MOUNT PRO PR1008 User manual

If you have any questions , please contact us via: [email protected]
PR1008
V1.0
75x75
100x100
8kg/17.6lbs
32"
Single Monitor Desk Stand
Instruction Manual

If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of
this product, contact Customer Service via [email protected].
Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly specied in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
NOTE: Not all hardware included will be used.
DO NOT EXCEED WEIGHT CAPACITY.
WARNING!
PACKAGE CONTENTS
17.6lbs
(8kg)
B (x1)
Bracket
C (x1)
Base
D (x1)
Pole
G (x3)
Screw
F (x1)
Thumbscrew
H(x1)
4mm Allen Key
I(x1)
6mm Allen Key
E(x1)
Cable Clip
A (x1)
VESA Plate
M-E(x4)
D6 Washer
M-A (x4)
M4x12
M-B (x4)
M4x16
M-C (x4)
M6x12
M-D (x4)
M6x16
01
M-F (x4)
Spacer

Use the 4mm Allen Key (H) to tighten the screws (G) into the pole (D) from the bottom of the base (C).
ASSEMBLY STEPS
STEP 1
02
D
C
G
H

Slide the cable clip (E) onto the pole(D). Slide the mounting bracket (B) onto the pole(D).
Tighten the mounting bracket (B) on the pole(D) using a 6mm Allen Key (I)
STEP 2
03
B
D
E
I

CAUTION:To select the correct bolts(M-A or M-C)
for your monitor, you can try to screw it on your
monitor by hand. The one can screw inside is the
correct bolt for your monitor.
STEP 3
A
A
M-A
M-C
M-E
I
04
M-B
M-D
M-E
M-F
I
OPTION A: Flat Back Monitor
For flat back monitor, secure VESA plate (A) to monitor
using screws (M-A or M-C) and washers (M-E).
OPTION B: Curved Back Monitor
For monitor with curved or recessed back, align spacers (M-F)
with mounting holes in monitor, and secure VESA plate (A) to
monitor using screws (M-B or M-D) and washers (M-E).

Slide monitor with VESA plate onto mounting bracket.
Secure with thumbscrew (F).
STEP 4
05
F

STEP 5
Tighten or loosen tilt joint using 6mm Allen Key (I).
STEP 6
Manage cables with installed cable clip (E).
06
I
E

STEP 7
STEP 8
Store 4mm Allen Key (H) and 6mm Allen Key (I) in cable clip (E).
Adjust monitor position and rotation.
07
Note: When tilted, if the monitor sags or does not stay,
please fasten the tilting bolt on the mount until the
monitor can be held at any angle as needed.
H
I
+45°
-45°
90°
360°
E

Product Dimensions
08
75mm
100mm
114mm
±180°
465mm/18.3"
400mm\15.7"
280mm/11"
90°
38mm
1.5"
50mm
1.96"
-45°
+45°
114mm
100mm
75mm
/2.9”
/3.9“
/4.48“

09

10

CAUTION AND MAINTENANCE:
• Never allow children to climb, stand, hang, or play on any part of monitor or stand.
• This product is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
If you have any questions, please contact us.
[email protected]