Mother Choice Orlando 2 in 1 Cot Bed Guide

An IGC Dorel brand
Instruction Manual & User Guide
Orlando 2 in 1 Cot Bed
Please read this manual in its entirety before assembling
the product and follow all instructions contained herein.
Do not use this cot if any part is Broken,Torn or Missing.
Please retain instruction manual for future reference.
Illustrations are representative only.
Design and style may vary.
IMPORTANT: RETAIN FOR FUTURE REFERENCE.

2#13965-7-MC Orlando 2 in 1 Cot Bed 10-12
Instruction Manual & User Guide
page 3
page 4
page 5
page 6
page 7
page 8
page 9
page 10
page 11
page 12
• WARNINGS
• Components list
• Assembly with base in upper posion
• Step 1. Fing hardware to cot end panels
• Step 2. Aaching maress base to cot ends
• Step 3. Aaching side panels
• Step 1. Lowering the maress base
• Step 2. Lowering the maress base (cont)
• Step 1. Converng to a day bed
• Product care and maintenance
• Customer service
Table of Contents
This Instruction Manual applies to the following Model Numbers:
a. #13965 - Orlando 2 in 1 Cot Bed (White).
b. #13966 - Orlando 2 in 1 Cot Bed (Honey).
c. #13967 - Orlando 2 in 1 Cot Bed (Cappuccino).

#13965-7-MC Orlando 2 in 1 Cot Bed 10-12 3
Instruction Manual & User Guide
“IMPORTANT. READ CAREFULLY BEFORE USE AND RETAIN FOR FUTURE REFERENCE.”
RECOMMENDED MATTRESS SIZE.
THIS COT HAS BEEN MANUFACTURED FOR USE WITH A MATTRESS WHICH
MEASURES 690 MM WIDE BY 1300 MM LONG AND 120 MM IN THICKNESS.
THE WIDTH AND LENGTH ARE SPECIFIED BECAUSE IT IS IMPORTANT THAT
THE GAPS BETWEEN THE MATTRESS AND THE SIDES AND ENDS OF THE
COT WILL NOT EXCEED 40 MM.
THIS IS TO MINIMISE THE RISK OF A CHILD’S LIMB BECOMING CAUGHT IN
THE GAP.
THE THICKNESS OF THE MATTRESS HAS BEEN SPECIFIED TO ENSURE THAT THE
DEPTH OF THE COT IS GREATER THAN 500 MM WITH THE MATTRESS BASE IN THE
LOWER POSITION TO MINIMIZE THE RISK OF A CHILD CLIMBING OR
FALLING OUT OF THE COT.
BEFORE ASSEMBLING THIS COT, READ AND UNDERSTAND THE INSTRUCTIONS.
INCORRECT ASSEMBLY MAY MAKE THE COT UNSAFE.
KEEP INSTRUCTIONS FOR FUTURE USE.
 • TO PREVENT FALLS, THE MATTRESS BASE OF THIS COT SHOULD BE
ADJUSTED TO THE LOWEST POSITION BEFORE THE CHILD CAN SIT UP.
 • POSITION THE COT, SO THAT THE CHILD CANNOT REACH CURTAINS, BLINDS
AND POWER POINTS.
 • PLACE THE COT, AT A SAFE DISTANCE FROM OPEN FIRES, BARBEQUES,
HEATERS OR OPEN FLAMES (SUCH AS CANDLES).
 • ENSURE THAT, MEDICATION, STRING, ELASTIC, MOBILES, SMALL TOYS OR
SMALL ITEMS, SUCH AS COINS ARE OUT OF REACH.
 • TO REDUCE THE RISKS OF SUDDEN INFANT DEATH SYNDROME (SIDS),
PAEDIATRICIANS RECOMMEND HEALTHY INFANTS BE PLACED ON THEIR
BACKS TO SLEEP WITH HEADS AND FACE UNCOVERED – UNLESS OTHER
WISE ADVISED BY YOUR PHYSICIAN. - for more details at www.sidsandkids.org
 • Donotplacebumpers,quilts,doonas,duvets,lamb’swoolorsofttoysinthecot.
 • Tucksheetsandblanketsinsecurelysobeddingisnotloose.
 • Whenthemattressbaseisinthelowposition,covertheunusedmattressbase
mounting holes in the end panels with the blanking caps and screws supplied.
 • Latchthedropsideintheraisedpositionwheneverachildisinthecot.
 • Onceachildcanstand,donotleaveanythinginthecotsuchastoysthatprovidea 
foothold to enable the child to climb out.
 • Donottryandmovethecotwhenachildisinit.
 • Thisproductisnotintendedforcommercialuse.
ADDITIONAL WARNING FOR THE FOLLOWING OPTION
1. Cots with castors.
   a. Keepcastorslockedunlessthecotisbeingmoved.

4#13965-7-MC Orlando 2 in 1 Cot Bed 10-12
Instruction Manual & User Guide
TIMBER COMPONENTS REQUIRED FOR COT:
• 2 End panels, 1 Maress base, 2 side panels.
TOOLS REQUIRED:
Allen key (supplied) x 2
HARDWARE:
Blanking bolts 15mm
and caps x 4 each
Allen head bolts
52 mm x 8
(to fasten end panels
to side panels)
Cot with mattress base
in upper position
Day bed
Components List:
Allen head bolts
32 mm x 4
(to fasten end panels
to mattress base)
1 2 3 4
Blanking bolt 15 mm x 4
(to ll side panel holes
in end panels)

#13965-7-MC Orlando 2 in 1 Cot Bed 10-12 5
Instruction Manual & User Guide
ASSEMBLY WITH MATTRESS BASE IN UPPER POSITION
Suits from Newborn until Infant can sit up.
Assembling: Orlando 2 in 1 Cot Bed
It is recomended that two (2) people are needed to safely assemble this product.

6#13965-7-MC Orlando 2 in 1 Cot Bed 10-12
Instruction Manual & User Guide
Assembling: Orlando 2 in 1 Cot Bed (cont)
STEP 1 - FITTING HARDWARE TO COT END PANELS
• Layeachendpanelonacarpetedoor.
• Fit 2 sets of blanking bolts and caps to each end panel, with the
mattress in ther upper positopn, as per Figure 1.
Figure 1
Inside Footboard Inside Headboard
Mattress Base x 1
Tools/Hardware
required:
1
Blanking Bolts x 2 Blanking Bolts x 2
Upper position
suits newborn
Lower position

#13965-7-MC Orlando 2 in 1 Cot Bed 10-12 7
Instruction Manual & User Guide
STEP 2 - ATTACHING MATTRESS BASE TO COT ENDS
• Lay the cot headboard on its side and position the mattress
base, as per Figure 2A.
• Fit one (1) 32mm allen head long bolts (B) through the hole in the cot end
a and into the threaded hole in the mattress base end, as per Figure 2B.
• Repeat for other side.
• Stand the cot headboard on its side and position the mattress base, as per Figure 3A.
• Fit one (1) 32mm allen head long bolts (B) through the hole in the cot end
a and into the threaded hole in the mattress base end, as per Figure 3B.
• Repeat for other side.
• Leaveboltsslightlylooseforeaseofttingsidepanels,asperFigure 4.
Assembling: Orlando 2 in 1 Cot Bed (cont)
Figure 3 B
Tools/Hardware
required:
3
Figure 4
Approx 3mm
Figure 3 A
Figure 2 B
Figure 2 A

8#13965-7-MC Orlando 2 in 1 Cot Bed 10-12
Instruction Manual & User Guide
Assembling: Orlando 2 in 1 Cot Bed (cont)
STEP 3 - ATTACHING SIDE PANELS
• Stand the cot upright.
• Eight (8)52mmallenheadboltsarerequiredfortheassemblyofthe
side panels,as per Figure 5.
• Fit the side panels with rounded edge railing at the top.
• To attach the side panels, use four (4) 52mm allen head bolts and the allen key
supplied, as per Figure 6. Ensure all bolts are tight.
• Repeat for the other side.
• Your newborn cot is now ready to use, as per Figure 7.
Ifitisdifculttotthesidepanelbetweenthecotends,loosenthe
mattress base bolts slightly.
Tools/Hardware
required:
2
Inside Footboard Inside Headboard
Figure 6
Figure 5
Side
Panel
Side
Panel
Side
Panel
Figure 7
52mm
allen head bolt

#13965-7-MC Orlando 2 in 1 Cot Bed 10-12 9
Instruction Manual & User Guide
STEP 1 - LOWERING THE MATTRESS BASE
• Lay the cot its side.
• Removetwo(2) 15mm blanking bolts and caps (A) from the lower
position mattress base mounting holes in each of
the end panels, as per Figure 8.
• Repeat for the other end.
• Loosen the eight (8) 52mm allen head bolts holding
the side panels to the end panels,
as per Figure 9.
• Repeat for the other side.
Assembling: Orlando 2 in 1 Cot Bed (cont)
Tools/Hardware
required:
Figure 9
Approx 3mm
Figure 8
A
A
A

10 #13965-7-MC Orlando 2 in 1 Cot Bed 10-12
Instruction Manual & User Guide
STEP 2 - LOWERING THE MATTRESS BASE (cont)
• Removethefour(4) 32mm allen head bolts (A) securing the mattress
base to each end panel and carefully shift the mattress base (B)
to the lower position, as per Figure 10.
• Retthemattressbaseinthelowerpositionusingthefour(4) 32mm allen head bolts.
• Tighten all bolts, (mattress base and side panels).
• Fit two (2) 15mm blanking bolts and caps (A)
to the upper position mattress base mounting
holes in each of the end panels,
as per Figure 11.
• Stand the cot upright,
as per Figure 12.
• Your cot is now ready to use,
as per Figure 12.
B
AFigure 10
Figure 11
Figure 12
Tools/Hardware
required:
Assembling: Orlando 2 in 1 Cot Bed (cont)
A
A
A