Milly and Coup Pixi User manual

IMPORTANT! READ CAREFULLY
AND KEEP FOR FUTURE REFERENCE
Newborn Parent Facing Pack
Product Manual
Pixi

Age & weight limits:
• Maximum age and weight limit for a child in the Newborn Parent Facing Pack
is 22kg, although we recommend this be used from newborn to 6 months.
General safety:
• This newborn pack is approved for use with the Milly + Coup Pixi range only.
Do not use with any other products.
• Always ensure the newborn pack is securely attached before using the stroller.
• Ensure the harness is fastened at all times while your child is in the stroller.
• Supervise your baby at all times.
• Do not use for unsupervised sleeping.
• Never leave the UV cover over the stroller indoors, in a hot atmosphere or near
a heat source.
Tips to avoid tears
Pixi Product Manual
The Pixi Newborn Parent Facing Pack is designed and tested to comply with
Consumer Protection Notice No. 8 of 2007, AS 2088:2022 and AS/NZS ISO 8124-3.
• DO NOT USE THIS SEAT WITH ANY OTHER MODELS OF STROLLER.
2

Pixi Product Manual
What’s in the box?
Base
Canopy
UV / Sun Cover
1
2
3
Parts Checklist
Please check that you have all the correct
parts before getting started.
1 2
3
3

Ensure the seat is in the fully upright
position and remove the belly bar.
Behind the canopy, undo the elastic loops
connecting the canopy to the frame on
either side of the handlebar.
Lift the leg rest fully upright to meet the
seat backrest so that you can access the
underside of the seat.
Undo the zip wrapped around the metal
bar.
To remove the canopy, press the button on
the outside of the canopy connectors (A)
and pull out from the frame.
Below the canopy connectors are the
seat connectors (B). To remove these
press the release tab on the inside of the
connectors and then pull them out.
Undo the strap below the zip and
un-thread each end out through the
slots in the plastic.
4
Pixi Product Manual
Removing the stroller seatRemoving the stroller seat
A
B

You’re now ready to attach
the newborn pack!
You can then pull the seat fabric upwards
and o the frame.
Note: There is a fabric slip (A) that keeps
the seat on the frame, this may get stuck
as you try to lift o the seat. Simply guide
it over the footrest levers to release.
5
Pixi Product Manual
Removing the stroller seat
A

Starting with the frame in the position
shown, fold the newborn pack in half ensuring
the harness is facing towards the handlebar
(it is a parent facing seat).
Slide the fabric slip over the footrest levers
and onto the metal frame.
Pull the end of the strap with the Velcro
through the ring on the end of the other
strap and fasten together.
Pull the head end of the base down firmly
so that you feel it lock into place on the
frame.
Thread both straps through the slots on
the plastic.
Pixi Product Manual
Attaching the newborn packAttaching the newborn pack
6
Wrap and secure the small Velcro strap
that is on the underside of the seat
around both the thin metal bar and the
thick plastic bar of the stroller frame.
Note: you may need to flip the stroller to
be able to access underneath.

At the other end of the base, secure the
seat connectors into the plastic connector
slots on both sides of the frame.
Note: Ensure you connect these into the
lower of the two slots.
Note: these are the same slots that the
belly bar would normally slot into for the
stroller seat.
To attach the canopy, place the elastic
end of the canopy over the head end
of the base and secure underneath the
base using the Velcro. Secure each of the
canopy connectors to the upper slots on
both sides of frame.
To fold the canopy, grip the middle
canopy rod and pull down to avoid
excess fabric in the top of the base.
Your newborn pack is now
set up and ready to go!
Pixi Product Manual
Attaching the newborn pack
7
• ALWAYS SECURE YOUR CHILD IN THE HARNESS WHEN
USING THE NEWBORN PACK.

8
Pixi Product Manual
Removing the newborn packFolding with the newborn pack
Pixi can be folded with the newborn pack attached.
Pull the entire canopy and base back up to
meet the handlebar.
Simultaneously push the lock button (A) and
the release button (B) while pushing the
handlebar forward so that the stroller folds
onto itself.
Ensure the frame lock has engaged
before lifting and carrying.
When carrying the stroller, grasp the
handle and avoid lifting with a bent back.
A
B
Undo the Velcro strap from underneath that
is connecting the underside of the seat to
the stroller frame.

9
Press the button on the sides of the
canopy connectors before pulling
them out to remove the canopy.
Press the button on the inside
of the seat connectors and pull them
out of the sockets.
Undo the Velcro strap and un-thread it
back through the slots in the plastic as
shown.
While holding both ends of the newborn
pack, pull it up and o the frame.
Pixi Product Manual
Removing the newborn pack
Undo the Velcro of the small strap that is
wrapped around the stroller frame and
lift the seat upwards to release it from the
frame.

10
Pixi Product Manual
Re-attaching the stroller seat Re-attaching the stroller seat
Start with the frame in the position shown.
Secure the canopy connectors into
the upper connectors slots on both
sides of the frame.
Behind the seat, secure the elastic
loops on each side of the canopy
to the handlebar frame.
Attach the seat connectors below the
canopy connectors into the lower slots.
Lift the base of the frame up towards
the handlebar and slide the seat’s
fabric slip over the footrest levers and
all the way down the frame.
Click!
1
2

11
To attach the UV cover
Pixi Product Manual
Re-attaching the stroller seat
Next, thread each Velcro strap through
the slots in the plastic attachment arms.
Pull the strap with the Velcro end, through
the other straps’ metal buckle and secure
them together.
Secure and close the zip around the
metal bar.
Pull the seat base and footrest firmly
down and secure it in place on the frame.
Insert the belly bar to the frame.
Make sure you thread the footrest levers
through the holes in the fabric. It should
now look like the image shown.
Place the elasticated edge of the UV cover
over the edge of the canopy and secure the
toggle on each end through the loop on the
side of the canopy.
Attach the elastic loops on the opposite end
of the UV cover to the round clips on the
frame underneath the handlebar.

Contact Us:
[e-mail] | [e-mail]
Model: Pixi Newborn Parent Facing Pack Version: 1 - March 2023
Information subject to change. Please see website for current version.
millyandcoup.com