Motoalliance Viper Plow User manual

23001 Industrial Blvd, Rogers, MN 55374 / 1-866-527-7637 / www.motoalliance.com
VIPER PLOW SYSTEM / Honda Rincon
MA11114
Thank you for purchasing the premium VIPER PLOW system. You now have a top-of-the-
line plow system to using for shoving aside snow and dirt with the use of your ATV. Please
note the following instructions and heed all warnings.
WARNING!!!
SEVERE INJURY OR DEATH MAY RESULT IF YOU IGNORE ANY OF
THE FOLLOWING.
−Read the Plow Operator’s Manual, the Winch Operator’s Manual, and all warning labels
before operating.
−Operate ATV at a walking speed with the blade installed. Do Not exceed 5mph (8 km/h)
even with the blade up.
-Plow Cautiously, impact with a hidden or stationary object may cause the ATV to stop
suddenly or go out of control.
--Do Not operate the ATV on slopes greater than 10° with the plow installed.
−Do Not stand or ride on the plow.
Stay clear of moving parts and joints. Keep others away when operating or adjusting plow.
−Inspect the plow mechanism, fasteners, cable, and adjustments before operating. Replace
all worn or damaged parts before operating.
−Lower the plow to the down position before leaving the ATV
unattended.

Parts List
(1) Plow Mount 1
(2) 5/16” dia x 1-1/8” wide U-
bolt
(2) 5/16” dia x 1-3/8” wide U-
bolt
(8) 5/16” dia flat washer
(8) 5/16” dia nylock nut
III. Installation
1. Slide two 5/16” dia x 1-
1/8” wide U
the rear frame cross tubes as shown in figure 1.
2. Place the plow mount under the vehicle, and
slide the legs of the U-
bolts through the four rear
holes in the plow mount. Terminate the U
legs with 5/16” dia flat washers and 5/16” dia
nylock nuts as shown in figure 2.
NOTE: Do not tighten the bolt
and nut
completely. You will do this later in the
installation.
3. Slide two 5/16” dia x 1-
3/8” wide U
the large side frame tubes under the vehicle and
through the plow mount (A1) as shown in figure
3.
bolt
(42012)
bolt
(42018)
1/8” wide U
-bolts over
the rear frame cross tubes as shown in figure 1.
2. Place the plow mount under the vehicle, and
bolts through the four rear
holes in the plow mount. Terminate the U
-bolt
legs with 5/16” dia flat washers and 5/16” dia
and nut
completely. You will do this later in the
3/8” wide U
-bolts over
the large side frame tubes under the vehicle and
through the plow mount (A1) as shown in figure
4. Terminate the ends of the two 5/16” d
3/8” wide U-
bolts with 5/16” dia flat washers
and 5/16” dia nylock nuts as shown in figure
5. Tighten all the 5/16” dia nylock nuts on the
plow mount to a recommended torque of 12
ft-lb (16 N-
m). The completed plow mount
should look like figure 5.
6. If not already done so, assemble the plow per
the instructions that came with the plow blade
kit. Attach the plow to the plow mount using the
clip pins that came with the plow blade.
4. Terminate the ends of the two 5/16” d
ia x 1-
bolts with 5/16” dia flat washers
and 5/16” dia nylock nuts as shown in figure
5. Tighten all the 5/16” dia nylock nuts on the
plow mount to a recommended torque of 12
m). The completed plow mount
6. If not already done so, assemble the plow per
the instructions that came with the plow blade
kit. Attach the plow to the plow mount using the
clip pins that came with the plow blade.

7. If using a winch to lift plow, connect winch
clevis hook to blade and base assembly for easy
connect and disconnect.
WARNING
-Tighten all nuts and bolts securely. Failure
to check all nuts and bolts prior to use can
result in product failure which can lead to
vehicle damage and operator injury or death.
-Take care to not run blade into solid objects.
Doing so can cause blade to crush or bend
front end of your ATV.
FIGURE 1 INSTALL REAR U-BOLTS
FIGURE 2 INSTALL PLOW MOUNT
FIGURE 3 INSTALL FRONT U-BOLTS
FIGURE 4 INSTALL REMAINING FASTENERS
FIGURE 5 COMPLETED PLOW MOUNT