Standby Logo Searching Source Display Cooling
Power On <CR>*pow=on#<CR> <CR>*POW=ON#<CR>
Power off <CR>*pow=off#<CR> <CR>*POW=OFF#<CR>
Power Status <CR>*pow=?#<CR> <CR>*POW=ON#<CR>(or *POW=OFF#)
VGA/YPbPr <CR>*sour=RGB#<CR> <CR>*SOUR=RGB#<CR>
Composite <CR>*sour=vid#<CR> <CR>*SOUR=VID#<CR>
SVIDEO <CR>*sour=svid#<CR> <CR>*SOUR=SVID#<CR>
Current source <CR>*sour=?#<CR> <CR>*SOUR=RGB#<CR>(*SOUR=VID# / *SOUR=SVID#)
Contrast + <CR>*con=+#<CR> <CR>*CON=+#<CR>
Contrast - <CR>*con=-#<CR> <CR>*CON=-#<CR>
Contrast value <CR>*con=?#<CR> <CR>*CON=___#<CR> ( ___ is Contrast value.)
Brightness + <CR>*bri=+#<CR> <CR>*BRI=+#<CR> This command is acceptable when picture menu setting is user1 or user2.
Brightness - <CR>*bri=-#<CR> <CR>*BRI=-#<CR> This command is acceptable when picture menu setting is user1 or user2.
Brightness value <CR>*bri=?#<CR> <CR>*BRI=___# <CR> ( ___ is Brightness value)
Aspect 4:3 <CR>*asp=4:3#<CR> <CR>*ASP=4:3#<CR> This command is acceptable when picture menu setting is user1 or user2.
Aspect 16:9 <CR>*asp=16:9#<CR> <CR>*ASP=16:9#<CR> This command is acceptable when picture menu setting is user1 or user2.
Aspect Auto <CR>*asp=AUTO#<CR> <CR>*ASP=AUTO#<CR>
Aspect Real <CR>*asp=REAL#<CR> <CR>*ASP=REAL#<CR>
Lamp 1 Hour <CR>*ltim=?#<CR> <CR>*LTIM=___#<CR> ( ___ is Lamp used hour.) Show the Lamp used time.
Normal mode <CR>*lampm=lnor#<CR> <CR>*LAMPM=LNOR#<CR>
Economic mode <CR>*lampm =eco#<CR> <CR>*LAMPM=ECO#<CR>
LampMode Status <CR>*lampm=?#<CR> <CR>*LAMPM=LNOR#<CR>(*LAMPM=ECO#)
Blank On <CR>*blank=on#<CR> <CR>*BLANK=ON#<CR>
Blank Off <CR>*blank=off#<CR> <CR>*BLANK=OFF#<CR>
Blank Status <CR>*blank=?#<CR> <CR>*BLANK=ON#<CR>(*BLANK=OFF#)
Freeze On <CR>*freeze=on#<CR> <CR>*FREEZE=ON#<CR>
Freeze Off <CR>*freeze=off#<CR> <CR>*FREEZE=OFF#<CR>
Freeze Status <CR>*freeze=?#<CR> <CR>*FREEZE=ON#<CR>(*FREEZE=OFF#)
Menu On <CR>*menu#<CR> <CR>*MENU#<CR>
Up <CR>*up#<CR> <CR>*UP#<CR>
Down <CR>*down#<CR> <CR>*DOWN#<CR>
Right <CR>*right#<CR> <CR>*RIGHT#<CR>
Left <CR>*left#<CR> <CR>*LEFT#<CR>
enter <CR>*enter#<CR> <CR>*ENTER#<CR>
Auto <CR>*auto#<CR> <CR>*AUTO#<CR> Auto signal select and position.
Zoom In <CR>*zoomI#<CR> <CR>*ZOOMI#<CR>
Zoom out <CR>*zoomO#<CR> <CR>*ZOOMO#<CR>
NoteCMD
Power
RS232 Software specification
1.Each input character will be echoed.
2.If the command format is illegal, it will echo “Illegal format＂.
3.If the command format is correct, it will action and return ACK.
4.If the command format is correct, but it is not valid for this model, it will echo “Unsupported item＂.
5.If the command format is correct, but can't be execute in some condition, it will echo “Block item＂.
6.Press Enter right after ">" wouldn't get any echo
7.Press Space after ">" then Enter would echo“Illegal format＂
Notice XD95U can detect the capital letter and the small letter for input character, but ACK is only the capital letter.
ACTION ASCII ACK State(The command is acceptable in green state.)
Miscellaneous
Lamp Control
Picture Setting
Source Selection
