Modecom MC-WR11 User manual

1
MODECOM
QUICK START GUIDE
MC-wr11
MC-wr22
Wireless router

www.modecom.eu
2
Wireless router
Quick Start Guide 3
Chapter 1 Introduction 3
Features 3
1.2 Operation Environment 4
1.3 System Requirements 5
Chapter 2 Hardware Installation 5
2.1 Led indicators 5
2.2 Back Panel Features 5
2.3 Typical install 6
Chapter 3 - Quick Install Guide 7
3.1 TCP/IP Settings 7
3.2 Getting Started 8
3.3 Setup Wizard 9

3
Wireless router
Quick Start Guide
Latest versions of manuals, quick start guides, drivers and software are avail-
able on www.modecom.eu website.
IMPORTANT NOTE:
Provided technical specications are subject to change without prior notice. All
brand and product names mentioned in this manual are trademarks and/or reg-
istered trademarks of their respective holders.
© 2010 MODECOM S.A.
All rights reserved. Duplication and copying requires approval from copyright
holder.
Chapter 1 Introduction
Congratulations on your purchase of this outstanding Wireless Router. The
Wireless Router integrates 4-port switch, rewall, NAT-router and Wireless
Access Point. This product is specically designed for Home networks and
Medium or Small Corporation needs. It will allow you to connect your network
wirelessly better than ever, sharing Internet Access, les and fun, easily and
securely. It is easy to congure and operate even for users without wide ex-
perience with network devices. Instructions for installing and conguring this
product can be found the manual delivered with the product and also available
at www.modecom.eu website. Before you install and use this product, please
read this manual carefully to exploit all the functions of this product.
Features
WAN: Gateway / Bridge / WISP / Static IP / DHCP / PPPoE / PPTP / L2TP /
UPnP
LAN: RJ45 4port switch / DHCP Client, Server / Static DHCP / IP&MAC Bind
Wireless: Compliant with draft IEEE 802.11n standard (MC-WR22- 2T2R / MC-
WR11 – 1T1R)
Up to: 300Mbps (MC-WR22) / 150Mbps (MC-WR11) data transfer rates in IEEE
802.11n mode
Backward compatible with IEEE 802.11b/g
Supports both Infrastructure and Ad-Hoc Networking Modes
Work modes: AP / Client / WDS / AP+WDS / Universal Repeater (AP+Client)
Supports WPS, WPA2 (802.11i), WPA, WPA2/WPA Mixed, 802.1x advanced
security
Supports 64/128-bit WEP Data Encryption

www.modecom.eu
4
Wireless router
Quality of Service (QoS) - WMM, WMM-PS
Auto wireless transmission channel select for optimal performance
Wireless access control (MAC address lter)
Advanced Wireless control:
Fragment Threshold / RTS Threshold / Beacon Interval
Preamble Type: Long / Short
IAPP - Roaming (802.11f)
Protection / Aggregation / Short GI / WLAN Partition
RF Output Power control
Multiple BSSID
Dynamic DNS:
DynDNS.org / TZO / 3322.org
NAT:
NAT/NAPT IP sharing / DMZ / Port Forwarding / Port Trigger / UPnP
QoS:
Yes - IP (single or range) Grant MIN or MAX bandwidth
Firewall protection:
Ping Access on WAN / IGMP Proxy / Web Server Access on WAN / IPsec/
PPTP/L2TP VNP pass through /
Src MAC or IP Filter / URL Filter / Dst IP and Port Filter /
DoS Prevention:
Whole System Flood: SYN, FIN, UDP, ICMP
Per-Source IP Flood: SYN, FIN, UDP, ICMP
TCP/UDP Port Scan (High/Low Sensitivity)
ICMP Smurf, IP Land, IP Spoof, IP TearDrop, PingOfDeath, TCP Scan, TCP
SynWithData, UDP Bomb, UDP EchoChargen
Source IP Blocking (Block for a specied time)
System Management:
Access Schedule / NTP support / FW Upgrade / Save/Load Cong / Reboot /
User name and password management
1.2 Operation Environment
Dimensions: 202 (L) x 120 (W) x 31 (H)mm
Unit Weight: 324g
Power Input: 9V DC, 1A
Consumption: 13.5W(Max)
Storage Temperature: -40ºC ~70ºC

5
Wireless router
Operating Temperature : -10ºC ~50ºC
Storage Humidity: 5% ~95% RH Non-condensing
Operating Humidity: 10% ~90% RH Non-condensing
1.3 System Requirements
An Ethernet-Based Cable or DSL modem
10/100M Ethernet Card on PC
TCP/IP network protocol for each PC
RJ45 Twisted-pair cable
Internet browser: Microsoft Internet Explorer, Firefox, Opera or Chrome
Chapter 2 Hardware Installation
2.1 Led indicators
SYS/Power (Red): Flickering light indicates a proper connection to the power
supply.
While resetting the SYS LED will ash differently (shine for 2 seconds and stop
for 1 second).
WPS (Green): The Led will icker for about two minutes when WPS session
is active .
WLAN (Wireless LAN) (green): The LED is ickering during wireless activity.
LAN 1,2,3,4 (green): The Link/Act LED serves two purposes. If the LED is con-
tinuously illuminated, the Router is successfully connected to a device through
the corresponding port. If the LED is ickering, the Router is actively sending or
receiving data over that port.
WAN (Green):The Link/Act LED serves two purposes. If the LED is continu-
ously illuminated, the Router is successfully connected to a device through the
corresponding port. If the LED is ickering, the Router is actively sending or
receiving data over that port.
2.2 Back Panel Features

www.modecom.eu
6
Wireless router
LAN(1,2,3,4): 10/100Mbps RJ45 Auto-sensing. These four LAN ports are
where you will connect other network devices, such as PCs/Laptops, print
servers, remote hard drives, and anything else you want to put on your net-
work. If you connect this product with the Network adapter, Hub (or Switch)
correctly, the Router’s corresponding LED and the Adapter’s, Hub’s (or the
Switch) will illuminate.
WAN: 10/100Mbps RJ45 port. The WAN port is where you will connect
Cable/DSL Modem or other LAN.
RESET(WPS): The Reset Button has three functions, WPS, reboot and
Factory Default. When press it less than 2 second, it is WPS function and
the SYS LED will ash two minute (as long as WPS session is active); 2 to
5 seconds, the router will reboot; and more than 5 seconds, the router will
restore to factory default settings.
Power inlet: 9V DC, 1A Power supply.
2.3 Typical install
1. Make sure all devices, including your PCs, modem, and Router, are
turned on.
2. Using an Ethernet network cable, connect the LAN device or Ethernet
network port of the cable or DSL modem to the Router’s WAN port.

7
Wireless router
Chapter 3 - Quick Install Guide
3.1 TCP/IP Settings
Before you can access and congure router, you have to setup your net-
work adapter IP address. According to the following steps to obtain IP ad-
dress automatically from router DHCP Server, The following instruction set
up the computer running windows operation system.
Note: The router default IP address is 192.168.1.1
1. Click Start button and choose Settings, then click Control Panel.
2. Double click Network icon and select Conguration tab in the Network
window.
3. Choose the connection you want to use and click it with right mouse but-
ton and choose “Properties”.
4. Double click TCP/IP Protocol.
5. Make sure that option “Obtain IP address automatically” is chosen.
8. Click OK to complete the install procedure.
After all is successful, you can check the TCP/IP information via the follow-
ing command. Start -> run. Type cmd and in the window like the one below
enter command: ipcong /all.

www.modecom.eu
8
Wireless router
3.2 Getting Started
To access conguration panel open your web browser (MS Internet Explorer,
Firefox, Opera or Chrome) and type the router’s IP address: 192.168.1.1
Default User / Password: admin
If successful, you can see the status page.

9
Wireless router
3.3 Setup Wizard
Click on “Wizard”, it will guide you to setup your router in six simple steps.
Please follow the steps and complete the router conguration.
Step 1 - Setup Operation Mode
The router supports three operation modes, Gateway, Bridge and Wireless ISP.
And each mode is suitable for different use, please choose correct mode.

www.modecom.eu
10
Wireless router
Step 2 - Time Zone Settings
The Time Conguration option allows you to congure, update, and main-
tain the correct time on the internal system clock.
Time Zone Select: Select the Time Zone from the drop-down menu.
NTP Server: Select the NTP Server from the drop-down menu.
Step 3 - LAN Settings
Setup the IP address and Subnet mask for the LAN interface.
Step 4 - WAN Settings
The Router support ve access modes in the WAN side, please choose
correct mode according to your ISP Service.

11
Wireless router
Mode 1: DHCP Client
Select DHCP Client to obtain IP Address information automatically from
your ISP. This mode is commonly used for Cable modem services.
Mode 2: Static IP
Select Static IP Address if all IP information is provided to you by your ISP.
You will need to enter in the IP address, subnet mask, gateway address,
and DNS address(es) provided to you by your ISP. Each IP address entered
in the elds must be in the appropriate IP form, which are four numbers
(from 0 to 255) separated by dots (x.x.x.x). The Router will not accept the IP
address if it is not typed in this format.

www.modecom.eu
12
Wireless router
IP Address: Enter the IP address assigned by your ISP
Subnet Mask: Enter the Subnet Mask assigned by your ISP.
Default Gateway: Enter the Gateway assigned by your ISP.
DNS: Enter the DNS server assigned by your ISP.
Mode 3: PPPoE
Choose PPPoE (Point to Point Protocol over Ethernet) if your ISP uses a
PPPoE connection. Your ISP will provide you with a username and pass-
word.

13
Wireless router
User Name: Enter your PPPoE user name.
Password: Enter your PPPoE password.
Mode 4: PPTP
Choose PPTP (Point-to-Point-Tunneling Protocol ) if your ISP uses a PPTP
connection. Your ISP will provide you with IP information and PPTP Server
IP Address, of course it also includes a username and password.
IP Address: Enter the IP address.
Subnet Mask: Enter the subnet Mask.
Server IP Address: Enter the PPTP Server IP address provided by your
ISP.
User Name: Enter your PPTP username.
Password: Enter your PPTP password.

www.modecom.eu
14
Wireless router
Mode 5: L2TP
Choose L2TP (Layer 2 Tunneling Protocol) if your ISP uses a L2TP con-
nection. Your ISP should provide you with a username, password and all
necessary data.
IP Address: Enter the IP address.
Subnet Mask: Enter the subnet Mask.
Server IP Address: Enter the PPTP Server IP address provided by your
ISP.
User Name: Enter your PPTP username.
Password: Enter your PPTP password.
Step 5: WLAN Settings
Wireless Interface: If you do not want to use wireless, uncheck the box to
disable all the wireless connections.

15
Wireless router
Band: Supported standards: 802.11B, 802.11G, 802.11N and mixed. Please
choose its band according to standards used by devices which will be con-
nected to router.
Mode: Support AP, Client, WDS and AP+WDS mode.
Network TYPE: This type is only valid in client mode.
SSID: Service Set Identier, it identies your wireless network.
Channel width: Select 40MHz if you use 802.11n or 802.11n mixed mode,
otherwise 20MHz, it is default value.
Control Sideband: it is only valid when you choose channel width 40MHz.
Channel Number: Indicates the channel setting for the router. By default
the channel is set to 6.
Step 5: WLAN Security Settings
Secure your wireless network by turning on the WPA or WEP security fea-
ture on the router. This section you can set WEP, WPA, WPA2 and mixed
security mode.

www.modecom.eu
16
Wireless router
The following picture shows how to set the WEP security.
Key length: WEP supports 64-bit or 128-bit security key.
Key Format: User can enter key in ASCII or Hex format.
Key Setting: Enter the key, accordingly to chosen format.
The keys are used to encryption data transmitted in the wireless network.
Fill in the text box by following rules below:
• 64-bit: Input any 5 ASCII characters or 10 digit Hex values (in the “A-F”,
“a-f”, and
“0-9” range) as the encryption keys. It is advised to use digits and both low-
ercase and uppercase characters - for example: “012345aEfG”
• 128-bit: Input any 13 ASCII characters or 26 digit Hex values (in the
“A-F”, “a-f”, and “0-9” range) as the encryption keys. For example:
01234567890123456789aBcDEf”
The following picture shows how to set WPA-PSK security, you can select
WPA(TKIP), WPA2(AES) and Mixed mode.

17
Wireless router
Pre-Shared Key Format: Specify the format of the key, passphrase or hex.
Pre-Shared Key: Enter the key, accordingly to chosen format.
The keys are used to encryption data transmitted in the wireless network.
Fill in the text box by following rules below:
• 64-bit: Input any 5 ASCII characters or 10 digit Hex values (in the “A-F”,
“a-f”, and
“0-9” range) as the encryption keys. It is advised to use digits and both low-
ercase and uppercase characters - for example: “012345aEfG”
• 128-bit: Input any 13 ASCII characters or 26 digit Hex values (in the
“A-F”, “a-f”, and “0-9” range) as the encryption keys. For example:
01234567890123456789aBcDEf”
More information about conguration and advanced settings can be found
in the user’s manual delivered togeter with this device and available on
manufacturer’s website: www.modecom.eu

www.modecom.eu
18
Wireless router
Instrukcja instalacji 19
Rozdział 1 - Wprowadzenie 19
1.1 Specykacja 19
1.2 Środowisko pracy 20
1.3 Wymagania systemowe 21
Rozdział 2 - Instalacja 21
2.1 Diody LED 21
2.2 Panel tylny urządzenia 21
2.3 Typowa instalacja 22
Rozdział 3 - Skrócona instrukcja instalacji 23
3.1 Ustawienia TCP / IP 23
3.2 Wprowadzenie 24
3.3 Kreator konguracji (Setup Wizard) 25

19
Wireless router
Instrukcja instalacji
Najnowsze wersje instrukcji, sterowników i oprogramowania dostępne są na
stronie www.modecom.pl
WAŻNA INFORMACJA: Podane dane techniczne mogą ulec zmianie bez wcze-
śniejszego powiadomienia. Wszystkie znaki towarowe umieszczone w instrukcji
należą do ich właścicieli.
© 2010 MODECOM S.A. Wszelkie prawa zastrzeżone. Kopiowanie lub powie-
lanie wymaga zgody właściciela.
Rozdział 1 - Wprowadzenie
Gratulujemy zakupu tego wspaniałego routera. Bezprzewodowy Router MC-
WR22 / MC-WR11 łączy 4-portowy przełącznik, zaporę ogniową, router NAT
i punkt dostępowy sieci bezprzewodowej. Ten produkt został zaprojektowa-
ny specjalnie dla potrzeb sieci domowych oraz małych i średnich przedsię-
biorstw. Pozwala na łatwe i bezpieczne podłączenie do sieci innych urządzeń
zarówno bezprzewodowo jak i tradycyjnymi kablami Ethernetowymi. Jest łatwy
w konguracji i obsłudze nawet dla użytkowników bez szerokiego doświadcze-
nia w tym zakresie. Informacje dotyczące instalacji i konguracji tego produktu
można znaleźć w instrukcji obsługi dostarczonej razem z produktem oraz do-
stępnej na stronie www.modecom.pl. Przed instalacją i używaniem produktu,
należy uważnie przeczytać instrukcję by móc w pełni korzystać ze wszystkich
jego funkcji.

WAN: Brama (Gateway) / Most (Bridge) / WISP / Statyczny adres IP / DHCP /
PPPoE / PPTP / L2TP / UPnP
LAN: 4portowy przełącznik RJ45 / DHCP klient, serwer / Rezerwacja adresów
w DHCP / Przypisywanie adresów IP do MAC
Wireless: Wsparcie dla standardu IEEE 802.11n (MC-WR22 - 2T2R / MC-
WR11 – 1T1R)
 MC-WR22 do 300Mbps / MC-WR11 do 150Mbps
Wsteczna zgodność ze standardami IEEE 802.11b/g
Wsparcie trybów Infrastructure i Ad-Hoc
Tryby pracy: Punkt dostępowy (AP) / klient / WDS / AP+WDS / Universal
Repeater (AP+Client)
Zaawansowane szyfrowanie: WPS; WPA2 (802.11i), WPA, WPA2/WPA tryb
mieszany, 802.11x

www.modecom.eu
20
Wireless router
Szyfrowanie 64/128-bit WEP
Obsługa Quality of Service (QoS) - WMM, WMM-PS
Automatyczny wybór optymalnego kanału transmisji bezprzewodowej
Kontrola dostępu do sieci bezprzewodowej (ltr adresów MAC)
Zaawansowane ustawienia sieci bezprzewodowych:
Próg fragmentacji / Próg mechanizmu RTS / Częstotliwość wysyłania Beacon
Długość Preambuły (długa / krótka)
Roaming - IAPP (802.11f)
Regulacja mocy nadajnika
Multiple BSSID
Dynamic DNS: DynDNS.org / TZO / 3322.org
NAT: NAT/NAPT współdzielenie IP / Strefa zdemilitaryzowana (DMZ) / Przekie-
rowanie portów (Port Forwarding) / Wyzwalanie portów (Port Trigger) / UPnP
QoS: Tak - dla IP (pojedynczy lub zakres) Przydzielenie MIN lub MAX prze-
pustowości
Zapora Firewall: Ping Access on WAN / IGMP Proxy / Web Server Access on
WAN / IPsec/PPTP/L2TP VNP pass through / Filtr IP lub MAC / Flirt adresów
URL / Filtr źródłowych adresów IP I portów.
Ochrona przed atakami typu DoS:
Whole System Flood: SYN, FIN, UDP, ICMP
Per-Source IP Flood: SYN, FIN, UDP, ICMP
TCP/UDP PortScan (High/Low Sensitivity)
ICMP Smurf, IP Land, IP Spoof, IP TearDrop, PingOfDeath, TCP Scan, TCP
SynWithData, UDP Bomb, UDP EchoChargen
Blokowanie adresu IP (przez określony czas)

Harmonogram dostępu / synchronizacja czasu z serwerami NTP / Aktualizacja
oprogramowania / Zapisywanie/Przywracanie konguracji

Wymiary: 202 (dł.) x 120 (szer.) x 31 (wys.) mm; Waga: 324g
Zasilanie: 5V DC, 2A
Pobór mocy: 13.5W (max)
Temperatura otoczenia podczas pracy: -10 º C ~ 50 º C
Temperatura otoczenia podczas przechowywania: -40 º C ~ 70 º C
Wilgotność otoczenia podczas pracy urządzenia: 5% ~ 95% RH (bez konden-
sacji)