touch“ ” icon to enter setting status.
●Touch <Setting> menu touch“ ” icon to exit system settings.
1、General Settings
In setting menu, click “ ” to enter general settings interface.
<General Function Button> Table
1
2
3
4
5
6
7
Return to main menu
Language Selection
Key Tone setting
Screen Saver setting
Touch screen setting
Steering wheel control setting
Restore factory settings
1
2
3
4
5
6
7
XII Calendar/Clock Setting
Button No Function Instructions
XIII Setting Function Operations
Button No Function Instructions

22 23
2、 Touch Screen Calibration
① Click “Touch Screen Calibration” while setting general menu to enter touch screen
calibration interface.
② Calibration method: Align the center of “+” icon with touch pen and hold it, till “+” icon
runs to the next calibration point, repeat the previous action, and calibrate 5 points
according to sequence, and click the touch screen to exit touch screen status, if the
center of “+” icon is not aligned during calibration, it will be recalibrated, and exit touch
screen calibration status after calibration is done.
3、Steering wheel control Setting
Click “Steering wheel control Setting” in the general setting to enter setting interface.
2
34
5
6789
1
<Dashboard Button> Table
1
2
3
4
5
6
7
8
9
Return to main menu
Exit steering wheel control interface
Voltage display
Image number display
Common function buttons
Restore default value
Clean
Confirm
Set
Instruction: During Steering wheel control setting, press a single button,
button voltage value will be displayed on screen, and required button
functions could be assigned
Button No Function Instructions

24 25
4、Use Factory Settings
In general menu, click “Use Factor Settings” to enter use factory settings interface.
1
<Use Factory Settings Button > Table
1
2
3
4
Button No Function Instructions
Return to main menu
Current Operation Instructions
Restore Factory Settings
Exit Factory Settings
5、Radio Settings
In setting menu, click“ ” to enter Radio settings interface.
1
<Radio Settings Button> Table
Button No Function Instructions
1
2
3
4
5
6
7
Return to main menu
Radio region selection
RDS switch
TA option
TA adjust
Time Synchronization Switch
TA Volume Adjust
6、Bluetooth Settings
In setting menu click“ ” to enter Bluetooth settings interface
<Bluetooth Settings Button> Table
Button No Function Instructions
1
2
3
4
Return to main menu
Bluetooth switch settings
Auto connect switch settings
Auto answer switch settings
1
2
3
4
3
2
4
2
3
4
5
6
7

26 27
7、Video Settings
In setting menu click“ ” to enter video settings interface.
<Video Function Button> Table
1
2
3
Button No Function Instructions
Return to main menu
Rear mirror image setting
Brake video setting
1
8、Volume
In setting menu click “ ” to enter sound effect settings interface.
Settings
<Sound Effect Function Button> Table
1
2
Return to main menu
Volume Setting
9、Media Settings
In setting menu click “ ” to enter media settings interface.
1
2
<Media Setting Button> Table
1
2
3
4
5
6
Return to main menu
Set DVD Subtitle
Set DIVX Subtitle
Set DVD Language
Set DIV Subtitle
View Mode Selection
1
2
3
4
5
6
10、iPod Settings
In setting menu click “ ” to enter media settings interface.
<iPod Setting Button> Table
1
2
Return to main menu
Auto connect selection
1
2
2
3
Button No Function Instructions
Button No Function Instructions
Button No Function Instructions

28 29
11、Color Light Settings
This interface could set button light colors. You have seven LED colors optional or you
can close button light.
XIV Remote Controller Operation
Usage of Remote Controller
User Manual:
◆Remote controller uses CR2025 Li battery.
◆Under normal circumstances, the battery could be used for about 1 year. When the remote could not
operate normally, please replace battery in time.
◆Do not place the remote controller in high temperature or under sunshine directly, otherwise it could
not work normally.
◆During battery installation, do not install the battery in wrong direction (reverse positive + and negative -).
◆Do not take the battery with metal clamp, otherwise it will cause short circuit.
Replace Remote Controller Battery
1. Take out battery
Take the battery out from back of the remote controller according to below figure.
2 Install Battery
Use CR2025 Li battery, and put in the battery according to the following figure (place + and – correctly).
★Note: Please remove insulating plastic layer in battery buckle
of the remote controller the first time you use.
Remote Operation Instructions
1.PWR
Power switch, press this button to power on when the machine is
off, and long press this button to power off when the machine is
on, short press to Mute.
2.EQ
Long press this button to select preset sound effect mode, under
any Mode, press this button to dial or answer.
3.ANGLE/AMS
During playing Discs with angle switch function, press this button
to change view angle.
Under radio mode, long press this button to auto search and save
radio stations.
4.SUB-T/LOC
Under FM mode, press this button to select long/short range radio.
Under DVD mode, press this button to replace subtitle language.
5.PROG/A-B
Under DVD playing mode, press this button to set program play
sequence.
Under DVD/VCD Mode, long press this button to set Repeat
segments.
6.OSD/*
Under other modes, press this button to display time, front/rear
display output mode and current device (DISC/SD/USB).
Under sound play mode, press this button repeatedly to display play information.
Under Bluetooth Mode, press this button to process dial function.
7.GOTO/#
Under DVD mode, press GOTO and cursor key to select title, song name, disc sound, disc subtitle,
angle, title time, chapter time, Repeat, time display, and then press ok to enter options and set;
Under VCD mode, press GOTO and cursor key to select song, full disc time, song time, Repeat, time
display, and then press OK to enter option and set;
Under CD/MP3 mode, press GOTO to select song time “_ _；_ _” or song :_ _:XX”, and then press
0-9 number keys to select required song or time;
Under Bluetooth mode, press # key to process dial function.
8.MENU
Under DVD mode, long press this key to return to root directory of disc menu.
Under radio mode, press this key to shift to main interface.
9. Under sound play mode, select fast forward/fast rewind to play, and page up/down to select songs.
Under radio mode, search frequency, and select programs.
In DVD setting menu, use arrow keys to select file list and set catalogue, press ENTER to confirm.
10.RPT/NAV
Under sound play mode, press this key to Repeat.
Long press to enter or exit navigation mode directly.
11.PTY/LED
Under radio mode, long press this key to enable/disable PTY function.
Short press LED button to select different LED modes.
12.ZOOM/AF
Under radio mode, press this key to enable/disable AF function. During playing DVD/VD VD, press
this key to set image size.
13.SRC
Press this key to shift mode.
14.VOL-/VOL+/SEL
Press + key to increase volume, and press – key to decrease.
When no handbrake wire is connected, short press rather than long press SEL key to view videos
(valid during standby).
15. Eject Discs.
16.LOUD
Long press this key to enable/disable LOUD function.
Under Bluetooth mode, press this key to end calls.

30 31
17.(0-9) NUMBER BUTTON
Under radio mode, press number keys (1-6) to select corresponding preset radio stations; long press to
save.
Under sound play mode, press this key to select programs or songs directly.
Under Bluetooth mode, it is a telephone number input key.
18.CLEAR
Clear and key in correct number when a wrong number is input.
19. Press this key to pause and press again to play.
20.TITLE
Under DVD mode, press key to return to title menu.
Under VCD mode, press this key to enable/disable PBC function.
21. Press this key to stop playing
22. BAND/PN
Under radio mode, press this key to switch bands.
Under DVD/VCD mode, press this key to select output mode.
23. SETUP
Press this key to enter DVD setting.
24. AUDIO/ST
Under DVD mode, press this key repeatedly to select audio language.
Under VCD mode, press this key repeatedly to select sound track mode.
Under radio mode, press this key to select stereo or mono sound track.
25. RDM/TA
Long press this key to enable/disable TA function. Under radio mode, press this key to play at random.
XV Notices
1. Machine Use Notices
Do not insert hard objects or other metal materials into the machine.
Do not try to repair. This display screen is composed of multiple precise electronic
components, and any dismantlement may damage it, if there’s any problem, shut down the
power immediately, and inform our company or related dealers.
Keep the display screen away from humidity, dust, steam and smoke etc.
Do not use diluents or other chemical detergents to wipe display surface; use soft cloth to wipe
off dirt on the surface.
Keep the display away from longtime disposure to the sun.
If there’s water or any other impurity penetrating into the machine, cut off power immediately,
and contact our company or related dealers.
During cleaning, please power off first.
Design of this product is for vehicle equipped with 12V negative grounded storage battery
system.
2. Disc Use Notices
Dirty, dusty, scrached or bent Discs may cause misoperation.
Do not put discs on sharp objects, to prevent from being scrached.
When not in use, eject disc.
Do not put discs in the following positions:
1.Places exposed to direct sunshine.
2.Places with dirt, dust and humidity.
3.Places near vhechile heater.
4.Vhechile seats or dashboards.
Do not use discs with a diameter under 12cm (excluding 12cm) or discs of irregular shapes
(heart shape or octagon etc.)
Clean discs: Use wet cloth to wipe disc surface; if there's too much dirt, use soft cloth soaked
with warm polyalcohol to wipe gently. Do not use solutions such as gasoline or diluents etc., to
prevent any damage to disc surface.
3. External Amplifier Setting Notices
Please check whether speaker resistance matches optimal resistance or not before
connection.
Please use speaker wire of high quality, and wire length shall exactly fits.
While connecting signal wire, sound track ports shall correspond, and not misconnection is
allowed.
In order to reduce noise, when there’s any external amplifier connected, tune machine volume
to 1/3 of the max. volume, and tune volume of external amplifier, till sound distortion
(Note: Volume adjustment shall be proper).
During installation, input/output wire shall be kept away from power and vehicle wire,
otherwise, there will be noise.
XVI Troubleshooting
Before sending the machine for repair, refer to the following table with respect to
possible reasons, and adopt corresponding solutions to carry out simple check or
minor adjustment, to do troubleshooting, and make the machine restore normal
operation. If you could not solve problems according to methods listed in the table,
please contact our company or professional repair center.
No display on
LCD screen
Unable to play sound
Unable to play pictures
Occasional sound
jump
Bluetooth invalid
Issues
Possible Reasons
Solutions
Power and igniter switch not connected Power on
Loosen connection wire Reconnect
Burnt fuse Replace a new fuse
System is under mute status Press mute to close
Loosen speaker connection Reconnect
Damaged speaker Replace a new speaker
Incorrect disc placement Place disc with label face
up on tray
Dirty or damaged discs Use other discs
Sound jump during
vibration
Dirty or damaged discs Use other discs
Incorrect installation of the machine Guarantee firm installation
of the machine
Fastening installation bolts of discs
in the wrong direction
Put angle tuning bolts
marked with V or H in
correct installation direction
Unmatched with the machine
correctly Rematch

32
XV Product ParametersII
WARNINGS
Caution: Please operate according to instructions before usage;
This machine is made of precise parts, please guard against damp;
For high pressure inside the machine, dismantlement could only be
carried out by authorized persons;
Special Tips: For your safety, please do not watch movies during driving,
please turn down the screen.
Special Notes: Few color spots may appear in LCD screen, which is a
common phenomenon in matrix
display technology, and does not represent any defect or failure.
Thanks for your usage