Mountup MU0006 User manual

Triple Monitor Counterbalance Desk Mount
Instruction Manual
If you have any questions , please contact us via: [email protected]
MU0006 75x75
100x100
(1~8kg)x3
(2.2~17.6lbs)x3
27"
V5.0

If you do not understand these instructions or have doubts about the safety of the installation, assembly or use of
this product, contact Customer Service via [email protected].
Before starting assembly, verify all parts are included and undamaged. Improper installation may cause damage or
serious injury. Do not use this product for any purpose that is not explicitly specied in this manual. Do not exceed
weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly or
inappropriate use.
This product contains small items that could be a choking hazard if swallowed. NOT FOR CHILDREN UNDER 3 YEARS.
ADULT SUPERVISION IS REQUIRED.
NOTE: Not all hardware included will be used.
DO NOT EXCEED WEIGHT CAPACITY.
WARNING!
PACKAGE CONTENTS
(2.2~17.6lbs)x3
(1~8kg)x3
A (x1)
Arm
B (x1)
Clamp
All are included in B
Bracket
B1
Clip Plate
B2
Bolts
B5
Bottom Plate
B3
Bolt Y
B4
C (x1)
Decorative cover
G (x1)
Wire clip
K (x1)
Grommet Base
H (x3)
Bolt
I (x3)
Bolt
J (x1)
Support Plate
L(x1)
4mm Allen Key
M(x1)
5mm Allen Key
N(x1)
6mm Allen Key
E(x1)
Middle Head
F(x1)
Pole
D (x3)
VESA Plate
M-E (x12)
D6 Washer
01
M-C (x12)
M6x12 M-F (x12)
M-B (x12)
M4x16
M-D (x12)
M6x16
M-A (x12)
M4x12

Loosen Bolts (B5) by using 6mm Allen Key (N), then lift clip plate (B2), bottom plate (B3), and bolt Y (B4) a little
to release them from bracket (B1).
Attach clip plate(B2), bottom plate(B3), bolt Y(B4), to bracket (B1) using bolts (B5) and 6mm allen key (N).
Mount according to the thickness of desktop.
Mount bracket (B1) to pole(F) using bolts (I). Tighten using 4mm allen key(L).
ASSEMBLY STEPS
STEP 1: Clamp Installation OR Grommet Base Installation
02
35-80mm
NN
10-45mm
F
B1
B5
I
L
B1B1
B3
B4
B3
B4
B5
B5
B2B2
N
OPTION A: Clamp Installation
B4
B
C
N
B1
B2
B3
B4
Decorative cover (C) to pole(F) and secure stand to desktop by tightening clamp (B). Tighten bolt Y (B4) or
by using 6mm allen key (N).
F

OPTION B: Grommet Base Installation
Use 6mm allen key(N) to detach the bolt(B5), clip plate(B2),bottom plate(B3) and bolt Y(B4) from clamp(B).
STEP 1: (Continued)
03
Install the grommet base plate(K) to the pole (F) using bolt (I).
Install pole(F) with bolt Y(B4) and support plate(J). Tighten bolt Y (B4) or by using 6mm allen key (N).
N
B1
B2
B3
B4
B5
B4
K
B4
0-51mm
I
F
J
N

Install the middle head(E), wire clip(G) and swivel arm(A) to the pole.
Fasten the bolt with supplied 6mm Allen key (N)
STEP 2 : Arm Installation
04
N
G
E
A

NOTE: Hand tighten screws to avoid over tightening.
STEP 3 : Attach Monitor
05
M-A
M-C
M-E
N
M-B
M-D
M-E
M-F
N
OPTION B: Curved Back Monitor
Attach the VESA plate (D) to back of monitor and secure
with screws (M-B) or (M-D) with washers (M-E)and
washers(M-F)using 6 mm Allen Key (N). Avoid excessive
tightening screws damage the monitor.
OPTION A: Flat Back Monitor
Attach the VESA plate (D) to back of monitor and
secure with screws(M-A)or(M-C) with washers(M-E)
using 6 mm Allen Key (N). Avoid excessive
tightening screws damage the monitor.
D
D

Slide the monitors onto the head of swivel arm.Install the security bolt (H). Make sure the security bolt is
installed before you rotate the monitor.
STEP 4 : Hang Monitor
06
H
Refer to below illustrations to
adjust tilting angle of your monitor.
Note: Fasten/loosen the tilting bolt
as needed per arrow direction (+/-)
shown in above diagram.
N

Note：
Be sure to keep the arm in
horizontal position during
adjustment. Or else it would
be dicult to adjust the
mount or damage the mount.
STEP 5 : Adjust Tension
For proper functioning of this mount, depending on dierent weight of monitor you might need to adjust
tension in gas spring arm (A) using 6 mm Allen Key (N).
07
N
N
CAUTION
A
M
Clockwise ("-" direction) reduces tension,
counter clockwise("+" direction) increase
tension. The tension should be just enough
to hold your monitor in place without lifting
itself up.
Note: When tilted, if the monitor sags or
does not stay, please fasten the tilting bolt
on the mount until the monitor can be held
at any angle as needed
Refer to above illustrations to adjust
the level of tightness of the arms.
+
-
M
If necessary, refer to above illustrations
to adjust the level of tightness of the
arms.

STEP 6 : Cable Management
Remove bottom plastic covers from gas spring arm (A) .Run cables from monitor through bottom of
gas spring arm (A). Reattach plastic covers as shown in diagram.
08
A

Adjust as Desired
09
±180°
±90° ±90°
+35°
-35°
M
N
DESK DESK
Pay attention while clamp install !
Note: The total length of 3 monitors after
arrayed can not be longer than 183cm.
≤183cm

10
Product Dimensions
2.9”
3.9“
4.48“
2.9”
3.9“
4.48“
8.1“-10.3”
6.3“
6.3“
1.7”
2.67”
145mm/5.7" 16.5”
0"-3.14"
+35°
-35°
±180°
±180°
±180°
±90°
±90°
4.5“-27.8“
11.5”
0"-2.95"

STEP 6
CAUTION AND MAINTENANCE:
• Never allow children to climb, stand, hang, or play on any part of monitor or stand.
• This product is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
• Check that the bracket is secure and safe to use at regular intervals (at least every three months).
If you have any questions, please contact us.
[email protected]