Mountup MU0014 User manual

88LBS
40KG
Max:
Max:400x400mm/16x16"
Min:100x100mm/4x4"
26"~55"
(A0)
If you have any questions, please contact us via [e-mail]
MU0014 INSTALLATION INSTRUCTION
- 1 -
Velcro cable ties X5 Bubble level X1

- 2 -
Hammer
3/8"(10mm)
Masonry Drill Bit
7/32"(5.5mm)
Wood Drill Bit
AwlStud Finder
Socket Wrench
1/2"(13mm)
ElectrodrillScrewdriverPencil
3 What is your wall
made of?
Solid concrete
wall?
●This product is designed for use in wood stud or solid concrete wall.
- DO NOT install into drywall alone.
●The wall must be capable of supporting five times the weight of the TV and mount
combined.
●Do not apply this product to any purpose not indicated by MOUNTUP.
●Incorrect installation may result in product damage or body injury. MOUNTUP shall
bear no responsibility for any damage or injury resulted from incorrect installation,
incorrect assembly or misuse.
Please read this instruction carefully before installation.
If you do not understand these instructions or have doubts about the safety of the
installation, assembly or use of this product, contact Customer Service via
[e-mail]
5 Safety Caution
2M2M
Band Tape
Drywall with
wood studs?
CAUTION:
Yes --- Perfect!
No --- This mount is NOT compatible.
MAX:
400mm/16"
MAX:400mm/16"
Yes --- Perfect!
No --- This mount is NOT compatible.
4 Installation Tools
(Not Included)
2Does your TV
(including accessories)
weigh less than
88 LBS (40 KG)?
Before getting started, let’s make sure this mount is perfect for you!
88LBS
40KG
Max:
DO NOT install
into drywall alone
Perfect! Perfect!
Wood Stud Install
Concrete Install
1Is your TV VESA
equal to/greater than
100x100mm/4x4"
andequal to/less than
400x400mm/16x16"?

Arm and Wall Plate
Hardware Included
01 x1 02 x1
Monitor Plate
This product contains
small items that could be a choking hazard if
swallowed. Before starting assembly, verify
all parts are included and undamaged. If
any parts are missing or damaged, do not
return the damaged item to your dealer;
please contact our customer service team.
Never use damaged parts!
NOTE: Not all parts and hardware included
will be used.
WARNING:
Philips Screws
M6 x 15mm
M6 x 30mm
Philips Screws
M4 x 12mm
M4 x 30mm
Washers
Ø6mm
M4-5-6
Spacers
L10mm
x4
x4 x4x4
Philips Screws
M8 x 25mm
M8 x 45mm
x4
x4 x8 x4
Spacers
L5mm
x8
TV Screws / Washers
M-A M-B M-C M-D M-E M-F
Hardware （Wall /Product)
5/16 x 2½ in
Lag Bolts
x3 x1
CA
Washers
Ø8mm
x3
B
Open end wrench
- 3 -
Extenders Nuts Bolts
3B
x2
3A
x2
4A
x8
4B
x8

1. Select TV screw diameter: Thread screws by hand into the threaded holes on the
back of your TV to select which screw diameter fits your TV.
2. Select TV screw length: When attaching brackets to the TV, be careful not to over
tighten screws and be sure that screws do not bottom out in the mounting holes.
Measure and note the width and the height
of the square or rectangle formed from the
VESA holes pattern .
M6M4 M8
Correct Correct
Too Long
Too Short
- 4 -
STEP 1 Select Proper TV Screw
STEP 2 Mesure your TV pattern
W
H
2M2M
100mm ≈4in.
130mm≈5 1/8in.
200mm ≈8in.
300mm ≈11 3/4in
340mm ≈13 3/4in.
400mm≈16in.

- 5 -
STEP 3-1 Select monitor plate configuration
Select the configuration A , B , C, D, or E to use based on the measurement from STEP 2.
for VESA hole pattern:
300x300mm, 400x400mm
for VESA hole pattern:
400x300mm
for VESA hole pattern:
200x300mm, 200x400mm
for VESA hole pattern:
400x200mm, 300x200mm
200 mm
200 mm
400 mm
400 mm
400 mm
400 mm
400 mm
300 mm
300 mm
300 mm
300 mm
300 mm
B
C
DE
for VESA hole pattern:
100x100mm, 130x130mm
200x100mm, 200x200mm.
200 mm
100 mm
130 mm
200 mm
100 mm
130 mm
A
VESA Patter
(WxH) Configuration VESA Pattern (WxH) Configuration
100mm x 100mm A 300mm x 200mm C
130mm x 130mm A 300mm x 300mm E
200mm x 100mm A 400mm x 200mm C
200mm x 200mm A 400mm x 300mm D
200mm x 300mm B 400mm x 400mm E
200mm x 400mm B

- 6 -
STEP 3-2 Assemble monitor plate and extenders
If your TV hole pattern is greater
than 200x200mm, attach
extenders [3A] and [3B] to
monitor plate [02] using Nut [4A]
and Bolt [4B].
4A
4B
3A
3B
3B
02
3A
Socket wrench
C
M-B
M-A
Use the shorter screws
M-B
M-C
M-E
Not for M8 screws
M-B
M-A
Use the longer screws
M-B
M-C
M-E
Not for M8 screws
M-FM-D
STEP 3-3
Attach the Brackets
(a) for Flat Back
(b) for Round Back / Extra space

STEP 4A Wall Plate Installation (Wood stud)
4A-1
4A-2
Locate your studs. Verify and
mark the center of the stud by
finding the stud edges using an
awl, a thin nail, or an
edge-to-edge stud finder.
Position the wall plate at
your desired height and line up
the holes with your stud center
line. Level the wall plate and
make the holes x3.
01
4A-3
Drill pilot holes using a 7/32 in. (5.5 mm)
diameter drill bit.
IMPORTANT: Pilot holes must be
in. (70 mm).
Be sure to drill into the center of thestud.
drilled to a depth of
7/32 in.
Ø5.5 mm
in. (70 mm)
- 7 -
01

4A-4
01 A
Install wall plate using lag bolts
and washers B . Tighten the lag bolts
until they are pulled firmly against the wall
plate .
01
- 8 -
01
Position the wall plate
at your desired height ,
level the wall plate and
mark the polit hole loca-
tions.
Drill pilot
holes
4B-2
4B-1
2.75in 70 mm
Ø 10 mm
Ø 10 mm
STEP 4B Wall Plate Installation (Concrete or Brick)
AB
01
01
AB
UP

Lift and hang TV assembly
onto arm and wall plate.
Secure the monitor plate to the arm
and wall plate with the removed
screws and washers from the
previous step.
- 9 -
A
B
Concrete Wall
Concrete Wall
STEP 5 Lift and hang TV with brackets onto wall bracket.
Contact us by email [email protected] to have
these additional pieces shipped directly to you.
Concrete Wall Anchor
3pcs
Concrete wall anchor (NOT INCLUDED)
01 A
B
01
Install wall plate using lag bolts ,
washers and anchors (not included).
Tighten the lag bolts until they are
pulled firmly against the wall plate .
A
01
Remove 2
preassembled
screws and
washers save
to use.
UP

(Tilting)
Product dimensions:
400mm(15.7”)
400mm(15.7”)
200mm(7.9”)
200mm(7.9”)
100mm(3.9”)
100mm
(3.9”)
171.5
484mm(19”)
+5°/-10°
245mm(9.6”)
69mm
(2.7”)
Loosen the screws Tighten screwsLevel the TV
± 3°
(Leveling)
Loosen the nuts Tighten the nuts
Tilt the TV
+5 /-10°
Tilting angle adjustment (+5° / -10°)
Adjust TV to your desired angle then fasten tilting nuts with open end wrench.
Leveling adjustment (-3°/+3°)
If needed, TV can be leveled ±3 degrees via adjusting the 2 screws with the
open end wrench.
- 10 -
Adjustments
C C
C C