RH Baby&child WILKES TODDLER BED CONVERSION KIT INST User manual

WILKES TODDLER BED CONVERSION KIT INSTRUCTIONS
CUSTOMER SERVICE
If you are missing parts or have any questions about this product, contact us first. You can also order parts by writing to the address above. Include
the product model number, color, and a brief description of the part. Call 1-800-762-1751.
CARE AND CLEANING
DO NOT scratch or chip the finish. DO NOT use abrasive chemicals for cleaning. Dust often using a clean, soft, dry cloth.
Blot spills immediately and wipe with a clean damp cloth. If the crib is to be stored, store in a cool dry place and carefully package all original
hardware to protect from loss.
TOOLS AND INSTALLATION
Tools Necessary: Allen Key (included)
NOTE: It may be easier to assemble product with two people.
NOTE: When inserting bolts, turn clockwise until tight. Then loosen 12- 34of a turn. After crib is completely assembled, return to each bolt and
tighten. Use wax or soap on all bolts to facilitate assembly
WARNING: Read all
instructions before assembling this
product. KEEP INSTRUCTIONS
FOR FUTURE USE.
Page 1 of 7
All Restoration Hardware cribs are designed to meet the highest safety
standards and comply with all U.S. and Canadian cribs and cradles regulations.
Made in Vietnam
Distributed in the U.S.A. by:
Restoration Hardware Baby & Child
2900 North Macarthur Dr. Tracy,
CA95376, USA
www.rhbabyandchild.com
Distributed in Canada by:
Restoration Hardware Canada, Inc.
1500-1055 West Georgia Street
Vancouver, British Columbia V6E4N7

Page 2 of 7
IMPORTANT SAFETY INFORMATION FOR TODDLER & DAY BEDS
·The mattress intended for use on the bed shall be a full-size crib
mattress having minimum dimensions of 51-5/8 inches (1310mm) in
length, 27-1/4 inches (690mm) in width and 4 inches (100 mm) in
thickness, not exceeding 6 inches (152 mm) in thickness.
·If guardrails are used as the mattress containment means,
guardrail(s) provided must be used to avoid the formation of a gap
between the mattress and the bed that could cause an entrapment.
·DO NOT place bed near windows where cords from blinds or drapes
may strangle a child.
·DO NOT place items with a string, cord, or ribbon around a child’s
neck, such as hood strings or pacifier cords.
·DO NOT suspend strings over a toddler bed for any pacifier cords.
·A child using the toddler or day bed shall be at least 15 months of age
and shall not weigh more than 50lbs (22.7kgs).
WARNING: ENTRAPMENT / STRANGULATION HAZARD
Infants have died in toddler beds from entrapment and strangulation.
Failure to follow these warnings and the assembly instructions could
result in serious injury or death.
NEVER use bed with children under 15 months.
NEVER place bed near windows where cords from blinds or drapes
may strangle a child.

Page 3 of 7
WARNING: ADULT ASSEMBLY ONLY, OWING TO THE PRESENCE OF
SMALL PARTS, SHARP POINTS AND EDGES.
CAUTION
TODDLER BED: THE MINIMUM AGE SHALL NOT BE LESS THAN 15 MONTHS AND THE MAXIMUM
WEIGHT SHALL NOT BE GREATER THAN 50LBS. (22.7 KG).
THE MATTRESS INTENDED FOR USE ON THE BED SHALL BE A FULL-SIZE CRIB MATTRESS HAVING
MINIMUM DIMENSIONS OF 51-5/8 IN. (1310MM) IN LENGTH, 27-1/4 IN(690MM)IN WIDTH AND 4 IN. (100MM)
IN THICKNESS NOT EXCEEDING 6 IN. (152MM) IN THICKNESS.
CARE INSTRUCTIONS:
·Dust often using a clean, soft, dry, lint- free cloth.
·Blot spills immediately, and wipe with a clean, damp cloth.
·We do not recommend the use of chemical cleaners, abrasives, or furniture polish on our lacquered finish.
TODDLER CONVERSION KIT
ASSEMBLY HARDWARE IS
INCLUDED IN THE TODDLER
KIT BOX.
ALLEN WRENCH = 1 PC
(EE) 1/4" X 1/2" BOLT = 2 PCS
SIDE RAIL PANEL
HEADBOARD
TODDLER RAIL
MATTRESS SUPPORT

Page 4 of 7
ASSEMBLY INSTRUCTIONS
STEP #1. FRONT RAIL PANEL DISASSEMBLY
STEP #1.1:
Remove the front rail panel of the crib by loosening all the bolts
installed, as in DETAIL A.
STEP #1.2:
Gently tilt the crib and release the bolts underneath the metal
brackets holding the stabilizer rails, as in DETAIL B.
NOTE: Slightly loosen the bolt at the back of the headboard that
enough to set the toddler rail in-between side rail panels.
A
A
A
A
DETAIL A
DETAIL B
(CC)
(DD)

Page 5 of 7
STEP #2.
TODDLER RAIL ASSEMBLY.
STEP #2.1
On inside face of both side rail panels there is a cavity for the
hook and a pre-installed nut for the Allen bolt to pass through,
which corresponds to the hooks on both ends of the toddler rail
and hole with holes pre-drilled. Align and insert the hook of the
toddler rail into the cavity of the side rail panel, then engage
Allen head bolt (removed from step #1.1) in the hole and tighten
with Allen wrench provided. See DETAIL C.
STEP #2.2
Fill the holes located on the top of the side rail panel by inserting
bolt (EE) provided. (DETAIL D)
(DD)
METAL
HOOK
DETAIL C
D
DC
C
(EE)
DETAIL D
HARDWARE
(EE) 1/4" X 1/2" BOLT = 2 PCS
ALLEN WRENCH = 1 PC
METAL
HOOK

Page 6 of 7
B
C
STEP #3
MATTRESS SUPPORT HEIGHT ADJUSTMENT
DETAIL F
MATTRESS
SUPPORT
STABILIZER RAIL
HARDWARE
LOCK
WASHER
HEX NUT
PLAIN
WASHER
ALLEN BOLT
(BB)
ALLEN
WRENCH
DETAIL E
ALLEN BOLT
(BB)
ALLEN BOLT
(BB)
ALLEN BOLT
(BB)
LOCK WASHER = 8 PCS
PLAIN WASHER = 8 PCS
HEX NUT = 8 PCS
11 X 70
OPEN WRENCH = 1 PC
ALLEN WRENCH = 1 PC
NOTE: If mattress supports is not in the lowest position.
STEP #3.1
Loosen and remove all hardware (BB) on both sides of the frame of
mattress support.
STEP #3.2
Re-install the bolt on the third hole of the frame through the hole on the
arm support. Fasten the bolt with plain washers, lock washers &
hexagonal nut. Repeat procedure on the other arms of the mattress
support. See DETAIL E & DETAIL F.
(BB) 1/4" X 1-3/8" BOLT = 8 PCS

Page 7 of 7
STEP #4
INSTALLATION OF STABILIZER RAILS
INTO THE SIDE PANEL
STEP #4.1
On inside face of both side rail panels are pre-installed metal
brackets, designed to hold the stabilizer rails. Set both ends of
the stabilizer rails into brackets, as illustrated in DETAIL G.
STEP #4.2
Once the stabilizer rails are set, gently tilt the toddler bed and
fasten the stabilizer rails with bolt, plain washer and lock
washer, as illustrated in DETAIL H.
NOTE
After assembly, re-tighten all bolts to a snug fit.
DETAIL G
(CC)
DETAIL H