Mitsubishi PD-5010 User manual

MITSUBISHI
THE BIG SCREENCOMPANY"
_er_s Guide

ImportantInformation
Precautions
Please read this manual carefully before using your
Mitsubishi plasma monitor and keep the manual handy
for future reference.
/¢,RISK OF ELECTRIC SHOCK /_
DO NOT OPEN
CAUTION:TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER. NO
USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
This symbol warns the user that uninsulated
voltage within the unit may have sufficient
magnitude to cause electric shock.
Therefore, it is dangerous to make any kind
of contact with any part inside of this unit.
This symbol alerts the user that important
literature concerning the operation and
maintenance of this unit has been included.
Therefore, it should be read carefully in
order to avoid any problems.
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT
EXPOSETHISUNITTORAINOR MOISTURE.ALSO DO
NOT USETHIS UNIT'S POLARIZED PLUG WITH AN
EXTENSIONCORDRECEPTACLEOROTHEROUTLETS,
UNLESS THE PRONGS CAN BE FULLY INSERTED.
REFRAINFROMOPENINGTHECABINETASTHEREARE
HIGH-VOLTAGE COMPONENTS INSIDE. REFER
SERVICINGTOQUALIFIEDSERVICEPERSONNEL.
Warning
This equipment has been tested and found to comply with
the limitsfor a Class B digitaldevice,pursuantto Part 15 of
the FCC Rules. These limits are designed to provide
reasonableprotectionagainstharmful interferencewhenthe
equipment is operated in a commercial environment.This
equipmentgenerates,uses,andcanradiateradiofrequency
energyand, ifnot installedand used in accordancewith the
instructionmanual, may causeharmful interferenceto radio
communications.Operationofthis equipmentin a residential
area islikelytocause harmfulinterferencein which casethe
user will be required to correctthe interferenceat his own
expense.
Warnings and Safety Precaution
The Mitsubishi plasma monitor is designed and
manufacturedtoprovidelong,trouble-freeservice.Nomain-
tenance otherthancleaning isrequired.Usea softdry cloth
to clean the panel. Never use
solvents such as alcohol or thinner to clean the panel
surface.
The plasma display panel consists of fine picture
elements (cells).Although Mitsubishi produces the plasma
display panels with more than 99.99 percent active cells,
there may be some cells that do not produce light or re-
mainlit.
Foroperating safety and to avoid damageto the unit, read
carefully and observe the following instructions.
Toavoid shock and fire hazards:
].
2.
3.
4.
5.
6.
7.
Provide adequate space for ventilation to avoid internal
heat build-up. Do not cover rear vents or install the unit
in a closed cabinet or shelves.
The unit is equipped with cooling fans. If you install
the unit in an enclosure, make sure there is adequate
space at the top of the unit to allow hot air to rise and
escape. If lhe monitor becomes too hot, the overheat
protector will be activated and the monitor will be turned
off. If this happens, lurn off the power to the monitor
and unplug the power cord. If the room where the
monitor is installed is particularly hot, move lhe monitor
to a cooler location, and wait for the monitor to cool
for 60 minutes. If the problem persists, contact your
Mitsubishi dealer for service.
Do not use the power cord polarized plug with extension
cords or outlets unless the prongs can be completely
inserted.
Do not expose the unit to water or moisture.
Avoid damage to the power cord, and do not attempt to
modify the power cord.
Unplug the unit during electrical storms or if the unit
will not be used over a long period.
Do not open the cabinet which has potentially
dangerous high voltage components inside. If the unit
is damaged in this way the warranty will be void.
Moreover, there is a serious risk of electric shock.
Do not attempt to service or repair the unit. Mitsubishi
is not liable for any bodily harm or damage caused if
unqualified persons attempt service or open the back
cover. Refer all service to authorized Mitsubishi Service
Centers.

NOTE:
Whenyouconnectacomputertothismonitor,attach
thesuppliedlZerritecores.If youdonotdothis,this
monitorwillnotconformtomandatoryFCCstandards.
Attachingtheferritecores:
Set the ferrite cores on both endsof the
MONITORLINKTM cable (not supplied), and both ends
of the power cable (supplied).
Close the lid tightly until the clamps click.
Use the band to fasten the ferrite core (supplied) to the
MONITORLINK cable.
MONITORLINK cable (not supplied)
band band Connector
core (small) core (small)
Power cable (supplied) core (large)
core (large)
To avoid damage and prolong operating life:
1. Use only with 120V 50/60Hz AC power supply.
Continued operation at line voltages greater than 120
Volts AC will shorten the life of the unit, and might
even cause a fire hazard.
2. Handle the unit carefully when handling and installing
it and do not drop.
3. Set the unit away from heat, excessive dust, and direct
sunlight.
4. Protect the inside of the unit from liquids and small
metal objects. In case of accident, unplug the unit and
have it serviced by an authorized Mitsubishi Service
Center.
5. Do not hit or scratch the panel surface as this causes
flaws on the surface of the screen.
6. For correct installation and mounting it is strongly
recommended to use a trained, authorized Mitsubishi
dealer.
7. Only use tabletop stands or wall-mount brackets that
are designed specifically for this product.
8. As is the case with any phosphor-based display (like a
CRT monitor, for example) light output will gradually
decrease over the life of a Plasma Display Panel.
Recommendations to avoid or minimize uneven phosphor
aging:
Like all phosphor-based display devices and all other gas
plasma displays, plasma monitors can be susceptible to
uneven phosphor aging under certain circumstances.
Certain operating conditions, such as the continuous
display of a static image over a prolonged period of time,
can result in uneven phosphor aging if proper precautions
are not taken. Toprotect your inveslment in this Mitsubishi
plasma monitor, please adhere to the following guidelines
and recommendations for minimizing this type of damage:
* Always enable and use your computer's video game or DVD
player screen saver during use with these sources.
* Display a moving image whenever possible.
* Change the position of the menu display from time m time.
* Always power down file monitor when you are finished using it.
if the plasma monitor is in long term use or continuous
operation, take the following measures to reduce the
likelihood of uneven phosphor aging:
* Lower/he Brighmess and Contrast levels as much as possible
without impairing image readability.
* Display an image with many colors and color gradations (i.e.
photographic or photo-realistic images).
* Create image content wi/h mini_wal contrast between light and
dark areas. Use complementary or pastel colors whenever
possible.
* Avoid displaying images with few colors and distinct, sharply
defined borders between colors.
Contact Mitsubishi at 1-800-332-2110 for other
recommended procedures thal will best suit your particular
application needs.

Contents
Attachment Options for the PD-5OlO Monitor .._ 1
Introduction ......................................................... 2
Introduction to the PD-5OlO
Plasma Monitor ......................................................... 2
The features you'll enjoy include: .............................. 2
Contents of the Package .......................................... 2
Options ..................................................................... 2
Part Names and Function .................................... 3
Front View ................................................................. 3
Rear View /Terminal Board ....................................... 4
Remote Control ......................................................... 5
Battery Installation and Replacement...............................6
Usingthe wiredremote control mode...............................7
Operating Range................................................................7
Handlingthe remote control ..............................................7
Installation ........................................................... 8
Connecting Your PC or Macintosh Computer ............ 9
Connecting Your Document Camera ......................... 9
Connecting Your VCR or Laser Disc Player .............. 9
Connecting Your DVD Player ..................................... 9
External Speaker Connections ................................ 10
Pin Assignments and Signal Levels
for 15 pin RGB (Analog) .......................................... 11
Pin Configuration and Signal
of the MONITORLINK TM Connector ......................... 11
Basic Operations ............................................... 12
POWER .................................................................. 12
Toturn the unit ONand OFF: ..........................................12
VOLUME ................................................................. 12
Toadjustthe volume: .....................................................12
MUTE ..................................................................... 12
Tocancel the sound:......................................................12
INFO ....................................................................... 12
Tocheck the settings:.......................................................12
DIGITAL ZOOM ....................................................... 12
AUTO ADJUST ....................................................... 12
To adjustthe size or quality ofthe picture
automatically:....................................................................12
SLEEP ................................................................... 13
To setthe sleep timer: ....................................................13
Tocheck the remainingtime:...........................................13
Tocancel the off timer......................................................13
WIDE Operations ............................................... 14
Viewing a wide screen (manual) ............................. 14
When watchingvideos or digital video discs ............... 14
When watching high definition video source..................14
Watching computer images ..................................... 15
When"PICTURE SIZE"is setto "OFF",..........................15
PIP SCREEN Operations .................................. 16
Showing a couple of pictures on the screen
at the same time .................................................... 16
Operations in the Side-by-sidemode .............................16
Operations in the Picture-in-picturemode .....................17
Selecting the input signalsto be displayed....................17
Adjusting the On-ScreenMenucontrols.......................17
On-Screen Controls .......................................... 18
Menu Operations .................................................... 18
Video Settings Menu .............................................. 20
Adjusting the picture ......................................................20
Settingthe picture mode accordingto the
brightnessofthe room .....................................................21
Settingthe color temperature ........................................22
Adjusting the color to the desired quality .......................23
Reducingnoise in the picture ..........................................24
Audio Settings Menu ............................................... 25
Adjusting the treble, bass and leftlright balance ...........25
Monitor Settings Menu ............................................ 26
Adjusting the Position,Size, FinePicture,
PictureAdj.......................................................................26
Function Menu ....................................................... 27
Settingthe on-screenmenu ..........................................27
Adjusting the position ofthe menudisplay ....................28
Settingthepowermanagementforcomputerimages.......29
POWERISTANDBYindicator ...........................................30
Settingthe gray level forthe sides of the screen ..........31
Settingthe pictureto suit the movie ...............................31
Setting"MONITORLINK(M-LINK)"..................................32
Reducingunevenagingof the screen............................32
Settingthe time for "INVERSE".......................................33
Settingthe time for "SCREENWIPER"...........................34
Resettingtothe defaultvalues ........................................35
Options Settings Menu ............................................ 36
Settingthe allocation of the audioconnectors............. 36
Settingthe BNCconnectors ..........................................36
Settingacomputer imageto the correctRGB
select screen...................................................................37
Settinghigh definition imagesto the suitable
screen size....................................................................38
Settingthe picture sizefor RGBinput signals ...............38
information Menu ................................................... 39
Checkingthe frequencies, polaritiesof input signals,
andresolution .................................................................39
Settingthe languagefor the menus................................39
Settingthe video signalformat......................................40
External Control ................................................ 41
Table of Signals Supported ............................... 55
Supported resolution.............................................. 5;5
Troubleshooting ............................................... 57
Specifications .................................................... 58
Warranty ............................................................ 60

AttachmentOptionsforthePD-5010Monitor
You can attach your optional mounts or stand to the plasma
monitor in one of the following two ways:
* While it is upright. (See Drawing A)
* As it is laid down with the screen face down (See Drawing
B). Lay the protective sheet, which was wrapped around
the monitor when it was packaged, beneath the screen
surface so as not to scratch the screen face.
• This device cannot be installed on its own.
Be sure to use a stand or wall mount kit.
* See page 2.
•For correct installation and mounting it is
strongly recommended to use a trained,
authorized Mitsubishi dealer.
Failure to follow correct mounting procedures
could result in damage to the equipment or
injury to the installer.
Product warranty does not cover damage
caused by improper installation.
* Use only a matching stand or wall mount kit
designed to fit this product.
Ventilation Requirements for
enclosure mounting
To allow heat to disperse, leave space between
surrounding objects as shown on the diagram at the
right, when installing.

Introduction
Introduction to the PD-5010 Plasma Monitor
Mitsubishi's PD-5010 is a seamless blend of cutting-edge
visual technology and sophisticated design. At 50 inches,
with a 16:9 aspect ratio, the PD-5010 certainly makes a
big impression. However, at a mere 4.68 inches/119 mm
thin, the monitor's sleek techno-art lines blend in well with
your environment. The PD-5010's crisp, vivid image
quality will transform data from any graphic medium from
PCs to DVD players into art. And weighing only 98 lbs/
44.5 kg, it actually can be hung almost anywhere.
Mitsubishi has made sure that a host of multimedia
resources can be easily connected and displayed as
brilliantly as intended on the PD-5010 monitor.
The features you'll enjoy include:
• 50-inch screen
• 16:9 aspect ratio
• Capsulated Color Filter (CCF) aud black matrix
• The enhanced display uses a two-stage filtering system
for deeper, more accurate colors.
• 4.68 inch /119 mm thin
• 98 lbs/44.5 kg light
• High-resolution screen: 1365 x 768 pixels
• 160-degrees of off-axis viewing, horizontally and
vertically.
• Flicker -and warp - free display provides excellent image
geometry even in screen comers
• Not affected by magnetic fields, no color drift or edge
distortion.
• VGA, SVGA, XGA, SXGA, UXGA computer signal
compatibility
• NTSC, PAL, SECAM, composite aud S-Video signal
compatibility
• 480P, 1080I, 720P and HDTV signal compatibility
• PCs, VCRs, Laser Disc and DVD player source
compatibility
• Sophisticated formatting circuitry automatically
converts VGA, SVGA, XGA, SXGA and UXGA signals
to the panel's native resolution
• Precision algorithms are used to convert interlaced
signals to progressive scan.
• User selectable on-screen color temperature settings
• Component video input terminal for DVD, 15.75kHz
(Y, CB, CR )
• Digital broadcasting source compatibility
• Menu-driven on-screen control system that makes image
adjustments a snap
• Seven lauguages (English, German, French, Italian,
Spanish, Swedish, and Japanese)
Contents of the Package
[] Mitsubishi PD-5010 plasma monitor
[] Power cord
[] RGB cable (Mini D-Sub 15-pin to Mini D-Sub 15-pin
connector)
[] Remote control with two AAA Batteries
[] Owner's guide
[] Remote cable
[] Safety metal fittings*
[] Screws for safety metal fitting*
r-'lFerrite core (san,all x 2, large x 2), band
* These fittings are for fastening the unit to a wall to prevent
tipping when used with an optional tabletop stand. Fasten
the safety fittings to the holes in the back of the monitor
using the mount screws.
Option
• Tabletop stand
2

PartNamesandFunction
Front View
0) MENU
Sets the On-Screen Menu (MENU) mode and displays
the main menu.
(_ VOLUME DOWN and UP
Adjusts the volume. Functions as the CURSOR
(A/V) buttons when the MENU is on the screen.
LEFT/- and RIGHT/+
Enlarges or reduces the image. Also functions as the
CURSOR ('4 /I_) buttons when the Menu is on the
screen.
_) INPUT /EXIT
Switches the input, in the following order.
[ _'iDEO1 _IDEO2 _IDEO3 _VD/HD_
_ONITORLINK RGB/PC2 RGB/PC1
Functions as the EXIT buttons in the On-Screen Menu
(MENU) mode.
(_) POWER/STANDBY indieat or
When the power is on ............................. Lights green.
When the power is in the staudby mode ... Lights red.
_) Power
Turns the monitor's power on and off.
(_ Remote sensor window
Receives the signals from the remote control.
*MONITORLINK is available only after proprietary
tuner/controller has been connected.
3

Rear View/Terminal Board
--B
--D
--F
!
A EXT SPEAKER L and R
Connect speakers here. Maintain the correct polarity.
BVIDEO 1,2,3
Connect a VCR or other video device here. Only one
of these three inputs can be used.
C DVDI /HDI
Connect DVD's, High Definition or Laser Discs, etc.
here.
D RGBI
inputs the analog RGB signal of personal computer,
etc.
ERGB2/DVD2/HD2
RGB2: inputs the analog RGB signal.
DVD2/HD2: Connect DVD's, High Definition or
Laser Discs, etc. here.
FMONITORLINK1M (M-LINK) INPUT
A proprietary input for connecting a Mitsubishi tuner/
controller. Input will appear in menus only after the
proprietary tuner/controller has been connected.
G
H
I
J
K
CONTROL LOCK
When "CONTROL LOCK" is set "ON", the buttons
on the set's control panel do not function.
REMOTE CONTROL
Connect the supplied remote cable here.
MONITORLINK TM CONTROL
This terminal can be used for external control of power
ON/OFF, input selection AUDIO MUTE and other
features. It is also used with a proprietary Mitsubishi
tuner/controller.
AUDIOI /AUDIO2 /AUDIO3
Audio 1: Connect the audio output froln the
device connected to Video 1, 2 or 3.
Audio 2: Connect the audio output frolrl the
device connected to DVDI/HDI.
Audio 3: Connect the audio output frolrl the
device connected to RGB2/DVD2/HD2.
ACIN
Connect the included power cord here.
4

Remote Control
® @
@
@
_D POWER ON/OFF
Switches Power ON/OFF.
(This does not operate when POWER/STANDBY
indicator of the main unit is off.)
O RGB/PC
Press this button to select RGB/PC as the source.
_ _GB/PCl _GB/PC2 _'ONtTO RLINK* _
RGB/PC can also be selected using the INPUT button
on the monitor. The input switches as follows each time
the button is pressed:
L_'_DEO1 _'iDEO2 '¢_ffDEO3 _VD/HD
MONITORLtNK* 4-RGB/PC24-RGB/PCl
DVD /HD
Press this button to select DVD/HD as the source.
DVD/HD can also be selected using the INPUT
SELECT button on the monitor. The input switches as
follows each time the button is pressed:
L_[DEO _lffDEO2 _ffDEO3 _VD/HD
MONITORL*NK*,-RGS/PC2*-RGB/PCl_
VIDEO
Press this button to select VIDEO as the source.
_ _[DEOI _IDEO2 _IDEO3_
VIDEO can also be selected using the INPUT SELECT
button on the monitor. The input switches as follows
each time the button is pressed:
27;;
MENU/ENTER
Press this button to access the on-screen menu.
Press this button during the display of the main menu
to go to the sub menu.
OADJUST(A/V/ _ /))
Use these buttons to select items or settings and to
adjust settings or switch the display patterns.
EXIT
Press this button to exit the OSM controls in the main
menu. Press this button during the display of the sub
menu to return to the main menu.
POIN'I_R
Press this button to display the pointer.
ZOOM (A/V)
Enlarges or reduces the image.
VOLUME (A/V)
Adjusts the volume.
_D MUTE
Mutes the sound.
FORMAT
The type of broadcast is detected automatically, and
the recommended wide screen is set.
5

QINFO
Displays the source settings on the screen.
_) SLEEP
Activates the offtimer for the unit.
PIP
Press this button to select a screen mode from among
single mode, side by side, and picture in picture.
SELECT
Press this button to select the active picture in a multi
screen mode.
_]_ AUTO POSITION
Press this button to adjust Fine Picture, Picture ADJ,
Position, and Contrast automatically, or to switch the
screen size to ZOOM mode automatically with the
superimposed caption displayed fully only when the
picture contains dark areas above aud below the picture.
_) REMOTE CONTROL SIGNAL TRANSMITTER
Transmits the remote control signals.
_) REMOTE JACK
Insert the plug of the supplied remote cable here when
using the supplied remote control in the wired
condition.
Battery Installation and Replacement
Insert the 2 "AAA" batteries, making sure to set them in
with the proper polarity.
I. Press and open the cover.
2. Align the batteries according to the (+) and (-)
indication inside the case.
* input isavailable only after proprietary tuner/controller
has been connected. 3. Replace the cover.
6

Using the wired remote control mode
Connect the supplied remote cable to the remote control's
jack and the "REMOTE CONTROL" terminal on the
monitor.
When the cable is connected, the mode automatically
switches to wired remote control. When the wired remote
control mode is used, the remote control can be operated
even if no batteries are loaded.
Operating Range
* Use the remote control within a distance of about 7 m/
23fl. from the front of the monitor's remote control sensor
madathorizontal and vertical augles of up to approximately
30°.
* The remote control operation may not function if the
monitor's remote control sensor is exposed to direct
sonlight or strong artificial light, or if there is au obstacle
between the sensor aud the remote control.
Handling the remote control
•Do not drop or mishandle the remote control.
• Do not get the remote control wet. If the remote control
gets wet, wipe it dry immediately.
• Avoid heat and humidity.
• Remove the batteries when not using the remote control
for a long period.
• Do not use new and old batteries together, or use
different types together.
• Do not take apart the batteries, heat them, or throw them
into a fire.
• When using the remote control in the wireless condition,
be sure to unplug the remote cable from the REMOTE
CONTROL terminal on the monitor.

Installation
8

Connecting Your PC or Macintosh
Computer
Connecting your PC or Macintosh computer to your
plasma monitor will enable you to display your computer's
screen image for an impressive presentation. The plasma
monitor supports the signals described on page 55.
To connect a PC, Macintosh or compatible graphics
adapter, simply:
1. Turn off the power to your plasma monitor and
computer.
2. If your PC doesnot support SXGA/XGA/SVGA/VGA
you will need to install an SXGA/XGA/SVGA/VGA
graphics board. Consult your computer's owner's
manual for your SXGA/XGA/SVGA/VGA
configuration, tfyou need to install a new board, see
the manual that comes with your new graphics board
for installation instructions.
3. The plasma monitor provides signal compatibility up
to VESA 1600 x 1200 (UXGA). However, it is not
recommended to use this resolution due to image
readability on the monitor's 1365 x 768 native pixel
resolution panel.
4. Use the signal cable that's supplied to connect your PC
or Macintosh computer to the plasma monitor. For
Macintosh, use the monitor adapter to connect to your
computer's video port.
5. Turn on the plasma monitor and the computer.
6. If the plasma monitor goes blank after a period of
inactivity, it may be caused by a screen saver installed
on the computer you've connected to the plasma
monitor.
When using a Macintosh with the plasma monitor, the
following four display standards are supported using the
Macintosh adapter :
13" fixed mode
16" fixed mode
19" fixed mode
21" fixed mode
The 19" fixed mode is recommended for the plasma
monitor.
Connecting Your Document Camera
You can connect your plasma monitor to a document
camera. To do so, simply:
I. Turn off the power to your plasma monitor and
document camera.
2. Use a standard video cable to connect your document
camera to the Video input on your plasma monitor.
3. Turn on the plasma monitor and the document camera.
ConnectingYourVCR or Laser Disc Player
Use common RCA cables (not provided) to connect your
VCR or laser disc player to your plasma monitor. To make
these connections, simply:
I. Turn off the power to your plasma monitor and VCR
or laser disc player.
2. Connect one end of your RCA cable to the video output
connector on the back of your VCR or laser disc player,
connect the other end to the Video input on your plasma
monitor. Use standard RCA audio patch cords to
connect the audio from your VCR or laser disc player
to your plasma monitor (if your VCR or laser disc player
has this capability). Be careful to keep your right and
left channel connections correct for stereo sound.
3. Turn on the plasma monitor and the VCR or laser disc
player.
Connecting Your DVD Player
You can connect your plasma monitor to a DVD player.
To do so, simply:
I. Turn off the power to your plasma monitor and DVD
player.
2. Use a standard video cable to connect your DVD player
to the Y, Cb, and Cr inputs on your plasma monitor.
Or use the DVD-player's S-Video output. Use a
standard S-Video cable to connect to the S-Video input
on the plasma monitor.
3. Turn on the plasma monitor and the DVD player.
9

External Speaker Connections
External speakers (not supplied) may be colmected to the
plasma monitor to reproduce sound from VIDEO, DVD
or RGB signal sources.
External speakers may be COlmected directly to the
SPEAKERS terminals.
To connect external speakers directly to the plasma
monitor:
|.
2.
Strip the ends of the speaker wires.
Press down the tabs below the SPEAKERS terminals,
insert the speaker wire and release the tab to secure the
speaker wire connection:
[a] Connect the right speaker (located at right side
of the monitor when viewed from the front)
positive (+) wire to RIGHT +.
[b] Connect the right speaker negative (-) wire to
RIGHT -.
[c] Colmect the left speaker negative (-) wire to LEFT-.
[d] Connect the left speaker positive (+) wire to LEFT+.
10

Pin Assignments and Signal Levels for 15 pin RGB (Analog)
il
11

BasicOperations
POWER
Toturn the unit ON and OFF:
1. Plug the power cord into an active AC power outlet.
2. Press the POWER ON button (on the remote control)
to turn on the unit.
The monitor's POWER/STANDBY indicator will light
up (green) when the unit is on.
3. Press the POWER OFF button (on the remote control
or the unit) to turn offthe unit.
The monitor's POWER/STANDBY indicator turns red
and the standby mode is set (only when turning off the
unit with the remote control).
VOLUME
Toadjust the volume:
1. Press and hold the VOLUME/x button (on the remote
control or the unit) to increase to the desired level.
2. Press and hold the VOLUME V button (on the remote
control or the unit) to decrease to the desired level.
MUTE
Tocancel the sound:
Press the MUTE button on the remote control to cancel
the sound; press again to restore.
INFO
Tocheck the settings:
1. The screen changes each time the INFO button is
pressed.
2. if the button is not pressed for approximately three
seconds, the menu turns off.
DIGITAL ZOOM
Digital zoom specifies the picture position and enlarges
the picture.
1.Press the POINTER button to display the pointer. ( I_' )
To change the size of the picture:
Press the ZOOM+ button and enlarge the picture.
The pointer will change to resemble amagnifying glass.
A press of the ZOOM- button will reduce the picture
and return it to its original size.
To change the picture position:
Select the position with the AV 4 P" buttons.
2. Press the POINTER button to delete the pointer.
AUTO ADJUST
To adjust the size or quality of the picture
automatically:
Press the AUTO ADJUST button.
Information
•AUTO ADJUST ON setting
When RGB (still picture) input
is selected ......... Fine Picture, Picture ADJ, Position,
and Contrast will be adjusted
automatically.
When RGB (motion picture),
VIDEO, or Y/Pb/Pr (component) input
is selected ......... The screen size switches to ZOOM
mode automatically with the
superimposed caption displayed fully
only when the picture contains dark
areas above and below the picture.
12

SLEEP
To set the off timer:
The off timer can be set to turn the power off after 30, 60,
90 or 120 minutes.
1. Press the SLEEP button to start the timer at 30 minutes.
2. Press the SLEEP button to the desired time.
3. The timer starts when the menu turns oft;
30 -'_60 -">90 -"> 120 -"> 0•
/ /
To cancel the off timer:
1. Press the SLEEP button twice in a row.
2. The offtimer is canceled.
zz:zz:zz:zz:zz:zz:zz:zz:zz:zz:zz:zz:
zz:zz:zz:zz:zz:zz:zz:zz:zz:zz:zz:zz:__
To check the remaining time:
1. Once the offtimer has been set, press the SLEEP button
once.
2. The remaining time is displayed then turns offaffer a
few seconds.
3. When five minutes remain the remaining time appears
until it reaches zero.
13

WIDEOperations
Watching with a wide screen (manual)
With this function, you can select one of four screen sizes.
When watching videos or digital video discs
STRETCHED size screen
1. Press the FORMAT button on the remote control.
2. Within 3 seconds ...
Press the FORMAT button again.
The screen size switches as follows:
ZOOM-_NARROW _STANDARD-_STRETCHED
ZOOM size screen
The picture is expanded in the horizontal and vertical
directions at different ratios.
* Use this for watching normal video programs (4:3) with a
wide screen.
When watching high definition video source
1. Press the FORMAT button on the remote control.
STANDARDsize screen (16 : 9)
The picture is expanded in the horizontal and vertical
direction, maintaining the original proportions.
* Use this for theater size (wide) movies, elc.
NARROW size screen (4:3) The full size screen is displayed.
* The picture has the ,same size as video pictures (16 :9),
The normal size screen is displayed.
* The picture has the same size as video pictures with a
4 :3 aspect ratio.
STANDARDsize screen
The image is expanded in the horizontal direction.
* Images compressed in the horizontal direction ("squeezed
images") are expanded in the horizontal direction and
displayed on the entire screen. (Normal images are
expanded in the horizontal direction.)
14

STANDARDsizescreen
Watching computer images
Switch to the wide screen mode to expand the 4 : 3 image
to fill the entire screen.
1.Press lhe FORMAT button on the remote control.
2.Wilhin 3 seconds ...
Press the FORMAT button again.
The screen size switches as follows:
[-) NARROW -'_ STANDARD
/
NARROWsize screen (4:3 or SXGA 5:4)
The image is expanded in the horizontal and vertical
direction.
WHENWIDE SIGNALS ARE INPUT
TRUE
The picture has the same size as the normal computer
image.
STANDARDsize screen
The image is true resolution.
STANDARD
The image is expanded in the horizontal direction.
WHENWIDE SIGNALS ARE INPUT
STANDARDsize screen
When "PICTURE SIZE" is set to "OFF"
The screen size switches as follows:
[-'>TRUE --> STANDARD,
TRUEsize screen (VGA, SVGA 4:3)
The image fills the screen.
Information
• Supported resolution
See page 55 for details on the display output of the
various VESA signal standards supported by the
monitor.
• "PICTURE SIZE" setting
When the setting of "PICTURE SIZE" is OFF. the
size of RGB-input pictures will be TRUE in place of
NARROW.
•When 852 (848) dot x 480 line wide VGA*
signals with a vertical frequency of 60 Hz and
horizontal frequency of 31.7 (31 .O) kHz are in-
put
Select an appropriate setting for RGB SELECT mode
referring to the"Table of Signals Supported" on page
55.
* " IBM PC/AT" and "VGA" are registered trademarks
of IBM, Inc. of the United States.
The image is true resolution.
15

PIPSCREENOperations
Showing a couple of pictures on the screen
at the same time
* An RGB-input picture may not be displayed in these
modes, depending on the input signal specifications.
1. Press the PIP button to select a screen mode from among
single mode, side by side, and picture in picture.
Side by side
Operations in the Side-by-side mode
To change the picture size, press the cursor4 or )'button.
,bo oo$ , button
ABB
Picture in picture
Main screen
Information
Multi screen operations may not function depending
on the combination of input signals. In the table
below, "0" means Yes, "'X'" means No.
PJclures _lJsplaye_lon me d_marr sc_ee_
WOEO1 WOEO2 WOEO3 _I)/DVDI HI)/DVD2 £GBIPCl £G_/PC2 £G_/PC3
PJclures WOEO1 X X X 0 0
d_spragedo_ WOEO2 X X X 0 0
[_e _e_s_b WOEO3 X
s_ree_ _l)/t3VDI 0
_l)/t3VD2 X
RG8/'2Cl X
RGS/'OCZ 0 0 0 X X X ×
RGS/'2C_ 0 0 0 0 X X ×
• Multi screen operations may not function
depending on the type of the RGB signals.
Ibutton_ _ _ button
A
To swap the picture on the right and the left, press the
cursor A button.
B
• bu_on
B
To make the desired picture active, press the SELECT
button.
B
SELECT button
B
16