Mountup MU7012 User manual

75 x 75 mm
100x100mm
(6.6 ~ 33 lbs) x 2
(3~15kg) x 2
Premium Dual Monitor StandInstruction ManualIf you have any questions, please feel free to contact Customer Service via Amazon before returning.US1.0

1Arm Set（x2） 2Base（x1） 3 Vesa Plate（x2） 4 Plate（x1）
5M8x150
Screw Bolt（x1）
65mm
Allen Key（x1）
3mm
Allen Key（x1）
7
A(x8)
M4x12
B(x8)
M4x16
C(x8)
M5x12
D(x8)
M5x16
TOOLS
VESA
SCREWS
PACKAGE CONTENTS
BEFORE ASSEMBLY
WARNING
Layout all components and hardware. Check all parts are included and undamaged.
Should anybody intends to install or use this monitor arm, please read and understand this manual carefully.
This product contains small items that could be a choking hazard if swallowed.
KEEP AWAY FROM CHILDREN UNDER 3 YEARS OLD. ADULT SUPERVISION IS REQUIRED.
Improper installation, such as using the product for monitors over its load capacity or for any purpose not
explicitly specified, may cause damage or serious injury. We would not be liable for any damage or injury caused
by improper mounting or inappropriate use.
If you do not understand these instructions or have any doubt about the safety instructions, assembly or use of
this product, please contact our customer service.
SAFETY INSTRUCTIONS
E(x8)
D5 Washer
F(x8)
D5 Plastic Spacer
Part List

01
STEP 1: Mounting the Base6
6
2
OPTION A: Clamp InstallationAdjust the Clamp width to fit with desk. ASSEMBLY STEPS
Secure stand to desktop by tightening Clamp with Allen key (6).Table thickness:0.4''~1.97''10~50mm

02STEP 1: Mounting the BaseEnsure the desktop has a hole between 0.4'' and 2.4'' in diameter to use this option. Using a grommet hole that is already in your desktop is acceptable.DESK DESK
ø 10~60mm
ø 0.4~2.4"
6
6
OPTION B: Grommet Installation 6
2
4
5
0.4''~3.15''10~80mm+
Remove the short bolt for clamp installation from part 2.Insert the long bolt (5) through the plate (4) and the hole on the table top, and then use the Allen key (6) to tighten.

03STEP 2: Arm InstallationInsert the arm into the base and adjust the screw with the Allen key (7) to fix the lower arm.1
1
7
The screw are used to adjust the tightness of the connection between the base and the bracket arm to avoid the arms from shaking.Turn the head to the straight by hand before assembling the arm.

04STEP 3 : Attach Monitor/ Recessed Back Monitor
OPTION B: Curved
Do not tighten the screws excessively or your monitor might be damaged.OPTION A: Flat Back Monitor
Attach the VESA plate (3) to the back of monitor
and secure it by using a 5mm Allen Key (6) to
tighten screws along with washers.
Do not tighten the screws excessively
or your monitor might be damaged.
Monitor Monitor Monitor
No!
monitor monitormonitor
No!
3
6
Spacers F3
6
Screws and WashersScrews and WashersAttach the VESA plate (3) to the back of monitor and secure it by using a 5mm Allen Key (6) to tighten screws along with washers and spacers.

105STEP 4: Hang Monitor and Adjust Monitor Tilting Angle Slide the monitors onto the head of arm.
6
Turn clockwise to tighten
Turn counterclockwise to loose
+
-
6
If the tilt adjustment mechanism is too tight or too loose, please adjust the screw as showed below.Important Notice:
The pressure of the gas spring is
initially set to an intermediate
value. So when the monitor hangs,
make sure to hold it with both
hands and don't let it drop
suddenly. 1PUSH2REMOVE
Note:If you want to remove the monitor, push the lock plate front and lift the monitor to separate the monitor from the arm.

06STEP 5: Adjust Gas Spring Tension For proper functioning of this mount, depending on different weight of monitor you might
need to adjust tension in upper arm (1) .
Situation 1: Arm falls down
Upper Arm with monitor falls down and fails to stay where intended.
Solution:
Turn the inside screw counter-clockwise (“+”direction) to increase gas spring tension until the arm can stay as intended.Solution:
Turn the inside screw clockwise (“-”direction) to decrease gas spring tension until the arm can stay as intended.Situation 2: Arm rises up / can't be pressed down
Upper Arm with monitor rises up automatically or can't be pressed down and fails to stay
where intended.
6
6

07STEP 6: Cable ManagementRemove Cable Cover
Remove two keys first, then remove the cover.Attach Cable Cover
Insert the cover first, then install the two keys.

08Adjust as Desired
Tilt
Swivel
Rotation
Height
DESK DESK
Adjust monitor position and rotation.
Note: To ensure stability, the tightness of the rotating axis has
been preseted, so it would be kind of difficult to rotate the
VESA plate.
Suggestion: Please attach the monitor first, then hold the two
sides of it with both hands, and rotate vigorously. If that
doesn't work out, please do not hesitate to ask for our help.
WARNING:
For your safety, do not move the stand off your
desk!
+90°
-45°
±180°

CAUTION AND MAINTENANCE:
• Never allow children to climb, stand, hang, or play on any part of monitor or stand.
• This product is intended for indoor use only. Using this product outdoors could lead to
product failure and personal injury.
• Check that the bracket is secure and safe to use at regular intervals
(at least every three months). 09Product Dimensions
0.4''~3.15''
2.76''8.19''±9 0°±180°±180°min9.88''~max12.44''±90°2.95''±90°2.95''4.53''3.94''
2.95''3.94''4.53''
min0.4''~max1.97''
min6.1''~max 19.69''