Mitsubishi Electric PLK-G-CU-20 User manual

INDUSTRIAL SEWING MACHINE
MODEL
PLK-G-CU-20
TECHNICAL MANUAL
Operation Panel
A180E606P09

Contents
[1] For safe use ____________________________________________ [1]-1
[2] Precautions for use ______________________________________ [2]-1
[3] Explanations of basic screen, icons and operation ____________ [3]-1
1.Screen configuration......................................................................................... [3]-1
2.Explanations of Standard screen 1................................................................... [3]-2
3.Explanations of Standard screen 2................................................................... [3]-3
4.The Up Counter screen is explained below ...................................................... [3]-3
5.The Bobbin Winding screen is explained below................................................ [3]-4
6.Explanations of basic icons............................................................................... [3]-4
7.Explanation of operations.................................................................................. [3]-5
8.Adjusting the Liquid Crystal Contrast................................................................ [3]-6
[4] Sewing Data Compatibility ________________________________ [4]-1
[5] Reading, writing and erasing data __________________________ [5]-1
1.USB................................................................................................................... [5]-1
2.Reading............................................................................................................. [5]-2
3.Writing............................................................................................................... [5]-5
4.Erasing.............................................................................................................. [5]-6
5.Reading data with shortcut icons (Reading from internal memory) .................. [5]-7
[6] Creating stitching data ___________________________________ [6]-1
1.Flow of data creation......................................................................................... [6]-1
2.Description of arrow input screen...................................................................... [6]-4
3.Description of menu.......................................................................................... [6]-5
4.Skip jogging....................................................................................................... [6]-6
[7] Methods of creating sewing data ___________________________ [7]-1
1.Linear input ....................................................................................................... [7]-1
2.Arc input............................................................................................................ [7]-4
3.Circle input........................................................................................................ [7]-8
4.Curve input........................................................................................................ [7]-11
5.Broken line input ............................................................................................... [7]-15
6.Point input......................................................................................................... [7]-18
7.Code data input................................................................................................. [7]-20
8.Back tacking (start/end back tacking) ............................................................... [7]-25
9.Back tacking (overlap back tacking).................................................................. [7]-27
10.Multiple stitching.............................................................................................. [7]-29
11.Offset stitching (with overlap back tacking)..................................................... [7]-32
12.Zigzag stitching (with overlap back tacking).................................................... [7]-34
[8] Controlling the Presser Foot_______________________________ [8]-1
[9] Table of stitching type combinations________________________ [9]-1
[10] Call-up function ________________________________________ [10]-1
- 1 -

[11] Modification mode ______________________________________ [11]-1
1.Main modification mode functions..................................................................... [11]-1
2.Entering the modification mode......................................................................... [11]-1
3.Quitting the modification mode.......................................................................... [11]-2
4.Changing the feed data to home position ......................................................... [11]-2
5.Confirming on the image screen....................................................................... [11]-3
6.Modifying the stitching start position................................................................. [11]-5
7.Deleting a stitch (Deleting the designated No. of stitches)................................ [11]-7
8.Deleting a stitch (Deleting all stitches after the designated position)................ [11]-9
9.Adding a stitch (Adding one stitch).................................................................... [11]-11
10.Adding a stitch (Adding the same stitch)......................................................... [11]-13
11.Modifying the stitch position (Position of subsequent data fixed).................... [11]-15
12.Modifying the stitch position (Subsequent data position moved).................... [11]-17
13.Moving a block (Changing the prior/subsequent data).................................... [11]-19
14.Moving a block (Adding new data to the prior/subsequent data).................... [11]-21
15.Modifying a block 1 (Linear input)................................................................... [11]-23
16.Modifying a block 2 (Broken line, arc, curve input) ......................................... [11]-26
17.Modifying a block 3 (Zigzag input) .................................................................. [11]-32
18.Modifying a block 4 (Changing the feed data)................................................. [11]-34
19.Modifying stitch length (Designated distance modification) ............................ [11]-39
20.Modifying stitch length (All After designated stitch)......................................... [11]-41
21.Modifying material step................................................................................... [11]-43
22.Modifying the stitching speed (All sections after designated position)............ [11]-46
23.Modifying the stitching speed (N stitches after designated position) .............. [11]-48
24.Modifying code data (Adding code data)......................................................... [11]-50
25.Modifying code data (Deleting code data)....................................................... [11]-52
[12] Data conversion mode___________________________________ [12]-1
1.Main data conversion mode functions............................................................... [12]-1
2.Entering the conversion mode .......................................................................... [12]-1
3.Quitting the conversion mode ........................................................................... [12]-2
4.Confirming on the image screen (for the conversion mode)............................. [12]-2
5.Back tacking(Start/end back tacking)................................................................ [12]-3
6.Back tacking(Overlap back tacking).................................................................. [12]-5
7.Zigzag stitching................................................................................................. [12]-7
8.Scaling .............................................................................................................. [12]-9
9.Symmetrical ...................................................................................................... [12]-12
10.Rotation........................................................................................................... [12]-13
11.Multiple............................................................................................................ [12]-15
12.Offset............................................................................................................... [12]-18
[13] Function mode _________________________________________ [13]-1
1.Outline............................................................................................................... [13]-1
2.Explanation of each function mode................................................................... [13]-2
[14] Input/Output setting mode _______________________________ [14]-1
1.Outline............................................................................................................... [14]-1
2.Explanation of input/output setting mode.......................................................... [14]-2
3.Input signal setting table ................................................................................... [14]-6
4.Output signal setting table................................................................................. [14]-9
[15] Program mode _________________________________________ [15]-1
1.Setting methods................................................................................................ [15]-1
2."System, setting file write" and "Setting file read"............................................. [15]-4
- 2 -

[16] Program mode list ______________________________________ [16]-1
1.Wiper................................................................................................................. [16]-1
2.Slow start .......................................................................................................... [16]-1
3.Clamp................................................................................................................ [16]-1
4.Area limit........................................................................................................... [16]-4
5.Needle position ................................................................................................. [16]-5
6.Thread breaking sensor.................................................................................... [16]-5
7.Home position................................................................................................... [16]-5
8.Halt.................................................................................................................... [16]-7
9.Counter ............................................................................................................. [16]-7
10.Brake............................................................................................................... [16]-9
11.Presser foot..................................................................................................... [16]-9
12.Bobbin winding................................................................................................ [16]-10
13.Feed method................................................................................................... [16]-10
14.Speed.............................................................................................................. [16]-11
15.Thread trimming/Thread release..................................................................... [16]-12
16.Step................................................................................................................. [16]-13
17.Jog .................................................................................................................. [16]-13
18.Feed angle...................................................................................................... [16]-14
19.Other............................................................................................................... [16]-15
20.Pattern............................................................................................................. [16]-16
[17] Error display __________________________________________ [17]-1
- 3 -
Thank you for purchasing the Mitsubishi industrial sewing machine PLK-G Series.
Please read this technical manual before starting to ensure correct and long-term
use.
* The contents of this manual may not be reproduced in part or whole.
* The contents of this manual are subject to change without notice.
* An utmost effort has been made to cover all points of operation in this manual.
Contact Mitsubishi if you have any questions regarding the contents.
COPYRIGHT(C)2011 MITSUBISHI ELECTRIC CORPORATION

[1] - 1
[1] For safe use
■For safe use
Always observe the following matters to safely use the Mitsubishi industrial electronic sewing machine PLK-G
Series.
Before starting
Before using this control unit, read all of the technical manuals carefully, and correctly use the unit
following the manual. Also read the "Mitsubishi Industrial Sewing Machine Technical Manual <Sewing
Machine Head>" for details on the general configuration and sewing machine head.
Application and purpose
This control unit is designed to drive and control the Mitsubishi industrial electronic sewing machine
PLK-G Series. Do not use this control unit for other applications or purposes. Do not use this control unit
until it has been confirmed that safety measures have been accurately taken for the installed electronic
sewing machine head section.
Working environment
Please use this control unit in the industrial setting only. And do not use this control unit in the following
type of environment.
(1) Power voltage
* Where the voltage fluctuation exceeds ±10% of the rated voltage.
* Where the specified power capacity (refer to technical manual [Control unit] page [4]-2 “5. Power
capacity”) cannot be ensured.
(2) Magnetic noise
* Where strong fields or magnetic fields are generated, such as near a high-output high frequency
oscillating machine or high frequency welder.
(3) Temperature and humidity
* Where the ambient temperature is 35°C or more and 5°C or less.
* Where the unit will be subject to direct sunlight, or outdoors.
* Near sources of heat, such as heating appliances.
* Where the relative humidity is 45% or less, or 85% or more, and where dew may condense.
(4) Atmosphere
* In an atmosphere containing dust or corrosive gases, etc.
* In a flammable gas or explosive environment.
(5) Vibration
* If excessive vibration could occur when installed on the sewing machine, separately install the
control box.
■Installation
Control box
Correctly install the control box according to this manual.
Accessories
Always disconnect the control unit from the main power supply before installing the accessories listed in
this manual. (Turn the power switch OFF, and disconnect the plug from the socket (power supply line).)
Cable
(1) Lay the connection cables so that excessive force will not be applied during operation. Do not
excessively bend the cables.
(2) Cables laid near operating machine sections must be separated by at least 25mm.
(3) Before connecting the power cable to the control box, confirm that the power voltage matches the
specifications given on the control box's rating nameplate and factory shipment voltage nameplate.
Connect the cable to the indicated positions, and then supply the power. When using a power unit,
connect the cable to the power unit and supply the power. In addition, when using a power unit,
confirm that the power voltage matches the specifications given on the power unit's rating nameplate.
Turn the power switch OFF before making any connections.
Grounding
Always ground the power cord's grounding wire.
Enclosed units and accessories
Connect the electrical enclosed units and accessories only to the positions indicated in the manual.

[1] - 2
Removal
(1) Always turn the power switch OFF and disconnect the plug from the socket (power supply line) before
removing the control box.
(2) Do not pull out the cord when disconnecting the plug. Always hold the plug receptacle when
disconnecting the plug.
(3) Note that a high voltage is applied inside the control panel, so always turn the power OFF and wait
at least ten minutes before opening the control box cover.
■NOTICE CONCERNING MARKING
(1) Electronic sewing machine PLK-G series are applied to CE conformity marking by installing the
exclusive device [PLK-G-CE].
When the products are used in the EU region, these devices are necessary to be installed.
(2) Electronic sewing machine should be use limited to the industrial areas even though above-mentioned
countermeasure is done.
[Warning] Use in residential areas may cause interference.
■Maintenance, inspection and repairs
(1) Follow this manual when carrying out maintenance or inspections related to this control unit.
(2) This unit must be repaired, serviced and inspected only by a worker that has received special training.
(3) Always turn the power OFF before replacing the needle or bobbin, etc., on the head.
(4) Use genuine replacement parts for repairs and maintenance.
■Other safety measures
(1) Keep fingers away from all moving machine parts (especially around the sewing machine needle,
etc.).
(2) Never drop the control unit, or place objects in the clearances.
(3) Do not operate the sewing machine without the protective parts such as the cover, or protection
devices such as the safety breaker.
(4) If any damage is observed in the control unit, if the unit does not operate correctly, or if the operation
is suspicious, always suspend operation. Only operate the machine after the supervisor has adjusted,
repaired or inspected the machine.
(5) The user must not make improvements or changes without instruction from Mitsubishi.
■Caution displays and danger displays
(1)In this manual, the dangers and danger levels that arise with incorrect handling are classified using the
following displays.
Warning The warning display shows that incorrect handling can lead to
death or serious injuries.
Caution The caution display shows that incorrect handling can lead to
injuries or damages to your house, household goods, and
others.
(2)The meanings of these symbols are as follows.
This symbol indicates that the
instructions must be followed.
This symbol indicates an
electrical hazard or caution
(electric shock caution).
This symbol indicates hot
temperature requiring caution.
This symbol indicates that
ground wire connection is
required.
This symbol indicates a
prohibited action.
* Always deliver this manual to the end user.
* Store this manual nearby where it can be referred to when necessary.

[2] - 1
[2] Precautions for use
Warning
1. Do not place foot on the foot switch when turning the power ON.
2. Always turn the power OFF when leaving the sewing machine.
3. Do not inspect the control circuit with a tester.
The tester voltage could be applied on the semiconductor
parts, and cause damage.
4. Always turn the power switch OFF before tilting the sewing
machine head, replacing the needle, or passing thread through the
needle.
5. Always ground the grounding wire.
Always ground the provided grounding wire
(green(green/yellow)).
6. Do not use excessive wiring.
7. A high voltage is applied inside creating a hazardous state, so
always turn the power OFF and wait ten minutes before opening
the cover.
High voltage risk
8. Radiation fins and other parts may be hot. Do not touch the parts.
Control circuit
Green
(Green/yellow)
Power supply

[2] - 2
9. The sewing machine will coast to a stop when the power is turned OFF or a power failure occurs during sewing machine operation.
10. Always align the connector shape and direction, and securely insert the connector.
11. If the position detector's connector dislocates, or the sewing machine is completely locked, the motor will be turned OFF automatically for a
set time to prevent burning. (Note that the motor may not turn OFF if there is incomplete locking or an overload.) When the fault has been
recovered, turn the power OFF and ON once to resume normal operation. The same type of operation will take place if a detector fault or
disconnection occurs.
12．Use the machine away from strong noise sources such as high
frequency welders.
13. When connecting the external switch to an optional connector,
etc., keep the signal wire as short as possible. A long wire could
cause malfunctions.
Use a shielded wire for the signal wire when possible.
14. If the fuse blows, remove the cause, and replace the blown fuse with one having the same capacity.
(View from the front with cover removed) (View from the front
with the cover and CPU removed)
Solenoid board located
on back of machine head
15．Attention when power supply is turned on again
Please make sure that turning on the power supply switch,
after the LED of the front panel on the controlbox is completely turned off.
(Please do not turn on the power supply again while displaying
the screen of the oepration panel.)
* Please note that if power supply is turned on again while LED still turns on,
clamp outputs (O4, O5 port) may go down.
Noise
PLK-G2-PMD
XC-G2-2B-PLK
PLK-G2-CPU
PLK-G2-PMD
PLK-G2-PMM
8
A
fuse
(
one fuse
)
2.5
A
fuse
(
two fuses
)
20
A
fuse
(
two fuses
)
20
A
fuse
(
two fuses
)
15
A
fuse
(
one fuse
)
XC-G2-2B-PLK

[3] - 1
[3] Explanations of basic screen, icons and operation
Note When power supply is turned on, if there is not sewing pattern data in the internal memory, the
message of [PATTERN DATA DOES NOT EXIST] is displayed. Press , then the standard screen
is displayed.
Note When you adjust the contrast to make the operation panel screen easier to view, refer to Chapter 8,
“Adjusting the Liquid Crystal Contrast.”(Page[3]-6)
1. Screen configuration
(1)Sample screen 1 (Standard screen 1)
(2)Sample screen 2 (While menu icon on Standard screen 1 is held down)
(3)Sample screen 3 (When menu is opened on Standard screen 1)
[Line at top of screen]
Normal: Index
(simple explanation of screen)
When any icon is pressed:
The explanation for that icon will
appear. (Refer to sample screen 2.)
Most icons will execute the operation
when the finger is released.
Some icons will continue execution while
the icon is held down.
A
n explanation of the icon and
the screen will appear.
This icon (menu icon) is
pressed, so the icon will
be highlighted.
Input/output setting
mode
Program mode
Reading data
Writing data
Function mode
Data conversion
mode
Modification mode
Methods of creating
stitching data

[3] - 2
2. Explanations of Standard screen 1
The Standard screen 1 is explained in detail below.
… Home position return will be executed.
… The menu window will open
… The Image screen will open.
… The screen of setting for material thickness will open.
The stitching data type for the current work holder position is displayed.
(FEED, SEW, TRIM, etc.)
The current number of stitches is displayed.
The total number of stitches (including the feed data, thread cutting code, end code, and code
data) will be displayed.
The total number of actual stitches (excluding the feed data, thread cutting code, end code, and
code data) will be displayed.
The operation is confirmed (Jogging in forward/reverse direction)
(1) If the work holder is lowered after home position return and the forward jogging direction (upward arrow)
is pressed, the XY table (work holder) will move according to the stitching data. When the icon is
released, the operation will stop at that position. When the jog minus direction (downward arrow) is
pressed, the XY table (work holder) will move in the direction that the stitching data returns. When the
icon is released, the operation will stop at that position.
(2) Check pattern data is correct by jogging buttons, before press start pedal.
(3) During operation, the presser bar lifting will lower at stitching sections in the stitching data, and will rise
at the feed data sections.
(*1) Presser bar lifting : Lowering the presser bar lifting when threading the needle is handy.
Caution Turn the power OFF before threading the needle.
The pattern name is displayed. (Max : eight characters)
The pattern No. is displayed.
The sewing machine stitching speed is increased.
The current stitching speed setting value is
displayed. (0~9)
The sewing machine stitching speed is decreased.
The presser foot is moved up/down. (*1)
(The direction of the arrow (up/down) will change
according to the current state.)
Standard screen 2 opens.
The stitching data is changed.
(Data in internal memory)

[3] - 3
3. Explanations of Standard screen 2
Displays the Standard screen 2 from the Standard screen 1, by pressing .
The Standard screen 2 is explained in detail below.
... Bobbin winding mode (The presser bar lifting will lower, and the Bobbin Winding Setting screen will
open.) (The details are explained on the next page.)
... Moves the needle up/down.
4. The Up Counter screen is explained below
(The Down Counter screen is the same, except for the valid/invalid icon design.)
* The methods of counting with the up counter (down counter) and clearing the counter are determined by the program
mode setting. (Page[16]-7)
●When this screen is displayed, sewing cannot be performed.
The Up Counter screen is displayed.
The Down Counter screen is displayed.
The counter value is displayed.
(Current value/setting value)
Returns to Standard screen 1.
Same as Standard screen 1.
Changes the setting value
or current value.
Changes the validity of
the up counter.
Clears the current value.
(Press to clear the
setting value.)
Returns to the previous
screen.
Displays the setting value
and current value.
Use to change the setting
value and current value.
Determines the
settings.(Returns to
Standard screen 2.)
A set value or the selected value is cleared.

[3] - 4
5. The Bobbin Winding screen is explained below
This screen is used to wind thread on the bobbin. (The presser bar lifting will lower when the bobbin winding
icon is pressed on the Standard screen 2.)
When the work holder switch is turned ON and the start switch is turned ON, the sewing machine will start
rotating at the set speed. The XY table will not move at this time. The sewing machine will stop at the needle
UP position when the start switch is turned OFF.
* The bobbin winding operation is determined by the program mode setting. (Page[16]-10)
6. Explanations of basic icons
The basic icons used commonly on several screens are explained in this section.
… Executes home position return.
… Enter : determines the settings, etc.
… Returns to the previous screen.
… Exits the current mode.
… Cancel : undo the previous operation.
… Opens the menu window.
… Displays the previous/next list when lists are displayed (pattern data list, mode list, etc.)
… Turns skip jogging ON/OFF, and opens the operation setting screens.
Exits the bobbin
winding mode.
*When exit winding mod, presser foot is raised.
Displays the current
setting value.

[3] - 5
7. Explanation of operations
(1)Stitching operations
[1] Reconfirm the stitching data before starting. Take special care to the set stitching speed.
[2] The stitching speed is determined according to the set speed and stitch length. The maximum stitching speed is
determined by the speed setting, and the stitch length limits the stitching speed.
[Caution] Do not change the sewing machine stitching speed during operation except in emergencies.
(Changing the speed can cause fault such as thread catching faults.)
[3] Set the material to be stitched, and turn the work holder switch ON. Next, when the start switch is turned ON, the
sewing machine will start rotating and stitching. Once started, stitching will continue even the operator's foot is
released from the start switch. When the stitching is completed, and the work holder returns to the home position,
the sewing machine will stop and the work holder will automatically rise.
(2)Halting
To stop during the stitching, press the HALT switch (installed on sewing machine head; refer to following drawing).
The sewing machine will stop at the needle UP position. (Standard default setting.)
To cancel the halted state, press the HALT switch again. The following operations will be possible when the halted
state is canceled.
[1] Restart of stitching by pressing start switch. (gray pedal)
[2] Movement to stitching start position with forward jog/reverse jog icons.
[3] Lifting of work holder by pressing work holder switch. (black pedal)
[4] Change of stitching speed by setting stitching speed.
[5] Lifting/lowering of presser bar lifting.
[Note] The needle position during the halted state can be set with the program mode .
[Sewing machine head]
HALT switch
Take down the work holder
Start stitching

[3] - 6
(3)Restitching methods
Restitching can be carried out using the previously explained halt function.
If the operation is halted due to needle thread breakage, etc., set the needle at the UP position, and then using the
forward jog/reverse jog icons, move to the position where the thread broke. Tie the needle thread, etc., and restart
stitching by pressing the start switch.
Caution If the needle must be thread while the power is ON, do not turn
on the start switch while threading. Doing so initiates machine rotation, resulting in an
extremely dangerous situation. To ensure that the start switch is not turned on during
threading, take measures such as moving the start switch away from your feet.
8.Adjusting the Liquid Crystal Contrast
(1)Entering the function mode
►Press on the standard screen, and open the
menu mode.
►Press
(2)Entering the screen mode
►Press on the function mode menu, and open the
screen mode.
(3)Adjustment of LCD contrast
►Set the liquid crystal contrast value using the up and down
arrow icons.
►After setting the value, press the [Enter] icon to
apply the value.
►Back to Standard screen, then contrast setting is completed.

[4] - 1
[4] Sewing Data Compatibility
1.Number and type of Sewing Data
Number Type Explanation
800 ~ 999 G data This is data created with the PLK-G series.
(The maximum number of stitches is 20,000 stitches.)
100 ~ 299 A data This is data created with the PLK-A series
(old model).
400 ~ 499 BA data This is data created with the PLK-B series and E series
(old model). (For embroidery data)
B data This is data created with the PLK-B series and E series
(old model).
600 ~ 799 ( G data )
You can use these data number as preliminary data
number that created with the PLK-G series.
(For example, If the number from 800 to 999 are full, use
these data number.)
2.Sewing Data Compatibility
The following table shows the handling capabilities of the sewing machine (PLK-G series) with respect to
four types of sewing data.
Type Reading Stitching
Continuous input,
Modification and
Conversion Writing
A data Available
(*1) Available Available Available (*3)
BA data Available
(*1) Available Available Available (*3)
B data Available
(*2) Available Available Available (*3)
G data Available Available Available Available
(*1) : When the sewing data is read by copy mode, number of sewing data is added to original sewing data
name.
(e.g. ”PLKG_PAT.100”→”PLKG_100
、、、
.800
、、、
”)
When the sewing data is read by reading function, name and number of sewing data can be edited.
(*2) : When the sewing data is read by copy mode, number of sewing data is not changed.
(e.g. ”PLKG_PAT.600”→”PLKG_PAT.600”)
When the sewing data is read by reading function, name and number of sewing data can be edited.
(*3) : The sewing data can be written after converting to G data.

[5] - 1
[5] Reading, writing and erasing data
1. USB
To perform actions such as storing (reading/writing) sewing data on a device other than the internal memory
or reinstalling the system, a USB device is used. The device is connected to the USB connector on the front
side of the control box.
When using a USB device, be sure to fully insert the device into the USB connector. (Refer to the figure
below.)
[Caution]
■Connect the USB device during use only. After use, remove and store the device in an appropriate
location. When USB device is not connected, insert protection cap to the USB connector.
(Protection cap must be inserted correctly according to the shape of the USB connector)
■Sewing cannot be performed with the USB device inserted.
■Do not insert the USB device during sewing.
■Be careful that nothing bumps into the inserted USB device.
Conditions of Application
▪USB1.1 or USB2.0 compatible USB memory and USB floppy disk drive (Note, however, formatting cannot
be performed with a floppy disk drive connected to the machine.)
▪Required power supply: USB compatible, 500mA or less
Note The write-protector might not be able to recognized according to the kind of USB device.
Please make sure to release the write-protection before writing data to the USB memory.
Inapplicable Devices ■Never connect the following devices.
(Doing so causes malfunctions.)
▪USB device requiring an external power supply (including Computer devices)
▪USB hard disk drive, keyboard, mouse
▪USB memory with fingerprint authentication function or with security function
▪USB memory with hub function
▪Media reader
▪USB device without data storage function
Front panel
USB memory
straightforward
Certainly

[5] - 2
2.Reading
Operation points
·Select “Read mode” from the menu.
·Select the target (internal memory/USB memory).
·Select the data, and execute reading.
Operation details
(1)Selecting data read
Note Data reading excluding the start position cannot be
executed. Read pattern data after home returning.
►Press on the standard screen, and open the
menu mode.
►Press .
(2)·Select the target (internal memory/USB memory).
►When the screen first opens, the mode to read from the
internal memory is selected.
(The mode display at the upper left of the screen is )
►Press to change to reading from the USB memory.
(The mode can also be changed by pressing )
Note If the USB memory is not inserted into the USB
connector, USB memory icon can not be selected.
►If there is a large amount of data, press to
change the screen.
(3)Selecting and setting the data
►Press the number of the data to be read, and then press
.
Note When you read data from the USB memory and
select a data number that already exists in the
internal memory, a message confirming that you
overwrite the data appears. If you do not overwrite
the data, press the icon. If you overwrite the
data, press the icon.
►The read data will be displayed.
[ Caution ] When the target is the USB memory, do not remove the USB memory during reading.
(Doing so may result in data damage.)

[5] - 3
Note When the pattern data number is already known, it is possible to read by specifying the
number directly by the following operations.
(Following operation is limited to reading from an internal memory. )
Reading [Direct reading mode]
Operation details
(1) Selects pattern data read button
Note Data reading excluding the start position cannot be
executed. Read pattern data after home returning.
►Press , then menu screen is displayed.
►Press .
(2)Selects direct pattern number selection
Note Direct pattern number selection is possible only to the
data stored into the internal memory.
►Press direct pattern number button .
(3) Specifies pattern data number 1
(example．Case of reading number [861]. )
►Press number button [8].
►Then 10 of pattern datas which number start from 8 are
displayed.

[5] - 4
(4) Specifies pattern data number 2
►Next press number button [6].
►Then all pattern data which number starts from 86 is
displayed.
►At this time, desired pattern number [861] is displayed, then
press .
Note It is also available, if inputs 3 digits in the column as
[861] and push button.
(5)Data read complete
►Standard screen with the figure of pattern number [861] is
displayed.