Moog Videolarm IP Ready IFDW75CN Instruction sheet

- 1 -
Before attempting to connect or operate this product,
please read these instructions completely.
Product
Instructions
IP Ready™Series
IFDW75CN & IFDP75CN
81-IN5367
08/10/07

- 2 -
!
CAUTION
RISK OF
ELECTRIC SHOCK!
CAUTION: TO REDUCE THE RISK OF
ELECTRICAL SHOCK, DO NOT EXPOSE
COMPONENTS TO WATER OR MOISTURE.
SAFETY PRECAUTIONSIMPORTANT SAFEGUARDS
1. ReadInstructions-Allthesafetyandoperating instructionsshouldberead
before the unit is operated.
2. RetainInstructions-Thesafetyandoperatinginstructionsshouldberetained
for future reference.
3. HeedWarnings-Allwarningsontheunitandintheoperatinginstructions
should be adhered to.
4. FollowInstructions-Alloperating&userinstructionsshouldbefollowed.
5. ElectricalConnections-Onlyaqualifiedelectricianshouldmakeelectrical
connections.
6. Attachments-Donotuseattachmentsnotrecommendedbytheproduct
manufacturer as they may cause hazards.
7. Cable Runs - All cable runs must be within permissible distance.
8. Mounting-Thisunitmustbeproperlyandsecurelymountedtoasupporting
structure capable of sustaining the weight of the unit. Accordingly:
a. Installation should be made by a qualified installer.
b. Installation should be in compliance with local codes.
c. Careshouldbeexercisedtoselectsuitablehardwaretoinstalltheunit,
takingintoaccountboththecompositionofthemountingsurfaceand
theweightofthe unit.Besuretoperiodicallyexaminetheunitandthe
supportingstructuretomakesurethattheintegrityoftheinstallation
is intact. Failure to comply with the foregoing could result in the unit
separatingfromthesupportstructureandfalling,withresultantdamages
or injury to anyone or anything struck by the falling unit.
UNPACKING
Unpackcarefully.Electroniccomponentscanbedamagedifimproperlyhandled
ordropped. Ifanitemappearstohavebeendamagedinshipment,replaceit
properly in its carton and notify the shipper. Be sure to save:
1. Theshippingcartonandpackagingmaterial. Theyarethesafest materialin
which to make future shipments of the equipment.
2. These Installation and Operating Instructions.
!
Thelightningflashwithanarrowheadsymbol,withinan
equilateraltriangle,isintendedtoalertthe user to the
presenceofnon-insulated"dangerousvoltage"withinthe
product'senclosurethatmaybeofsufficientmagnitude
to constitute a risk of electric shock to persons.
Theexclamationpoint within anequilateraltriangle is
intendedtoalerttheusertopresenceofimportantoperating
andmaintenance(servicing)instructionsintheliterature
accompanying the appliance.
24 HOUR TECHNICAL SUPPORT
1-800-554-1124
SERVICE
Iftheuniteverneedsrepairservice,customershouldcontactVideolarm
(1-800-554-1124) for return authorization & shipping instructions.
TECHNICAL SUPPORT
Videolarmhasset-upa24hourtechnicalsupportlinefortheircustomers.
LIMITED WARRANTY FOR VIDEOLARM INC. PRODUCTS
VIDEOLARM INC. warrants this Product to be free from defects in material or workmanship, as follows:
PRODUCT CATEGORY PARTS LABOR
All Enclosures and Electronics Three (3) Years Three (3) Years
Pan/Tilts Three (3) Years **6 months if used in autoscan Three (3) Years **6 months if used in autoscan
Poles/PoleEvators Three (3) Years Three (3) Years
Warrior/Q-View/I.R. Illuminators Five (5) Years Five (5) Years
Controllers Three (3) Years Three (3) Years
Power Supplies Three (3) Years Three (3) Years
Accessory Brackets Three (3) Years Three (3) Years
Duringthelaborwarrantyperiod,torepairtheProduct,Purchaserwilleitherreturnthedefectiveproduct,freightprepaid,ordeliverittoVideolarmInc.DecaturGA.
TheProducttoberepairedistobereturnedineitheritsoriginalcartonorasimilarpackageaffordinganequaldegreeofprotectionwithaRMA#(ReturnMaterials
Authorizationnumber)displayedontheouterboxorpackingslip.ToobtainaRMA#youmustcontactourTechnicalSupportTeamat800.554.1124,extension101.
VideolarmwillreturntherepairedProductfreightprepaidtoPurchaser.VideolarmisnotobligatedtoprovidePurchaserwithasubstituteunitduringthewarranty
period or at any time. After the applicable warranty period, Purchaser must pay all labor and/or parts charges.
The limited warranty stated in these product instructions is subject to all of the following terms and conditions:
1. NOTIFICATION OF CLAIMS: WARRANTY SERVICE: If Purchaser believes that the Product is defective in material or workmanship, then written notice
withanexplanationoftheclaimshallbegivenpromptlybyPurchasertoVideolarmbutallclaimsforwarrantyservicemustbemadewithinthewarrantyperiod.
IfafterinvestigationVideolarmdeterminesthatthereportedproblemwasnotcoveredbythewarranty,PurchasershallpayVideolarmforthecostofinvestigating
theproblematitsthenprevailingperincidentbillablerate.NorepairorreplacementofanyProductorpartthereofshallextendthewarrantyperiodastotheentire
Product.The specific warranty on the repaired part only shall be in effect for a period of ninety (90) days following the repair or replacement of that part or the
remaining period of the Product parts warranty, whichever is greater.
2. EXCLUSIVE REMEDY: ACCEPTANCE: Purchaser’s exclusive remedy and Videolarm’s sole obligation is to supply (or pay for) all labor necessary to repair
any Product found to be defective within the warranty period and to supply, at no extra charge, new or rebuilt replacements for defective parts.
3. EXCEPTIONS TO LIMITED WARRANTY: Videolarm shall have no liability or obligation to Purchaser with respect to any Product requiring service during
thewarrantyperiodwhichissubjectedtoanyofthefollowing:abuse,improperuse:negligence,accident,lightningdamageorotheractsofGod(i.e.,hurricanes,
earthquakes),modification,failureoftheend-usertofollowthedirectionsoutlinedintheproductinstructions,failureoftheend-usertofollowthemaintenance
proceduresrecommendedbytheInternationalSecurityIndustryOrganization,writteninproductinstructions,orrecommendedintheservicemanualfortheProduct.
Furthermore,Videolarmshallhavenoliabilitywhereascheduleisspecifiedforregularreplacementormaintenanceorcleaningofcertainparts(basedonusage)
andtheend-userhasfailedtofollowsuchschedule;attemptedrepairbynon-qualifiedpersonnel;operationoftheProductoutsideofthepublishedenvironmental
and electrical parameters, or if such Product’s original identification (trademark, serial number) markings have been defaced, altered, or removed. Videolarm
excludesfromwarrantycoverageProductssoldASISand/orWITHALLFAULTSandexcludesusedProductswhichhavenotbeensoldbyVideolarmtothePurchaser.
Allsoftwareandaccompanyingdocumentationfurnishedwith,oraspartoftheProductisfurnished“ASIS”(i.e.,withoutanywarrantyofanykind),exceptwhere
expressly provided otherwise in any documentation or license agreement furnished with the Product.
4. PROOF OF PURCHASE: The Purchaser’s dated bill of sale must be retained as evidence of the date of purchase and to establish warranty eligibility.
DISCLAIMER OF WARRANTY EXCEPT FOR THE FOREGOING WARRANTIES, VIDEOLARM HEREBY DISCLAIMS AND EXCLUDES ALL OTHER WARRANTIES, EXPRESS OR IMPLIED,
INCLUDING,BUTNOTLIMITEDTOANYAND/ORALLIMPLIEDWARRANTIESOFMERCHANTABILITY,FITNESSFORAPARTICULARPURPOSEAND/ORANYWARRANTYWITHREGARDTOANYCLAIM
OFINFRINGEMENTTHATMAYBEPROVIDEDINSECTION2-312(3)OFTHEUNIFORMCOMMERCIALCODEAND/ORINANYOTHERCOMPARABLESTATESTATUTE.VIDEOLARMHEREBYDISCLAIMS
ANYREPRESENTATIONSORWARRANTYTHATTHEPRODUCTISCOMPATIBLEWITHANYCOMBINATIONOFNON-VIDEOLARMPRODUCTSORNON-VIDEOLARMRECOMMENDEDPRODUCTS
PURCHASER CHOOSES TO CONNECT TO PRODUCT.
LIMITATION OF LIABILITY THE LIABILITY OF VIDEOLARM, IF ANY, AND PURCHASER’S SOLE AND EXCLUSIVE REMEDY FOR DAMAGES FOR ANY CLAIM OF ANY KIND WHATSOEVER,
REGARDLESSOFTHELEGALTHEORYANDWHETHERARISINGINTORTORCONTRACT,SHALLNOTBEGREATERTHANTHEACTUALPURCHASEPRICEOFTHEPRODUCTWITHRESPECTTOWHICH
SUCHCLAIMISMADE.INNOEVENTSHALLVIDEOLARMBELIABLETOPURCHASERFORANYSPECIAL,INDIRECT,INCIDENTAL,ORCONSEQUENTIALDAMAGESOFANYKINDINCLUDING,BUTNOT
LIMITED TO, COMPENSATION, REIMBURSEMENT OR DAMAGES ON ACCOUNT OF THE LOSS OF PRESENT OR PROSPECTIVE PROFITS OR FOR ANY OTHER REASON WHATSOEVER.

- 3 -
!
!
ELECTRICAL SPECIFICATIONS (INDOOR ONLY):
Power 24Vac, Class 2 Only
Total Power: 52 watts
Camera Power: 52 watts MAX
NOTE: This unit is designed for operation in an
upright position. Installing the housing
upside down may cause damage to
the internal equipment, and will void the
warranty.
Be sure the bracket is properly and securely mounted
to a supporting structure capable of rigidly holding
the weight of the entire unit.
GENERAL INSTRUCTIONS:
Tools Required: .100" Flat Head Screwdriver
Phillips Head Screwdriver
IFDW75CN, IFDP75CN
IP Ready Network Housing
IP Ready Network Housing with wall mount or pendant
mounting, ready for standard IP PTZ cameras.
ASSEMBLING THE UNIT:
1. Remove content from all boxes.
Contents should include:
Main Housing Assembly
Either with wall mount or pendant bracket
Dome Assembly - Clear or Tinted
Do not remove the protective lm until the product is
assembled and installed.
3 Packet Assemblies

- 4 -
INSTALLATION OF PTZ CAMERA
See model for specic instruction.
Listed on the following pages are the specic instructions
for each of the individual network cameras. See specic
instruction for the model that matches the unit you have.
INDEX OF CAMERAS
AXIS 213 5
AXIS 214 6
AXIS 231D/232D 7-9
CANON VB-C10R 10
CANON VB-C50iR 11
CANON VC-C4R / VC-C50iR 12
ELMO PTC-200C 13
ELMO PTC-201 14
ELMO PTC-400C 15
ELMO PTC-401 16
JVC VN-C30U 17
JVC VN-C625U / TK-625U 18
JVC VN-C655U 19
PANASONIC BB-HCM381/580/581 & KX-HMC280 20
PIXORD 261 / 262 21
SONY SNCRZ25 22
SONY SNCRZ30 23
SONY SNCRZ50 24
TOSHIBA IK-WB21A 25
AXIS 233D COMPATIBILITY
Due to the high-denition zoom feature of the Axis 233D camera, Videolarm's standard FDW domes are not compatible. For ap-
plications where the full 35x high-powered zoom is requried, Videolarm has developed four special models of its FusionDome which
incorporate an enhanced optically clear acrylic dome: FDW75C2N/AC, FDP75C2N/AC, IFDW75CN/AC, IFDP75CN/AC. For further
information on these products and the compatibiilty of the Axis 233D camera system, please contact a Videolarm representative at
[phone].

- 5 -
INSTALLING QUICK RELEASE BRACKETS
AXIS 213
2539 Mounting Plate:
1. Install the camera to the 2539 mounting plate using
(2) 10-32 screws and lockwashers provided.
2. The Axis 213 camera requires 3.5" of spacing for optimal
position within the housing. Use (4) 2" spacer(s), plus
(4) 1" spacer(s) and (4) ½" spacer(s) provided in the (2)
hardware packets.
Attach camera using these (2) holes
½"
1"
2"
Captive Screw
(3) screws
in housing
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.

- 6 -
INSTALLING QUICK RELEASE BRACKETS
AXIS 214
2685 Mounting Plate:
Attach camera using these (3) holes
1. Install the AXIS 214 camera to the 2685 mounting
plate using the (3) 3mm x 12mm bolt and lock washers
provided.
2. The AXIS 214 camera requires 2” of spacing for optimal
position within the housing. Use the 4 (2”) spacers
provided in the packet.
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
2"

- 7 -
INSTALLING QUICK RELEASE BRACKETS
AXIS 231D/232D
2685 Mounting Plate:
Attach camera using these (3) holes
1. The AXIS 231D/232D mounts to the 2685 mounting plate
using the (3) locking pins on the base of the pan tilt.
2. Hold pan/tilt with dome facing down, and nd “tab” on
the bottom of the unit. Loosen the screw which is to the
right of the tab by approximately 5 turns.
3. Position the locking pins and locking screw over the key
hole slots and twist clockwise. Secure locking screw.
4. The AXIS 231D/232D cameras require ½” of spacing for
optimal position within the housing. Use (4) ½” spacer
provided in the packet.
5. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
6. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
½"
Keyhole slot (3)
Loosen screw
Locking screw
Small keyhole
slot
Locking pins

- 8 -
Installing the Axis 231D/232D Camera (cont.)
7. Housing with 2685 mounting plate installed.
8. Since the 231D/232D camera operates on 24vac, the power
board that is located inside the housing is not needed. The
remove the power board, start by loosening the screws
on the terminal block and disconnect the orange and red
wires.
9. With a Phillips head screwdriver remove the (4) machine
screws holding the power board to the base bracket.
10. Locate the connector
block, which is included
with the camera. Then
locate the connector
block bracket, which
is included with the
housing. Attach the
block to the bracket as
shown in the following
diagram. Use the M3
screws and washers
that are located in the
housing packet.
11. Attach the connector block assembly to the housing using
(1) 6-32x3/8” screw and star washer located in the housing
packet.
Machine screws (4)
Base Bracket

- 9 -
Installing the Axis 231D/232D Camera (cont.) 13. To manage the input cable running from the connector
block to the camera use the (2) cable tie mounts and
cable ties that are located in the housing packet.
12. Make wiring connections to connector block assembly per
camera instructions.
For Model 25733 only
CONTROL
RJ45 Ethernet Connector
ALARMS
1 Alarm 1 Blue
2 Alarm 2 Violet
3 Alarm 3 Gray
4 Common White
POWER
1 Camera Power (24VAC) Red
2 Camera Power (24VAC) Orange
14. Now grab the camera assembly and connector the RJ45
cable and the input cable to the camera (see diagram
opposite).
15. Now attach the camera assembly to the housing by sliding
the (3) open screw slots over the screws in the housing.
Slide the bracket forward, and the tighten the captive
screw on the bracket.
Open screw slots
Captive screw
Cable Tie Mounts
Cable Ties

- 10 -
INSTALLING QUICK RELEASE BRACKETS
CANON VB-C10R
2539 Mounting Plate:
1. Install the camera to the 2539 mounting plate using
(2) 10-32 screws and lockwashers provided.
2. The Canon VB-C10R camera requires 4" of spacing for
optimal position within the housing. Use (4) 2" spacer(s),
plus (4) 1" spacer(s) and (4) ½" spacer(s) provided in the
(2) hardware packets.
Attach camera using these (2) holes
1"
2"
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
Captive Screw
(3) screws
in housing
½"

- 11 -
INSTALLING QUICK RELEASE BRACKETS
CANON VB-C50iR
2539 Mounting Plate:
1. Install the camera to the 2539 mounting plate using
(2) 10-32 screws and lockwashers provided.
2. The Canon VB-C50iR camera requires 3.5" of spacing for
optimal position within the housing. Use (4) 2" spacer(s),
plus (4) 1" spacer(s) and (4) ½" spacer(s) provided in the
(2) hardware packets.
Attach camera using these (2) holes
½"
1"
2"
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
Captive Screw
(3) screws
in housing

- 12 -
INSTALLING QUICK RELEASE BRACKETS
CANON VC-C4R / VC-C50iR
2539 Mounting Plate:
1. Install the camera to the 2539 mounting plate using
(2) 10-32 screws and lockwashers provided.
2. The Canon VC-C4R / VC-C50iR camera requires 4" of
spacing for optimal position within the housing. Use (4)
2" spacer(s), plus (8) 1" spacer(s) provided in the (2)
hardware packets.
Attach camera using these (2) holes
1"
2"
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
Captive Screw
(3) screws
in housing
1"

- 13 -
INSTALLING QUICK RELEASE BRACKETS
ELMO PTC-200C
Mounting plate for this unit is included in the housing
packet. Remove existing mounting plate installed in the unit
before proceeding.
2539 Mounting Plate:
1. Place the camera onto the quick release bracket using
the (4) metric 3M Phillips head screws provided with the
kit.
Attach camera using these (4) holes
½"
1"
2"
2. The Elmo PTC-200C camera requires 3.5" of spacing for
optimal position within the housing. Use (4) 2" spacer(s),
plus (4) 1" spacer(s) and (4) ½" spacer(s) provided in the
(2) hardware packets.

- 14 -
INSTALLING QUICK RELEASE BRACKETS
ELMO PTC-201
Mounting plate for this unit is included in the housing
packet. Remove existing mounting plate installed in
the unit before proceeding.
2539 Mounting Plate:
1. Place the camera onto the quick release bracket using
the (4) metric 3M Phillips head screws provided with the
kit.
Attach camera using these (4) holes
½"
2"
2. The Elmo PTC-201 camera requires 2½" of spacing for
optimal position within the housing. Use (4) 2" spacer(s)
plus (4) ½" spacer(s) provided in the (2) hardware
packets.
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.

- 15 -
INSTALLING QUICK RELEASE BRACKETS
ELMO PTC-400C
Mounting plate for this unit is included in the housing
packet. Remove existing mounting plate installed in the unit
before proceeding.
2539 Mounting Plate:
1. Place the camera onto the quick release bracket using
the (4) metric 3M Phillips head screws provided with the
kit.
Attach camera using these (4) holes
½"
1"
2"
2. The Elmo PTC-400C camera requires 3.5" of spacing for
optimal position within the housing. Use (4) 2" spacer(s),
plus (4) 1" spacer(s) and (4) ½" spacer(s) provided in the
(2) hardware packets.
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.

- 16 -
INSTALLING QUICK RELEASE BRACKETS
ELMO PTC-401
Mounting plate for this unit is included in the housing
packet. Remove existing mounting plate installed in
the unit before proceeding.
2539 Mounting Plate:
1. Remove the mounting plate from the camera and
place it onto the quick release bracket using the (4)
metric 3M Phillips head screws provided with the kit.
Then place the ELMO mounting plate back onto the
Elmo PTC-401C.
Attach camera using these (4) holes
2"
2. In the packet, there will be a number of 2 inch and 1
inch spacers. Take four of the 1 inch spacers and screw
them onto the spacers that are on the base bracket
(to make a 3 inch spacer). Place two 8/32 X sPhilips
head screws on the three inch spacer in the dome. Be
sure to place the screws so they line up with the two
open screw slots on the quick release bracket. Place
the Elmo PTC-401C pan/tilt and quick release bracket
in the housing, sliding the two open screw slots over the
screws in the housing. Slide the bracket forward, and
then tighten the captive screw on the bracket.
1"

- 17 -
INSTALLING QUICK RELEASE BRACKETS
JVC VN-C30U
2539 Mounting Plate:
1. Remove the mounting plate from the camera and
place it onto the quick release bracket using the (3)
metric 3M Phillips head screws provided with the kit.
Then place the mounting plate back onto the
JVC VN-C30U.
Attach camera using these (3) holes
½"
2"
2. In the packet, there will be a number of 2 inch and
½ inch spacers. Take four of the ½ inch spacers and
screw them onto the spacers that are on the base
bracket (to make a 2½ inch spacer). Place two 8/32
X sPhilips head screws on the two and a half inch
spacer in the dome. Be sure to place the screws so
they line up with the two open screw slots on the quick
release bracket. Place the JVC VN-C30U pan/tilt and
quick release bracket in the housing, sliding the two
open screw slots over the screws in the housing. Slide
the bracket forward, and then tighten the captive
screw on the bracket.

- 18 -
INSTALLING QUICK RELEASE BRACKETS
JVC VN-C625U / TK-625U
Attach camera using these (4) holes
1. Remove plastic cover (1 screw).
2. Detach Q/R Bracket from camera.
2630 Mounting Plate:
3. The JVC VN-C625U / TK-625U requires a total of 2” of
spacing to properly position the camera within the
housing.
4. Attach (4) 1” spacers to the 2630 mounting plate in the
position shown. Secure with (4) 6 x 32 x .5” screws and
lock washers.
5. Place (4) additional spacers on the main bracket as
shown in picture above.
6. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
7. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
1"
1"

- 19 -
INSTALLING QUICK RELEASE BRACKETS
JVC VN-C655U
2630 Mounting Plate:
1. Place the camera onto the quick release bracket using
the (4) metric 3M Phillips head screws provided with the
kit.
Attach camera using these (4) holes
½"
1"
2. The JVC VN-C655U requires 1 ½ “ to properly position
the camera within the housing. Use (4) 1” spacers and
(4) ½” spacer provided in the (2) hardware packets.
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.
5.
!
NOTE: The JVC VN-C655U is an 18Vdc unit.
Check instructions for connecting 18Vdc
camera (page 26).

- 20 -
½"
1"
2"
INSTALLING QUICK RELEASE BRACKETS
PANASONIC BB-HCM381/580/581 & KX-HMC280
2539 Mounting Plate:
Attach camera using this hole
1. Install the camera to the 2539 mounting plate using the
¼ x 20, washer and lockwasher provided.
2. The Panasonic BB-HCM381/580/581 & KX-HMC280
requires 3½" of spacing to properly position the camera
within the housing.
3. Place (3) 8 x 32 x s Phillips head screws on the top
of the spacer as shown above. Be sure to place the
screws so that they line up with the open slots on the
mounting plate.
4. Slide the mounting plate with camera into position on
top of spacers. Secure 3 screws and captive fastener.