MonLines mySwing MSM05 User manual

EN
Be sure to read the assembly instructions before assembly - installation - commissioning!
This will protect you and prevent damage to your product.
Mounting instructions
MonLines mySwing MSM05
electric TV wall mount

EN
Mounting instructions MonLines mySwing MSM05 - Version no. 2021-10
2
Table of contents
Congratulations!
With the MonLines mySwing TV wall mount you have chosen a high quality product that offers you great benefits in the areas
of comfort and design at a high technical level.
The usability and service life of the MonLines mySwing mount depend on proper and professional installation as well as
operation, maintenance and observance of the instructions contained in this installation manual. Any electrical connections
that may be required should only be made by appropriate professionals.
The mySwing MSM05 mount is electrically operated. To avoid hazards and prevent wear of the installed electronics, please
read the instructions carefully.
1. Scope of delivery...............................................................................................................................................................3
2. Preparations before mounting.......................................................................................................................................4
3. Safety instructions............................................................................................................................................................4
4. Mounting.............................................................................................................................................................................5
5. Programming of positions...............................................................................................................................................9
6. Button assignment............................................................................................................................................................10
7. Troubleshooting................................................................................................................................................................11

EN
Versionsnr. 2016-08 - Montageanleitung TabLines TWE Tablet Wandeinbau
Version no. 2021-10 - Mounting instructions MonLines mySwing MSM05 3
1. Scope of delivery
wall mount with swivel arm
cable cover top cover 2x bottom cover
2x washer 4x
spirit level
mounting sheet cable sheath cable ties
frame
VESA adapter braces 2x
remote control
foam 2x
wrench
M6x35
4x
M6x12 M8x16 M5x25 M8 bolt
4x4x4x4x
M6x25 M8x25 M8x35 M8x60 plastic anchor
4x 4x 4x 6x 6x
M6 spacer M8 spacer covering cap
4x 4x 8x
infrared receiver
power supply
Additional tools required:

EN
Mounting instructions MonLines mySwing MSM05 - Version no. 2021-10
4
2. Preparations before mounting
1. Before assembly, check all components received against the scope of delivery. If any parts are damaged or missing,
please contact us by e-mail or phone.
2. Select an installation location with sufficient space to fully extend and retract the mount.
3. The mySwing bracket can be mounted with either left or right orientation. Depending on the selected orientation, the
mount can be swiveled either 90° left / 70° right or 90° right / 70° left (see the drawing below).
4. Only use suitable tools.
5. When mounting to a wood stud wall, be sure to center the screws in the wood stud. The use of a beam finder is strongly
recommended.
6. Make sure the wall is stable and load-bearing, as it must support the combined weight of the mount and TV.
7. Only use the screws supplied and do not overtighten them.
3. Safety instructions
1. Only use the mySwing mount indoors. Outdoor use may result in damage or injury.
2. Do not operate or mount the mySwing TV wall mount in a damp or wet environment.
3. Never operate the mySwing mount with a damaged power cord or plug. In case of damaged parts, please contact us by e-
mail or phone.
A A
B B
A: 0°
B: 0°
A: 0°
B: 0°
A: 90°
B: 0°
A: 90°
B: 0°
A: 90°
B: 90° R
A: 90°
B: 90° L
A: 90°
B: 70° R
A: 90°
B: 70° L
A: 160°
B: 90° R
A: 160°
B: 90° L
A: 160°
B: 70° L
A: 160°
B: 70° R
Joint A: max. 160°
Joint B: max. 70° L / 90° R
Joint A: max. 160°
Joint B: max. 90° L / 70° R
Left side mounting Right side mounting

EN
Versionsnr. 2016-08 - Montageanleitung TabLines TWE Tablet Wandeinbau
Version no. 2021-10 - Mounting instructions MonLines mySwing MSM05 5
4. Mounting
Step 1
Mount the frame on the swivel arm using the
enclosed mounting material.
Step 2
Mounting on a concrete or brick wall:
Use an M10 drill bit for the plastic anchors
and an M12 drill bit for the M8 bolts.
Mounting on a wooden wall:
No plastic anchors are required. Use an M5
drill bit for the drill holes.
Mounting on a wooden stud wall:
No plastic anchors are required. Use an M5
drill bit for the drill holes.
Attention: The mySwing TV wall mount can
only be mounted on firmly reinforced
wooden beams / wooden boards.

EN
Mounting instructions MonLines mySwing MSM05 - Version no. 2021-10
6
Step 3
Attach the mySwing TV mount to the wall
using the included mounting hardware.
Concrete or brick wall mounting
Wooden wall mounting
Wooden stud wall mounting

EN
Versionsnr. 2016-08 - Montageanleitung TabLines TWE Tablet Wandeinbau
Version no. 2021-10 - Mounting instructions MonLines mySwing MSM05 7
Step 4
Mount the two VESA adapter braces on your
TV using the included mounting hardware.
Select the appropriate screws and spacers
for your TV model.
Step 5
Mount the VESA braces to the frame of the
mySwing mount. Tighten the screws firmly,
but be careful not to overtighten them.

EN
Mounting instructions MonLines mySwing MSM05 - Version no. 2021-10
8
Step 6
Attach the infrared receiver directly to the bottom right of the front of the TV or to the wall near the TV using the double-
sided adhesive tape. Make sure that the infrared receiver is not blocked by the TV or other objects.
Attention: The signal strength of the remote control depends on the position of the infrared receiver. Place it in an accessible
location where it can receive the signal well.
Attach the 2 foam pads to the back of the TV for protection and stabilization. Route the infrared receiver cable and the power
cable along points 1 - 5 as shown in the drawing and secure both cables using the cable ties and covers provided. Place the
covers on the top and bottom of the holder respectively.
Attention: When attaching the cable ties, leave enough slack to allow the swivel arm to move to the left and right at the
maximum angle. The cable length should not affect the freedom of movement of the TV wall mount.

EN
Versionsnr. 2016-08 - Montageanleitung TabLines TWE Tablet Wandeinbau
Version no. 2021-10 - Mounting instructions MonLines mySwing MSM05 9
5. Programming of positions
1. When commissioning the mySwing TV wall mount, first define your preferred positions. Various selected angles can be
stored on the "IN", "OUT", "P1" and "P2" buttons on the remote control and automatically recalled by pressing the
button. Please note that the complete recall of an automatic movement process consists of several individual steps,
between which there may be a waiting time of a few seconds.
2. Fully extend the wall mount by pressing the "OUT" button (the preset default value is 90°). If you want to assign a new
angle to the "OUT" button, you can set this angle using the arrow keys. To do this, move the mount freely to the left or
right by holding down the respective arrow key until the desired position is reached. Releasing the arrow key stops the
movement. Now press "M" + "OUT" simultaneously to store the currently selected position on the "OUT" button. A
double signal tone is heard for confirmation. The default value is now overwritten with the currently selected position.
3. Additional preferred positions can be saved on the "P1" and "P2" buttons. To do this, set the desired position using the
arrow keys as described above and simultaneously press "M" + "P1" or "M" + "P2" to save the currently selected position
on the "P1" or "P2" button. A double signal tone is heard for confirmation. The default value is now overwritten with the
currently selected position.
4. By pressing the "IN" button, the mount moves back to its initial position (the preset default value is 0°). If you want to
assign a new angle to the "IN" button, you can also set this angle using the arrow keys. Then press "M" + "IN"
simultaneously to save the currently selected position on the "IN" button. A double signal tone is heard for confirmation.
The default value is now overwritten with the currently selected position.
Attention: The mySwing mount does not have a global reset function. If you want to change a saved position, overwrite it
separately with a new position as described in the sections above.

EN
Mounting instructions MonLines mySwing MSM05 - Version no. 2021-10
10
The mount moves to the position stored on "IN" (default value: 0°). By pressing the
"M" + "IN" buttons simultaneously, you can set a new position for "IN". A signal
tone is heard for confirmation.
The mount moves to the position stored on "OUT" (default value: 90°). By pressing
the "M" + "OUT" buttons simultaneously, you can set a new position for "OUT". A
signal tone is heard for confirmation.
Used in combination with "IN", "OUT", "P1" or "P2" to store positions on these
buttons.
The mount moves to the position stored on "P1". By pressing the "M" + "P1"
buttons simultaneously, you can set a new position for "P1" (default value: 30°).
The mount moves to the position stored on "P2". By pressing the "M" + "P2"
buttons simultaneously, you can set a new position for "P2" (default value: 60°).
Press and hold the left / right arrow key to swivel the mount to the left / right.
Releasing the key stops the movement. The maximum swivel range is limited in
both directions each by the distance of the swivel arm from the wall to avoid
collisions.
The mount automatically returns to the last previously selected position. This
angle is automatically saved and continuously updated.
6. Button assignment

EN
Versionsnr. 2016-08 - Montageanleitung TabLines TWE Tablet Wandeinbau
Version no. 2021-10 - Mounting instructions MonLines mySwing MSM05 11
Possible causes
7. Troubleshooting
Error Verification
The mount does not move. Dead battery /
defective remote control
No power connection
Incorrect operation
If the LED on the remote control
comes on but no signal tone is heard,
replace the battery. If the problem
persists, feel free to contact us by
email or phone.
Check the correct connection of the
power cord to the mount and the
power plug to the power outlet.
If you only hear a double signal tone
after pressing a position button, the
mount is already in the position
stored on this button.
After automatic return to the initial
position (0°), the mount performs a
slight jerking movement.
No infrared connection Check the position of the infrared
receiver and, if necessary, place it in
a more accessible location.
First use the arrow keys to move the
mount to a position slightly ahead of
the previously set initial position.
Now press "M" + "IN" simultaneously.
The current position is now stored as
the new initial position on the "IN"
button (see also section 5.4).
Overload

Mountinginstructions
TabLines
Am Marienhof 8
22880 Wedel
Germany
Contact us
Your MonLines dealer / specialist partner
Subject to changes
MonLines
Am Marienhof 8
22880 Wedel
Germany
E-Mail: [e-mail]
Web: www.monlines.com
Tel.: [phone] / 90387 - 0
Fax: [phone] / 90387 - 11
MonLines mySwing MSM05
electric TV wall mount