MIXER Vertigo User manual

TROWEL
MIXER VERTIGO
MACHINE
MANUAL OF INSTRUCTIONS
ORIGINAL INSTRUCTIONS
Revision n…… of ……
MIXER TECHNOLOGY srl
Via dei Carabinieri, 45, 36040
Torri di Quartesolo (VI) Italy
www.mixersrl.com

Instruction Manual Mixer Plus Mixer Technology srl pag.2
GENERAL INDEX
CE MARKING .......................................................................................... 3
FINAL TESTING AND COMMISSIONING ...................................................... 3
RESERVED RIGHTS ................................................................................. 3
TECHNICAL DATA.................................................................................... 4
DIMENSIONS OF THE MACHINE ................................................................ 4
PARTS LIST ............................................................................................ 6
USE DENOMINATION ............................................................................... 7
SOURCES OF ENERGY SUPPLY .................................................................. 7
DISPOSAL .............................................................................................. 7
PROCESSING PHASES.............................................................................. 8
ELECTRICAL CONNECTIONS ..................................................................... 8
CONTROL PANEL ..................................................................................... 9
ELECTRONIC COMMAND AND CONTROL PANEL ........................................... 9
TROWEL COMMAND ...............................................................................10
CHECKS BEFORE SWITCHING ON.............................................................10
SWITCHING ON MACHINE .......................................................................11
STOP AND PAUSE OF THE MACHINE .........................................................11
MACHINE SWITCHING OFF ......................................................................11
CLEANING THE MACHINE ........................................................................11
RESET GEARMOTOR PROTECTION INTERVENTION .....................................12
ORIGINAL ACCESSORIES ON REQUEST.....................................................13
WARRANTY ...........................................................................................14

Instruction Manual Mixer Plus Mixer Technology srl pag.3
CE MARKING
FINAL TESTING AND COMMISSIONING
(by the Manufacturer or the authorized Dealer)
The machine is already tested at the Manufacturer's premises.
The commissioning of the machine at the client is carried out by Manufacturer
or the Authorized Dealer.
At the end of the testing, the Manufacturer or Authorized Dealer fills in the
testing and commissioning certificate, which is signed by the testing
technician, the operator in charge (or any other authorized operator), and by
the safety manager, who shall certify the positive result of the same.
RESERVED RIGHTS
The contents on this manual can’t be reproduced and disclosed (totally or
partially) without written authorization of the Manufacturer.

Instruction Manual Mixer Vertigo Mixer Technology srl pag.4
TECHNICAL DATA
The models available of the machine TROWEL MIXER VERTIGO MACHINE
Protection grade of command and control: IP44
Protection grade of trowel: IP20
Hopper capacity: 5 litres
Power cable length: 3 meters
DIMENSIONS OF THE MACHINE

Instruction Manual Mixer Vertigo Mixer Technology srl pag.5
10
11
9
3
1
2
5
4
6
7
8
12
4
6
7
8
13
18
17
16
15
14
22
21
19
20

Instruction Manual Mixer Vertigo Mixer Technology srl pag.6
PARTS LIST
1. Water tank cap
2. Water tube
3. Water tank
4. Disk speed controller
5. Lifting handles
6. Thermal protector (gearmotor)
7. Fuse (3,15 A – water pump)
8. Mains power plug trowel (with a block device plug)
9. Rubber band tank firm
10. General power plug
11. General power cable
12. General switch (ON-OFF breaker with release coil)
13. Spray water pipe connection
14. Nozzle water spray
15. Disk support handle
16. Gearmotor
17. “1 – 0” trowel switch
18. Button spray water
19. Handle
20. Power cord trowel
21. Sponge with velcro
22. Disk with velcro

Instruction Manual Mixer Vertigo Mixer Technology srl pag.7
USE DENOMINATION
The machine has been designed and manufactured for the following destination of
use:
Any other different use must be considered potentially improper.
SOURCES OF ENERGY SUPPLY
DISPOSAL
At the disposal time of the machine, compulsorily observe the provisions of the
regulations in force.
Separate the parts making up the machine according to the different construction
materials (plastic, copper, iron, etc...).
Lubricant liquids and any other fluids shall absolutely not be dispersed in the
environment.
DESTINATION
OF USE
Building sector.
PLACE OF WORK
Building sites, inside or outside sufficiently lighted and
suitable buildings complying with the regulations in force in
the country of use on safety and health on work positions.
The machine has to lean on a surface assuring its stability
with reference to its weight and its overall dimensions.
FORESEEN USE
Mechanical processing: trowelling and/or peeling of plaster
for finishing flat
CHARGED
WITH THE USE
A single authorized operator meeting the professional
requirements described
ENERGY SOURCES
FED EQUIPMENT
ELECTRIC
Command and control panel, water pump, transformer,
gearmotor.
WATER
Hydraulic plant.

Instruction Manual Mixer Vertigo Mixer Technology srl pag.8
PROCESSING PHASES
1)Water load in the tank;
2)Assembly of the sponge on the disk with Velcro;
3)Connection of the trowel power plug to command and control panel ;
4)Connection water tube to command and control panel;
5)Connection to the mains;
6) Switched on machine;
7) Adjustment of the speed of disk;
8) Trowelling or scraping of the surface;
9) If required from the processing spray water;
10) Possible work breaks
11) Switched off machine
12) Cleaning of the trowel
13) Water drainage from the hydraulic system during wintertime
ELECTRICAL CONNECTIONS
The electrical supply network that is connected to the machine must meet the
specifications, then the line cables and switch must be properly sized for passage of
power corresponding to the installed capacity.
Connect the plug to the power source placed on the overall distribution and supply
(provided by the regulator).

Instruction Manual Mixer Vertigo Mixer Technology srl pag.9
CONTROL PANEL
ELECTRONIC COMMAND AND CONTROL PANEL
REF
DENOMINATION
FUNCTION
1 Master switch to two
pos. “ON-OFF”
Pos. "ON": gives to the command and control
panel power;
Pos "OFF": Shuts the command and control
panel power off.
2
Disk speed regulation
(Min-max) "Speed
regulation"
Pos. “0” Machine stopped;
Pos. “1” Minimum rotation speed;
Pos. “2” Medium rotation speed;
Pos. “3” Maximum rotation speed;
3 Fuse
“Fuse (3,15A)”
It contains a fuse of 3,15 A, for the water
pump protection.
4
Thermal protector
(Gearmotor)
“Thermal”
When it is activated, signals the failure to the
trowel motor (for reset, press the button).
5 Trowel power outlet It is connected the trowel power plug.
2
1
3
4
5

Instruction Manual Mixer Vertigo Mixer Technology srl pag.10
TROWEL COMMAND
REF
DENOMINATION
FUNCTION
1 Two pos. Switch
pos. “1 – 0”
Pos. “1”: It starts the trowel gearmotor;
Pos. “O”: It stops the trowel gearmotor
2 Water button
Pushed forward makes the water spraying by
starting the pulse pump.
CHECKS BEFORE SWITCHING ON
1. Make sure that there are not any non authorized persons close to the machine.
2. Make sure that the machine is braked and properly positioned;
3. Make sure that all components are properly installed;
4. Make sure to fill up the water tank;
5. Make sure that the trowel power plug is connect and block to the command and
control panel;
6. Make sure that the spraying water tube is connect to spraying water connection
on the command and control panel;
7. Make sure that the plug of the power supply cable is connected to the outlet of
the main distribution panel and electric power supply and that the main electric
switch is in pos."0";
8. Make sure to have read and understood in all its parts the¨ Instructions for use
and maintenance ¨and the technical data sheets of pre-mixed products to be
used for the processing;
1
2

Instruction Manual Mixer Vertigo Mixer Technology srl pag.11
SWITCHING ON MACHINE
1. Powers up the command and control panel by pushing the main switch "ON –
OFF" on position "ON";
2. Holding the trowel with both hands and set the speed by turning the selector
on the electrical panel;
3. Pushing the "1 – 0" switch located on the trowel in pos."1", the disk will start
spinning at the minimum speed.
4. Approach the surface to work and exert a sufficient pressure on it,
accompanying the trowel with a rotation and translator movement, in
accordance with the usual techniques;
5. If necessary use the water spraying hose to moisten the surface to work by
pushing the water spray button. At empty tank, filling it up with clean water
STOP AND PAUSE OF THE MACHINE
1. Turn off the trowel by pushing the "1 – 0” button located on the trowel
in pos."0" and wait for the disk to stop;
2. Lay the trowel on the ground on a plain surface that insures its stability;
MACHINE SWITCHING OFF
1. Turn off the trowel by pushing the "1 – 0” button located on the trowel in
pos."0" and wait for the disk to stop;
2. Lay the trowel on the ground on a plain surface that insures its stability;
3. Cut off the power to the command-and-control panel by pushing the main
switch in "OFF" position;
4. Disconnect the trowel power plug from the mains;
5. Unblock and disconnect the trowel power plug from the outlet situated on the
command and control panel;
6. Unplug the water spraying tube from the water spaying outlet located on the
command and control panel;
7. Perform a thorough cleaning of the machine;
CLEANING THE MACHINE
1) Clean with a dry cloth;

Instruction Manual Mixer Vertigo Mixer Technology srl pag.12
a) the general electric power cables and trowel and wrap them near the
command and control panel;
b) the trowel;
c) the command and control panel;
d) the disk with Velcro;
2) Remove from the disk the sponge with Velcro and wash it with clean water;
3)When dry, reassemble the sponge with Velcro on the disk.
RESET GEARMOTOR PROTECTION INTERVENTION
The arrest of the trowel gearmotor points the thermal protection intervention, causes
by an overall of electricity and/or short circuit or absence of electricity.
To reset and restart the machine the authorized operator has to behave as follow:
1. Push the "1 – 0 " switch in pos."0";
2. Push the "ON – OFF" switch in "OFF” position;
3. Push the reset button of the Thermoprotection ;
4. If the machine does not start, must request the intervention of the
maintenance of mechanical and/or electric personnel to remove the eventual
cause and/or anomaly.
5. Only after the removal of the cause and/or anomaly and based on mechanical
and/or electric personnel opinion restart the machine according to the
switching-on procedure.

Instruction Manual Mixer Vertigo Mixer Technology srl pag.13
ORIGINAL ACCESSORIES ON REQUEST
RIF USO DENOMINAZIONE
DENSITÀ kg/m3
CODICE
1
Fine mortar
finishing
Tobacco replacement
250
3M00300201
White replacement
250
3M00300203
Blue replacement
180
3M00300204
Trowelling plaster,
fine mortar and
coarse
Red cheap sponge
160
3M00300210
Red sponge S16
160
3M00300211
Red sponge S20
200
3M00300212
Fine mortar
finishing
Blue sponge
300
3M00300213
Grey sponge
300
3M00300214
2 Scraping Bolded disk to scratch
/ 3M00300220
3 Traditional Coarse Trowel disk raw abs with
Velcro
/ 3M00302700
4 Smoothing plaster
and marbles
Spatula disk 4 blades
/
3M00302703
Spatula disk 6 blades
/
3M00302709
1
2
3
4

Instruction Manual Mixer Vertigo Mixer Technology srl pag.14
WARRANTY
1) Within the limits set forth by this warranty, the undersigned manufacturer
undertakes to repair all possible construction damages that may arise during the warranty
period of 12 (twelve) months for a daily use of 8 (eight) working hours. Such term shall
elapse as follows:
a) From the delivery date (Ref. transport document and sale invoice), if the
machine is sold directly to the Customer;
b) From the date given on the “Testing and Commissioning Certificate”, if the
Manufacturer or the Authorized Dealer performs the testing and commissioning of the
machine;
c) From the date of sale (Ref. transport document and sale invoice), if the machine is sold
directly by an Authorized Dealer on a "sale or return" basis; The obligations resulting from
the warranty decay in case of suspension or modification of the payment terms agreed
upon.
2) The warranty decays, if the purchaser does not duly observe the provisions
described in the “Instructions for Use and Maintenance” of the machine.
3) Remain excluded from the warranty: Failures and defects due to the normal tear of
those parts, which for their nature are subject to rapid and fast tear; electric
equipment; failures resulting from the use of tools and accessories not directly supplied
by the manufacturer.
4) In order to be able to exercise the warranty right, the purchaser has to inform the
manufacturer in case of defect detection immediately and, in any case, not later than 8
(eight) days from the detection date; moreover, it has to allow, if deemed necessary by
the same, the performance of the related inspections and repairing interventions.
5) The shipment of the faulty part, covered by the warranty, to the manufacturer for the
repairing or replacement of the same is at purchaser's charge. The warranty obligations,
as foreseen by this clause, are deemed fulfilled with the delivery to the purchaser of the
part duly repaired or replaced.
6) During the warranty period set forth by clause 1) labour costs, for the exclusive
duration of the intervention, are at manufacturer’s charge.
Should the repairing or replacement procedures be carried out where the machine is
installed, travel and lodging expenses of the personnel are at purchaser's charge.
7) Remain in any case excluded from the warranty, all faults caused by wrong
manoeuvre, negligence, fortuitous event or in any case all faults imputable to the user, in
person or through third parties, or when the purchaser has carried out modifications or
repairing interventions without the written consent of the manufacturer, independently
from the connection of such modifications or repairing interventions with the detected
faults.
8) It is explicitly agreed upon, that the manufacturer shall not be held responsible for any
liability following any possible damages that the purchasers may suffer resulting from loss
of or diminished production due to possible construction defects subject to this warranty.

Instruction Manual Mixer Vertigo Mixer Technology srl pag.15
Thank you for choosing our product
MIXER TECHNOLOGY srl
Via dei Carabinieri, 45, 36040
Torri di Quartesolo (VI) Italy
www.mixersrl.com