Multibrackets M Motorized Turn Mount User manual

M Motorized Turn Mount
7
10
Buttons function instructions
Stop button
OK
Out button. Press and release . The TV wall mount will fully unfold.
In button. Press and release . The TV wall mount will automatically return to rest against the wall.
The left button. Press and release , the TV wall mount will swivel to the left until is pressed or the
TV wall mount swing to -30 degrees to stop.(Note󰦗
.󰦆
OK
Memory button1.Press and hold for 5 seconds, the buzzer will sound twice beep beep, LED light will turn
on for 1second, The memory is saved as location 1.
Memory button2.Press and hold for 5 seconds, the buzzer will sound twice beep beep, LED light turn on
for 1second, The memory is saved as location 2.
+Learning button, Please read the instructions below for more info.
+To recall the button(location 1). Press and release button, and then press button,
The TV wall mount will automatically swivel to the location1 after the buzzer sounds once.
+To recall the button(location 2). Press and release button, and then press button,
The TV wall mount will automatically swivel to the location2 after the buzzer sounds once.
The right button. Press and release , the TV wall mount will swivel to the right until is pressed or
the TV wall mount swing to 30 degrees to stop.(Note󰦗
.󰦆
Learn mode operation instructions
The loss of matched remote control would result in TV wall mount being unusable. The LEARN MODE is used
to learn how to use TV remote (ONLY suitable for the TV remote of popular brands.) to control TV wall mount.
Note:
TV remote can’t replace the all functions of matched remote control. Only LEARNING the five buttons functions.
With , , , and respectively.
The user must follow the rules below when using the TV remote to control TV wall mount.
Select the alternate buttons from the TV remote, and the button that can't direct control the TV .
OK
.
OK
Press and hold for 5 seconds until LED light on the matched remote control stays on, and then
press . The buzzer will sound once, the red LED light on the IR receiver will stay on, then the
LEARN MODE will be entered.
STEP1:
LEARN MODE instructions as shown below:
Note: When there is no activity for over 20 seconds in any step .TV remote will automatically exit from the
LEARN MODE.
STEP2: If LEARN , please press on the matched remote control until the buzzer sounds twice,
the red LED light on the IR receiver will change from being steady to a slow flash.
STEP3: Aim the TV remote at the IR receiver, and press the button on the TV remote that you need to set as
the function of button until the buzzer sounds three times. the red LED light on the IR receiver will
change from slow flash to a fast flash.
OK
STEP4: Press button on the matched remote control until the buzzer sounds four times. The red LED light
on the IR receiver will turn off. Button will be LEARNED successfully. If the buzzer only
sounds once, then a LEARN failure.(The TV remote won’t support the LEARNING function).
Learn “Power” button on the TV remote:
Press and hold for 5 seconds until LED light on the matched remote control stays on , and then press
The buzzer will sound once, the red LED light on the IR receiver will stay on, then press and hold button
on the matched remote control until the buzzer sounds twice, then release the button. The red LED
light on the IR receiver will change from being steady to a slow flash.
Aim the TV remote at the IR receiver, and press “Power” button. The buzzer will sound three times. The red
LED light on the IR receiver will change from slow flash to a fast flash. Press button on the matched
remote control until the buzzer sounds four times. The red LED light on the IR receiver will turn off. “Power”
button will be LEARNED successfully. If press “power” button, the TV wall mount will automatically reset.
OK
OK
(Please follow step1 through step4 in turn if the user need to LEARN more buttons)

TV
!
TV
21
1
2
ab
ST6.3x55 (x4)
W-A concrete anchor (x4)
W-B
D6 washer (x2)
W-C
G (x8)
motorized wall mount (x1)
A
decorative
cover (x2)
B
remote
control (x1)
C
adapter (x1)
D
VESA
adaptor (x2)
E
VESA
adaptor (x2)
F
D8
washer (x4)
M-G
D6
washer (x4)
M-F
M5x14 (x4)
M-A
M6x14 (x4)
M-B
M8x20 (x4)
M-C
big
spacer (x4)
M-I
M6x30 (x4)
M-D
M8x30 (x4)
M-E
small
spacer (x8)
M-H
75/100/200x100/200x200 300/400

X
W-A
10mm
big hole
big hole
W-A
W-C
4
3
4b
3
3a 3b
3b-1 3b-2 3b-3
X
X

W-A
W-B
10mm
W-C W-A
X
X

4a
G
5
6
180°

M-A
M-B
M-C
M-F
M-G
Top of the TV
9
M-F
M-G
M-C
M-D
M-E
M-H
M-H
M-F
M-G
M-D
M-E
M-I
M-C
M-G
M-H
M-D
M-E
M-I
M-H
M-F
M-G
or or or
56
7b
8
±30°
90°
Do not open the electrical
cover.
10
Remote control operation instructions
remote contr ol
STEP 3: Follo w the Ke y function instru ctio ns below to ope rate .
Note: f TV wal l moun t encounters an obs tacl e or has some
damage of mach iner y part in the process , TV wa ll mount will
stop automatical ly and s ound three ti mes be ep beep beep.
hen the wall mo unt me ets with an obstacl e in the p rocess.
Please remov e the ob stac le and push the w all mo unt by
hand until ret urns i t flat against the wa ll. The wall mount can
normal use aft er pre ss but ton.
When powered , the buzzer sounds o nce be ep, TV wall
mount will be in s tand by state.
STEP 1:
Press to return th e TV wa ll mount flat again st the
wall and h ear on e beep from the buzze r, the sy stem will
then enter a wor king c ondition.
STEP 2: OK
11
7a