Morgan MBH-GC522C User manual

U ER MANUAL
Built-in
Hob (CLA 3)
MBH-GC522C(BK)
MBH- D572(BK)
MBH-553(BK)
E-mail: [e-mail]
www.morgan.my
Market Expansion
Services by
www.dksh.com.my
facebook.com/morganappliances

2 3
C O N T E N T S
4
5
5
6
6
7
8
9
9
10
11
Parts Identification & Specifications
Precaution Logo
Thank You For Using organ Built-in Hob
Caution
Operation Instructions
Installation Instructions
Safety Instrutions
Illustrations
Cleaning
Trouble Shooting
Warning

4
PARTS IDENTIFICATION & SPECIFICATIONS
PARTNAME
1. Wok Stand
2. Pan Stand
3. Safety Valve*
4. Outer Cap
5. Inner Cap
6. Decorative Cover
7. Anti-Spillage Tray
8. Knob
9. Bottom Base
10. Label
11. Glass Top
12. Semi-rapid Burner
13. Sparker
inimum allowable diameter of pan:wok burner 130mm
Semi-rapid wok burner: 80mm
Battery: R20 Battery x 1, DC 1.5V
PRECAUTION LOGO
THANK YOU FOR USING MORGAN BUILT-IN HOB
5
Do not place anything in between pan and pan support that
may seriously damage the hob.
Do not remove the pan support and enclose the burners.
This will concentrate the flame and deflect the heat onto the
hotplate.
1. If gas leaks, switch-off the stopcock by turning the knob to “off” position and open all
windows for ventilation. Do not light a match or use a lighter. Refrain from operation
electric switches. Contact authorized technician immediately.
2. Please use the specified gas. Incorrect gas usage will cause abnormal burning and
lead to danger.
3. Please use good quality rubber hose and ensure connection being secured properly.
Ensure that the hose does not pass on top of the hob. Do not depress or bend the
hose.
Do not use large or heavy pots which can bend on the pan
support and deflect the flame onto hotplate.
Position pan centrally over burner so that it is stable. Do not
let pan in overhang position.
Use only wok support supplied or recommended by the hob
manufacturer.
BUILT-IN HOB
Model MBH-GC522C(BK) / MBH-SD572(BK)* MBH-553(BK)
Category I3B/P(30) I3B/P(30)
Gas Type Butane (G30), Propane (G31) or their mixtures Butane (G30), Propane (G31) or their mixtures
Gas Pressure 28-30mbar 28-30mbar
Countries of Destination MY MY
Nominal heat input
Work burner: 4.0kW (291g/h) x 2
Work burner: 4.0kW (291g/h) x 2
Semi-rapid burner: 1.4kW (102g/h)
Total: 8.0kW (582g/h) Total: 9.4kW (684g/h)
Electrical Voltage DC 1.5V DC 1.5V
Country of Origin Made in China Made in China
This appliance shall be installed in accordance with the regulations in force and only used in a well ventilated space.
ead the instructons before installing or using this appliance.
13
6
3
2
1
7
8
11 5
4
9
10
13
6
2
1
7
8
11
12 5
4
9
10

1. Please use the specified gas type.
2. When using the hob, please ensure proper ventilation in the kitchen.
3. Installation and servicing should be carried out by authorized personnel only.
4. Use only low pressure regulator for this appliance. (as shown in figure 4)
6 7
CAUTION INSTALLATION INSTRUCTIONS
OPERATION INSTRUCTIONS
1. This hob unit must be installed by a qualified technician to avoid hazard.
2. Cut the opening 680mm x 380mm (rounded edges with radius R50mm) as shown in
figure 1.
3. Use new hose and new hose clip (screw type) for installation of your hob unit. (as
shown in figure 2).
4. The glass top plate should fit the top of the bench properly.
5. After installation, test with soapy water to ensure no gas leakage. (as shown in
figure 3)
Low Pressure
Regulator
High Pressure
Regulator
Figure 4
680mm
380mm
R50
NOTE: Warranty void if
hole measurement for
installation of hob unit is not followed.
Gas Inlet Area
To Gas
Regulator
Figure 1
Figure 2
Figure 3
6. Hose should not exceed 2m.
7. Install the rubber hose.
8. Do not bend, twist or stretch the hose.
• The position of the corresponding gas burner is indicated on each control knob.
• The burner can be regulated with the corresponding control knob by using the
following setting:
HOB ITH ELECTRONIC IGNITION
• Insert the battery into the battery box provided.
(The battery box is located at the underside of the cooker).
• Turn on the gas supply.
• Depress the knob and turn it anti-clockwise 90º to maximum
flame position, a continuous clicking sound will be heard to
ignite the hob. Release the knob when the burner has been lit.
• Turning the knob clockwise to "OFF" position, a click sound will
be heard, the gas supply is shut off and the flame will distinguish.
FOR HOB ITH ELECTRONIC IGNITION & SAFETY DEVICE ONLY
• Electronic ignition & safety device is equipped with automatic shut off device. When the
flame is distinguished due to blowing of wind or overflow of spill, this protective device
will cut off the gas supply for safety protection.
• Insert the battery into the battery box provided (The battery box is located at the
underside of the cooker).
• Turn on the gas supply.
• Depress the knob and turn it anti-clockwise 90º to maximum flame position for 5-8
seconds, a continuous clicking sound will be heard to ignite the cooker. Release the
knob when the burner has been lit.
• Turning the knob clockwise to "OFF" position, a click sound will be heard, the gas
supply is shut off and the flame will distinguish.
CAUTION: if the flame extinguishes accidentally, turn off all gas supply and wait for 1
minute before attempting to re-ignite.

8
INSTALLATION INSTRUCTIONS
SAFETY INSTRUCTIONS
1. Please use the specified gas type for the hob.
2. Please use the specified rubber hose for gas supply which does not break due to
aging. The hose must not be in contact with any part of the hob. (it is recommended to
change the gas inlet hose every 2 years.)
3. Before using, please check to ensure that the burners, copper caps and wok stands
are placed in proper position.
4. Do not use the hob to dry clothing or place combustible objects near the hob.
5. During cooking, please maintain proper ventilation in the kitchen and avoid direct
strong wind blowing to the hob.
6. Do not seal the cabinet door. When using the hob, ensure supply of fresh air into the
cabinet.
7. Burner heads, copper caps and wok stands are hot after used. Please do not touch
them.
8. If gas leaks, switch off the stopcock by turning the knob to “off” position and open all
windows for ventilation. Do not operate electric switches, insert or remove plug from
the socket, and do not light a flame.
9. Do not spray aerosols in the vicinity of this hob while it is in operation. Some
propellant gas may produce corrosive vapour when heated.
10. Flammable materials should not be stored in drawers or cupboards which are located
below this hob.
9
ILLUSTRATIONS
1. There could be air trapped in the gas pipe in a new hob or when left unuse for a
period of time. The burner may not lit at first ignition. Please repeat the ignition
process to let out the air in the pipe until it is lighted.
2. In case of yellow flame or backfire during burning, adjust the air ventilation plate
situated at the hob base until the flame is normal (there are air-vents for both of the
inner ring and outer ring flame).
CLEANING
• Allow glass hob to cool down before cleaning. The glass plate is best cleaned with
cloth and warm soapy water.
• Caustic solutions, washing soda, aerosol spray cleaners, bleach and some biological
cleaners are detrimental to some finishing. Do not apply them onto burners and caps.
• Do not put burner caps into dishwasher.
• Remove spillage from the anti-spillage tray before cleaning. Control knobs can be
pulled off for cleaning.
• When re-assembling the anti-spillage tray, always ensure that it is located correctly
over the spark electrode. Care should be taken to keep the electrode clean and avoid
damage to the porcelain insulator when removing the anti-spillage tray during
cleaning.
These instructions are only valid if the country symbol appears on the appliance. If the
symbol does not appear on the appliance, it is necessary to refer to the technical instructions
which will provide the necessary instructions concerning modification of the appliance to the
conditions of use of the country.
“Prior to installation, ensure that the local distribution conditions (nature of the gas and gas
pressure) and the adjustment of the appliance are compatible. The adjustment conditions for
this appliance are stated on the label.” “This appliance is not connected to a combustion
products evacuation device. It shall be installed and connected in accordance with current
installation regulations. Particular attention shall be given to the relevant requirements
regarding ventilation.
Do not use cooking vessels on the hotplate that overlap it’s edges
Do not use hob guards
1. The underside of the hob must have a clearance of minimum 40cm. Do not seal
completely. The door of the cabinet must have ventilation blinds with ventilation area
of not less than 200 cm2or 10cm (H) x 20cm (W)
at the bottom of both of the cabinet doors.
2. Please use specified rubber hose.
3. Do not place gas cyclinder underneath the
hob. The rubber hose must not exceed 2m in
length.
4. Observe minimum clearance surrounding the
hob (more than 150mm from the wall and
more than 1000mm for vertical distance).
(Refer the diagram)
20cm
1000mm
hob to hood
10cm
Ventilation
Blind
150mm
right
alignment
150mm
left
alignment

10
TROUBLE SHOOTING
FAULT CAU E REMEDIE
Failed Ignition The regulator is not turned on. Turn off the hob and turn on the regulator.
Wrong insertion of battery. Insert the battery in correct position.
Battery is weak. Change a new battery.
Air exist in the pipe. epeat the ignition to let out the air from
the pipe.
The rubber hose is bent. Straighten it or replace it with a new hose.
Sparker is dirty. Clean the sparker.
Distance between sparker and burner Adjust the distance between 4 – 6mm.
cap is too wide.
Burner cap and sparker are wet. Dry the burner cap and sparker with dry cloth.
Thermocouple is in wrong position. Adjust the position until the flame is heating it.
Thermocouple is dirty. Clean the thermocouple.
Sparker support is in wrong position. Adjust position of the sparker support.
Abnormal Burner cap is in wrong position. Set the burner in correct position.
Combination The burner is blocked. Clean the burner.
The gas pressure is incorrect. Adjust or change the gas regulator.
The nozzle is blocked. Contact a qualified technician.
Smelling Of Gas The rubber hose is broken. eplace the rubber hose.
ubber hose is not connected properly. Connect the rubber hose in a proper way.
Gas cooker problem. Consult authorized technician.
The burner does not ignite Ignite again after gas is cleared.
Burner Backfire Excessive lint found in the burner emove and clean the burner.
To Injector mixing tube.
Excessive gas pressure. Check gas regulator pressure and adjust if
necessary.
Abnormal Flame Excessive gas pressure. Check gas regulator pressure and adjust if
necessary.
NOTE: please contact the authorized agent or the gas supply authority service agent
immediately for any problem that cannot be rectified.
11
The use of a gas cooking appliance results in the production of heat, moisture and products
of combustion in the room in which it is installed. Ensure that the kitchen is well ventilated
especially when the appliance is in use.
Keep natural ventilation holes open or install a mechanical ventilation device (mechanical
extractor hood). Prolonged intensive use of the appliance may call for additional ventilation,
for example opeining of a window, or more effective ventilation to increasing the level of
mechanical ventilation where present.
CAUTION: “In case of hotplate glass breakage”:
Immediately shut off all burners and any electrical heating element and isolate the appliance
from the power supply, do not touch the appliance surface, do not use the appliance.
DIAMETER OF INJECTS
WOK BURNER SE I-RAPID BURNER
0.86mm (Outer Ring) + 0.40mm (Inner Ring) 0.58mm
ARNING