Mimosa 0082322 User manual

OUTDOOR GAS HEATER
TALL FLAME-MATTE BLACK
Provides warmth and ambiance for outdoor settings
AGA Gas Certified
Important: Please retain these instructions for future use
0082322
0082322 GFH004

Gas connections on the heater are leak tested at the factory prior to shipment. A complete gas
tightness check must be performed due to possible mishandling in shipment or excessive pressure
being applied to the heater gas connections.
1.Make a soap solution of one part liquid detergent and one part water.
Make sure the control knob on the heater is off and the gas valve on the cylinder is off before
mixing the soapy solution.
2.Turn on the gas bottle.
3. Apply the soap solution to the gas connections using a soft bristle brush.
Soap bubbles will appear
if there is a gas leak.
In case of a leak, turn off
the gas supply. Tighen any
leaking fittings, then turn the
gas supply on and re-check.
If there is a leak anywhere
on the gas cylinder, do not
use the cylinder. Locate the
leaking cylinder outdoors
away from sources of
ignition, then contact your
local gas authority or
cylinder exchange provider
to arrange disposal.
Warning：
Do not operate the appliance until all gas leaks have been rectified.
Never leak test while smoking.
+++
+
+
+
Regulator / Cylinder
Hose / Regulator
Detergent
Gas Leak Test

7KLVDSSOLDQFHPXVWEHLQVWDOOHGLQDFFRUGDQFHZLWKWKHPDQXIDFWXUHUVLQVWDOODWLRQ
LQVWUXFWLRQVORFDOJDVILWWLQJUHJXODWLRQVPXQLFLSDOEXLOGLQJFRGHV$6*DV
,QVWDOODWLRQVDQGDQ\RWKHUVWDWXWRU\UHJXODWLRQV
5HDGWKHLQVWUXFWLRQVEHIRUHLQVWDOODWLRQDQGXVH
7KLVDSSOLDQFHPXVWEHLQVWDOOHGDQGWKHJDVF\OLQGHUVWRUHGLQDFFRUGDQFHZLWKWKH
UHJXODWLRQVLQIRUFH
7KLVDSSOLDQFHUHTXLUHVLQVWDOODWLRQE\DFRPSHWHQWSHUVRQ
)RUXVHRQO\LQZHOOYHQWLODWHGDUHDV$YHQWLODWHGDUHDPXVWKDYHDPLQLPXPRI
RIWKHVXUIDFHDUHDRSHQ7KHVXUIDFHDUHDLVWKHVXPRIWKHZDOOVVXUIDFH
7KHXVHRIWKLVDSSOLDQFHLQHQFORVHGDUHDVFDQEHGDQJHURXVDQGLVSURKLELWHG
7KLVDSSOLDQFHPXVWQRWEHXVHGLQGRRUV
7KLVDSSOLDQFHPXVWEHXVHGIRUVSDFHKHDWLQJRQO\
7KLVDSSOLDQFHPXVWQRWEHXVHGLQEDVHPHQWVRUEHORZJURXQGOHYHO
7KLVDSSOLDQFHLVIRURXWGRRUXVHRQO\
8VHRQO\WKHW\SHRIJDVDQGWKHW\SHRIF\OLQGHUVSHFLILHGE\WKHPDQXIDFWXUHU
'RQRWSODFHLWHPVRQRUDJDLQVWWKLVDSSOLDQFH
'RQRWVWRUHFKHPLFDOVRUIODPPDEOHPDWHULDOVRUVSUD\DHURVROVQHDUWKLVDSSOLDQFH
'RQRWRSHUDWHWKLVDSSOLDQFHLQDQH[SORVLYHDWPRVSKHUHOLNHLQDUHDVZKHUHSHWURO
RURWKHUIODPPDEOHOLTXLGVRUYDSRUVDUHVWRUHG
3URWHFWWKHKRWJODVVWXEHIURPUDLQZDWHUVSODVKRUDQ\WKLQJWKDWZLOOFDXVHDVXGGHQ
FKDQJHLQWHPSHUDWXUHZKLFKPD\OHDGWRFUDFNLQJRUVKDWWHULQJ
WARNING
WARNING
WARNING
WARNING
7XUQRIIWKHJDVYDOYHLPPHGLDWHO\LIWKHVPHOORIJDVLVGHWHFWHG
([WLQJXLVKDQ\RSHQIODPH
,IRGRXUFRQWLQXHVFRQWDFW\RXUJDVVXSSOLHULPPHGLDWHO\
WARNING
7+($33/,$1&(0867127%(86(',)7+(*/$6678%(,6'$0$*('25127
/2&$7(',1,76&255(&7326,7,21
DANGER
,)7+($33/,$1&(,67,33('29(57+(*/$6678%(&$16+$77(5,1
6+$53('*(')5$*0(176
&HUWDLQPDWHULDOVRULWHPVZKHQVWRUHGXQGHURUQHDUWKHDSSOLDQFHZLOOEHVXEMHFWHGWR
UDGLDQWKHDWDQGFRXOGEHVHULRXVO\GDPDJHG
7KHXVHUDVVXPHVDOOULVNLQWKHDVVHPEO\DQGRSHUDWLRQRIWKHJDVKHDWHU
)DLOXUHWRIROORZWKHZDUQLQJVDQGLQVWUXFWLRQVLQWKLVPDQXDOFDQUHVXOWLQVHYHUHSHUVRQDO
LQMXU\GHDWKRUSURSHUW\GDPDJH,IXVHUFDQQRWUHDGRUIXOO\XQGHUVWDQGWKHLQVWUXFWLRQ
PDQXDOSOHDVHFRQWDFW\RXUGHDOHU0DQXIDFWXUHURUVXSSOLHUZLOOQRWEHUHVSRQVLEOHIRU
XVHUVQHJOLJHQFH
7KLVSURGXFWFRQWDLQVDVPDOOEDWWHU\6ZDOORZLQJWKHVPDOOEDWWHU\FDQFDXVH&+2&K,1*
+$Z$5'6HHNLPPHGLDWHPHGLFDODWWHQWLRQLIWKHEDWWHU\LVVZDOORZHGRULQKDOHGKHHS
FKLOGUHQDZD\IURPWKHVPDOOEDWWHU\
WARNING

Table Of Contents
Caution...........................................................Page1
Heater Location.............................................Page2
Gas Requirements.........................................Page4
Leakage Test................................................... Page4
Operation and Storage.................................Page5
Cleaning and Care.......................................Page6
Parts and Specifications ...............................Page6
Assembly Parts..............................................Page8
Assembly Steps.............................................Page10
Pilot Service....................................................Page17
Problems Check List......................................Page20
Product Warranty...........................................Page21

PLEASE READ CAREFULLY THE FOLLOWING SAFETY GUIDELINES BEFORE OPERATION.
7KLVSDWLRKHDWHULVQRWIRUFRPPHUFLDOXVH
7KLVIODPHKHDWHULVIRURXWGRRUXVHRQO\VHHDWWDFKHGGLDgUDPPDWLFDOUHSUHVHQWDWLRQVRIRXWGRRUDUHDV
7KLVRXWGRRUKHDWHULVQRWLQWHQGHGWREHLQVWDOOHGRQUHFUHDWLRQDOYHKLFOHVDQGRUERDWV
'RQRWXVHWKHKHDWHUIRUWKHKHDWLQJRIGRPHVWLFSUHPLVHV
'RQRWXVHWKHKHDWHULQWKHEDVHPHQWVRUEHORZJURXQGOHYHO
7KLVDSSOLDQFHPXVWEHLQVWDOOHGDQGWKHJDVF\OLQGHUVWRUHGLQDFFRUGDQFHZLWKWKHUHJXODWLRQVLQIRUFH
,QVWDOODWLRQDQGUHSDLUVKRXOGEHGRQHE\DTXDOLILHGVHUYLFHSHUVRQ
,PSURSHULQVWDOODWLRQDGMXVWPHQWDOWHUDWLRQFDQFDXVHSHUVRQDOLQMXU\RUSURSHUW\GDPDJH
'RQRWDWWHPSWWRDOWHUWKHXQLWLQDQ\PDQQHU
1HYHUUHSODFHRUVXEVWLWXWHWKHUHJXODWRUZLWKDQ\UHJXODWRURWKHUWKDQWKHIDFWRU\VXJJHVWHGUHSODFHPHQW
5HPRYHWUDQVLWSURWHFWLRQEHIRUHXVH
'RQRWVWRUHRUXVHSHWURORURWKHUIODPPDEOHYDSRUVRUOLTXLGVLQWKHKHDWHUXQLW
7KHZKROHJDVV\VWHPKRVHUHJXODWRUSLORWRUEXUQHUVKRXOGEHLQVSHFWHGIRUOHDNVRUGDPDJHEHIRUHXVH
DQGDWOHDVWDQQXDOO\E\DTXDOLILHGVHUYLFHSHUVRQ
7KHUHFRPPHQGHGIUHTXHQF\RIFKHFNLQJWKHWXELQJRUWKHIOH[LEOHKRVHLVDWOHDVWRQFHSHUPRQWKDQGHDFK
WLPHWKHF\OLQGHULVFKDQJHG,ILWVKRZVVLJQVRIFUDFNLQJVSOLWWLQJRURWKHUGHWHULRUDWLRQLWVKDOOEHH[FKDQJHG
IRUQHZKRVHRIWKHVDPHOHQJWKDQGRIIWKHHTXLYDOHQWTXDOLW\DVVSHFLILHGE\WKHPDQXIDFWXUHU
7KHWXELQJRUWKHIOH[LEOHKRVHPXVWEHFKDQJHGZLWKLQWKHSUHVFULEHGLQWHUYDOV
$OOOHDNWHVWVVKRXOGEHGRQHZLWKDVRDS\ZDWHUVROXWLRQ1HYHUXVHDQRSHQIODPHWRFKHFNIRUOHDNV
'RQRWXVHWKHKHDWHUXQWLODOOFRQQHFWLRQVKDYHEHHQOHDNWHVWHG
7XUQRIIWKHJDVYDOYHLPPHGLDWHO\LIVPHOORIJDVLVGHWHFWHG
'RQRWWUDQVSRUWWKHKHDWHUZKLOHLWVRSHUDWLQJ
'RQRWPRYHWKHKHDWHUDIWHULWKDVEHHQWXUQHGRIIXQWLOWKHWHPSHUDWXUHKDVFRROHGGRZQ
6KXWRIIWKHYDOYHDWWKHJDVF\OLQGHURUWKHUHJXODWRUEHIRUHPRYLQJWKHDSSOLDQFH
8VHRQO\WKHW\SHRIJDVDQGWKHW\SHRIF\OLQGHUVSHFLILHGE\WKHPDQXIDFWXUHU
,QFDVHRIYLROHQWZLQGSDUWLFXODUDWWHQWLRQPXVWEHWDNHQDgDLQVWWLOWLQJRIWKHDSSOLDQFH
.HHSWKHYHQWLODWLRQRSHQLQJRIWKHF\OLQGHUHQFORVXUHIUHHDQGFOHDURIGHEULV
'RQRWSDLQWWKHIOXHVFUHHQZLQGVKLHOGRUUHIOHFWRU
&RQWUROFRPSDUWPHQWEXUQHUDQGFLUFXODWLRQDLUSDVVDJHZD\VRIWKHKHDWHUPXVWEHNHSWFOHDQ
)UHTXHQWFOHDQLQJPD\EHUHTXLUHGDVQHFHVVDU\
3URWHFWWKHKHDWHUIURPEXPSVWRDYRLGGHOLFDWHSDUWVOLNHWKHJODVVWXEHIURPJHWWLQJGDPDJH
3URWHFWWKHKRWJODVVWXEHIURPUDLQZDWHUVSODVKRUDQ\WKLQJWKDWZLOOFDXVHDVXGGHQFKDQJHLQ
WHPSHUDWXUHZKLFKPD\OHDGWRFUDFNLQJRUVKDWWHULQJ
7KHJDVF\OLQGHUVKRXOGEHWXUQHGRIIZKHQWKHKHDWHULVQRWLQXVH
$YRLGWZLVWLQJWKHIOH[LEOHWXEHVDQGKRVHV
$Q\JXDUGRURWKHUSURWHFWLYHGHYLFHUHPRYHGIRUVHUYLFLQJWKHKHDWHUPXVWEHUHSODFHGEHIRUHRSHUDWLQJWKHKHDWHU
$GXOWVDQGFKLOGUHQVKRXOGVWD\DZD\IURPKLJKWHPSHUDWXUHVXUIDFHVWRDYRLGEXUQV
&+,/'5(16+28/'%(&$5()8//<683(59,6(':+(17+(<$5(,17+($5($2)7+(+($7(5
&/27+,1*2527+(5)/$00$%/(0$7(5,$/66+28/'127%(+81*217+(+($7(5253/$&('21
251($57+(+($7(5
,WHPVVWRUHGXQGHURUQHDUWKHKHDWHUZLOOEHVXEMHFWWRUDGLDQWKHDWDQGFRXOGEHVHULRXVO\GDPDJHG
&+,/'5(1$1'$'8/766+28/'%($/(57('727+(+$=$5'62)+,*+685)$&(7(03(5$785(6
%8516$1'&/27+,1*,*1,7,21
'21273/$&($57,&/(62125$*$,1677+,6$33/,$1&(
'212786(256725()/$00$%/(0$7(5,$/61($57+,6$33/,$1&(
'2127635$<$(5262/6,17+(9,&,1,7<2)7+,6$33/,$1&(:+,/(,7,6,123(5$7,21
7+(*8$5',6),77('727+,6$33/,$1&(725('8&(7+(5,6.2)),5(25,1-85<)520%8516$1'
123$572),76+28/'%(3(50$1(17/<5(029(')253527(&7,212)<281*&+,/'5(1257+(
,1),50$6(&21'$5<*8$5',65(48,5('
'2127,167$//2586(7+,6$33/,$1&(,1'2256
'212702',)<7+,6$33/,$1&(
7KLVSURGXFWFRQWDLQVVPDOOEDWWHULHV6ZDOORZHGVPDOO EDWWHULHVFDQFDXVH&+2&.,1*+$=$5'6HHNLPPHGLDWH
PHGLFDODWWHQWLRQLIEDWWHULHVDUHVZDOORZHGRULQKDOHG .HHSFKLOGUHQDZD\IURPWKHVPDOOEDWWHULHV
7KLVKHDWHUPXVWEHSURWHFWHGIURPUDLQ
'212786($1$'$3725$77+(&</,1'(5&211(&7,21
Caution
Page 1

The heater is primarily for outdoor use only (see diagrammatical representations of outdoor areas). Do
not use it for indoors or in an enclosed area. Always ensure that adequate fresh air ventilation is
provided.
Do not use the heater for heating inside domestic premises.
Do not use the heater in the basements or below ground level.
This appliance shall only be used in an above ground open-air situation with natural ventilation, without
stagnant areas, where gas leakage and products of combustion are rapidly dispersed by wind and
natural convection.
Any enclosure in which the appliance is used shall comply with one of the following:
An enclosure with walls on all sides, but at least one permanent opening at ground level and no
overhead cover.
Within a partial enclosure that includes an over head cover and no more than two walls.
Within a partial enclosure that includes an overhead cover and more than two walls, the following
shall apply:
—At least 25% of the total wall area is completely open, and
—At least 30% of the remaining wall area is open and unrestricted.
—In the case of balconies, at least 20% of the total wall area shall
be and remain open and unrestricted.
This appliance shall be used only in an outdoor area and shall
not be used in a building, garage or any other enclosed area.
Always maintain clearance from combustible materials;
from the top 60 cm, and sides 120cm
Heater must be placed on level firm ground.
Never operate heater in an explosive atmosphere like in areas
where petrol or other flammable liquids or vapors are stored.
CEILING
SIDE
120 cm
(47”)
60 cm
(24”)
Heater Location
Page 2

Both ends open
Open side at least
25% of total wall area
30 percent or more in total
of the remaining wall area
is open and unrestricted
Page 3

 Refer to the Data label for confirmation of the gas type to be used with your appliance.
 Use only the pressure regulator and hose assembly supplied with this appliance.
A dented, rusted or damaged gas cylinder may be hazardous and should be checked by your cylinder
supplier. Never use a gas cylinder with a damaged valve connection.
The gas cylinder must be arranged to provide for vapor withdrawal from the operating cylinder
 Never connect an unregulated gas cylinder to the heater.
This appliance is NOT suitable for use with a fixed gas supply system. Use ONLY a 9kg gas cylinder.
 Gas connections on the heater are leak tested at the factory prior to shipment. A complete gas tightness
check must be performed at the installation site due to possible mishandling in shipment or excessive
pressure being applied to the heater.
 Make a soap solution of one part liquid detergent and one part water.
The soap solution can be applied with a spray bottle, brush or rag. Soap bubbles will appear in case of a
leak.
The heater must be checked with a full cylinder.
 Make sure the safety control valve is in the OFF position.
Turn the gas supply ON.
 In case of a leak, turn off the gas supply. Tighten any leaking fittings, then turn the gas supply on and re-
check.
 Never leak test while smoking.
Open side at least
25% of total wall area
30 percent or more in total
of the remaining wall area
is open and unrestricted
Page 4
Gas Requirements
Leakage Test

lgniter
maximum
Warning: check that the glass is not broken before operation.
Igniter
Off: the heater stop work
Hi: maximum temperature position
Lo: minimum temperature position
in
After approximately 10 seconds,
release the control knob.
Variable control knob
5. There is no limitation on the storage of appliances indoors provided that the cylinder is removed
from the appliance; and
6. Storage of an appliance indoors with the cylinder attached is only permitted if the size of the
cylinder complies with AS/NZS 1596; otherwise cylinders must be stored outdoors in a
well-ventilated area and out of reach of children.
2. Disconnect the regulator from the gas cylinder valve.
4. Never store gas cylinders underground or in places without adequate air ventilation.
Operation and Storage
Page 5

Wipe off powder coated surfaces with soft, moist rag. Do not clean heater with cleaners that
are combustible or corrosive.
Remove debris from the burner to keep it clean and safe for use.
If carbon deposits and glass tube goes black, remove the safety guard and clean it with soapy water.
Instructions for cleaning the glass, should it require cleaning on the inside. It is strongly recommended
that you contact the Plumber/gas fitter when the inside of the glass tube requires cleaning. The cleaning
instructions below are for handy persons only. This is a two person job and should take about 10 minutes.
-Loose and remove one side two pieces safety guards.
-Carefully uninstall the glass tube by lifting up and sliding it out from the middle plate cover.
-Dismantle and save the silicone ring which hold the glass in place, spray or pour a little dishwasher
and a spray of window cleaner into glass, wrap a tea towel or soft cloth around the handle end of a
broomstick or pole.
-Move through glass carefully, spray or pour cold/warm water through the glass tube.
-Dry outside of tube with cloth or roll towel and allow 2 min for inside to dry.
-Attach the silicone ring to the bottom end of glass completely, install the glass and safety guards as per
assembly step 5 & 8.
1932 mm
900 mm
650 mm
730 mm
Reflector
Glass Tube
Protective Guard
Upper Leg Support
Front Panel
Side Panel
Lower Leg Support
Bottom plate
Cleaning and Care
Page 6
Parts and Specifications

A. Construction and characteristics
Heater with dancing flame enclosed in transparent glass tube
Heat emission from the reflector
Heat diffuser provides more warmth.
Tilt switch shuts off heater automatically when appliance is accidentallyknockeddown
B.Specifications
For outdoor use only
Gas type – Propane Gas
Test Point Pressure: 2.75Kpa
Pilot injector: 0.20 mm
Burner Injector: 1.75 mm
Gas Consumption: 37.4 MJ/h
Weight: 23.5 kgs
Height: 1932 mm
Page 7

Tools needed:
Philips screwdriver w/ medium blade
Spray bottle of soap solution for leakage test
Parts List:
NOITPIRCSEDTRAPYTITNAUQ
1
Damper
Top plate
1
L
M
N
Gas Hose & Regulator
Control Box Assy
Lower Leg Support
Cylinder Securing Strap Bracket
4
1
1
Bottom Plate
NOITPIRCSEDTRAPYTITNAUQ
A Reflector 1
B 1
1
C
Glass Tube
D
Upper Leg Support
E
Protective Guard
1
4
4
F
G
H
Black Silicone Ring
I
Side Panel
J
Front Panel
K
1
3
1
Reflector
Damper
Glass Tube
Protective Guard
A
B
D
F
Top plate
C
Upper Leg Support
Black Silicone Ring
E
Side Panel
G
H
Front Panel
I
Gas Hose & Regulator
J
Cylinder Securing
Strap Bracket M
Lower Leg Support L
Control Box Assy K
Bottom Plate N
Assembly Parts
Page 8

HARDWARE CONTENTS
AA BB
Wing nut
Qty. 3 Flat
washer ĭ8
Qty. 6
DD EE
3/16” Screw
Qty. 42
CC
Reflector spacer
Qty. 3
Philips
screwdriver
Qty. 1
FF GG
Fixing Bracket
Qty. 4
HH II
Screw
M5 X 12
Qty. 6
Knob
Qty. 1
Stud
Qty. 3
Assembly Parts
Page 9

Hardware Used
1
1. Insert the locator pins of the base into the
holes on the lower leg support and press to
secure. Using 4 pcs screw M5x12 to secure
the lower leg support and base.
Insert the locator pins on the control box
assembly to the holes on the lower leg
support and press to secure. Using 4 pcs
3/16” screw to secure the upper leg support
and control box assembly.
NOTE: Ensure the controls are facing
the same side where there are 2 small slots
in the base - these are for the front panel.
K
L
EE
GG
x 4
Philips
screwdriver x 1
Screw M5 X 12
DD x 4
3/16” Screw Slot
Hardware Used
GG
2
2. Assemble the cylinder securing strap
bracket.
Fix the cylinder securing strap bracket to the
2 pcs lower leg support opposite the front
door, using 2 pcs screw M5x12.
x 1
Philips
screwdriver
M
EE x 2
Screw M5 X 12
Page 10
Assembly Steps

Hardware Used
3
3. Assemble the upper leg support.
Insert the 4pcs upper leg support to the
lower leg support. Secure them with 8 pcs
screw 3/16”.
E
DD
GG
x 8
x 1
Philips
screwdriver
3/16” Screw
4
4. Assemble the top plate to the upper leg
support.
Secure the top plate to upper leg support
using 8pcs screw 3/16".
C
E
Hardware Used
GG Philips
screwdriver x 1
DD x 8
3/16” Screw
Page 11

5
5. Carefully install the glass tube by lifting up
and inserting through the center hole in the
upper plate. Ensure the black silicone ring is
attached to the lower edge of the glass tube
as illustrated. Slide the glass tube through the
hole of the lower plate cover and onto the
middle plate. Check and ensure that the glass
tube is positioned properly and is completely
covering the center hole of the middle plate.
To aid in installation
place black silicone
ring on the middle
plate and then
install glass tube.
Ensure the rim of
the glass tube sits
firmly in the black
silicone ring.
WARNING! The black
silicone ring must be in place
prior to operating the heater. BLACK SILICONE
RING
6
Hardware Used
II x 3
Stud
C
Glass tube fixer
6.Assemble the glass tube fixer onto top plate.
Assemble the glass tube fixer onto top plate
using 3pcs stud.
Please note!
This step will secure the glass tube properly
at the same time.
Page 12

Hardware Used
7
7.1 Put the damper plate onto 3pcs stud then
use the 3pcs reflector spacers to secure it.
7.2 Put the 3pcs Ø8 washer on the top of 3pcs
spacer and put reflector onto spacers, and
secure them with 3pcs Ø8 washer and 3pcs
M8 wing nut.
AA
BB
CC
x 3
x 3
x 6
AA
BB
Wing nut
Washer ĭ8
CC Reflector spacer
Hardware Used
8
8. Assembly the protective guard.
Hang the hooks of the protective guard onto
the holes in supports.
Secure the protective guards with fixing
brackets with 4pcs 3/16" screws.
DD
GG
x 4
Philips
screwdriver
3/16” Screw
x 1
FF Fixing
Bracket x 4
F
Page 13

9
9. Attach the three side panels to the heater
using 18pcs screw 3/16”.
Note : Do not cover the front side where
the control knob is.
Hardware Used
DD
GG
x 18
Philips
screwdriver
3/16” Screw
x 1
10
10.Install the knob to M4x6 screw. Hang the
chain from the inside front panel to the hole on
the control box assembly.
Hardware Used
x 1
HH Knob
HH
I
Page 14

11
WARNING! Ensure the hose does not
contact any high temperature surfaces,
or it may melt and leak causing a fire.
11. Hose connection (Propane Only)
After the cylinder is placed inside the heater,
secure the cylinder with the strap then connect
the regulator to the gas cylinder. Ensure this
connection is done correctly.
Igniter Bu on
Ba ery
12
12 . Install the battery.
The ignitor is powered by a small battery,
if the pilot can't be lighted, the problem may
be the on the battery which is exhausted.
If the battery in igniter is exhausted.
Unscrew the igniter button,then install the
battery and tighten igniter button.
replace the battery(DC1.5V).
Please
Page 15

WARNING!
of the gas system is replaced.
WARNING!
-
erty, serious bodily injury, or death.
:
-
manifolds and valves.
-
If the leak cannot be stopped,
13. Leak Check.
Regulator / Cylinder
connec on
Hose / Regulator
connec on
13
Page 16