Multibrackets M Universal Projector Ceiling Mount 900-1600 with Fine... User manual

AB
A
B
A
A
B
A
B
A
B
●Be sure to read this manual thoroughly and to do the installation work safely.
Keep this manual available for future reference.
●Sufficient expertise is required for installing this projector Ceiling mount.
●Do not use the projector Ceiling mount for purposes other than for which it is designed.
To Adjust The Upward/Downward Slide
To Install The Projector On The Projector MountCeiling
To Adjust The Vertical Tilt
Product Information:
Locking screws
Adjustment buttons Adjustment direction
Adjustment direction
Connect the power cable and
other cablesto the projector.
Adjustment direction
Adjustment direction
B
To Adjust The Horizontal Rotation
To Adjust The Horizontal Roll
AB
Adjustment buttons
A
B
Adjustment buttons
AB
A
B
Adjust the leftward/
-rightward slide
Adjustment direction
● Move the projector mounting plate and adjust the leftward/rightward slide.
A
B
AB
M Universal Projector Ceiling Mount
900-1600 with Fine tune
To Remove The Projector Ceiling Mount
stick
● Use a stick or something hard to pry open the ceiling plate cover.
www.multibrackets.com www.multibrackets.com
Adjustable Range
Adjustable Angle ± 5° tilt, left\right, front\rear and lateral rotation adjustment
Model M Universal Projector Ceiling Mount 900-1600 with Fine tune
900mm-1600mm(from mounting plate bottom to the ceiling)
Product Weight 2.6kg
Max Weight Load 25kg
41L1620-EN-MB
A
C

D、E
Checking The Supplied Accessories
Important Safety
To Set The Projector Mount On The WallCeiling
To Set The Projector Mount On The WallCeiling
To Install The Projector On The Projector MountCeiling
Projector
mounting plate
Extend arms
Extra screws and anchor bolt are backup!
K
4
3
Be sure to read this manual thoroughly to do the installation work.
Only qualified service personnel (two or more) should carry out installation or dismounting of the projector
from the projector wall mount.
For safety reasons, check the strength of the wall before installation. If the wall is not strong
enough, reinforce it sufficiently before installation.
Do not make alterations to the projector mount.Ceiling
Use the supplied accessories only. Use of accessories other than those supplied may result in damage to
the projector mount.Ceiling
Do not hit or hang any heavy objects on the projector mount. If the projector mount is Ceiling Ceiling
damaged, stop use and contact a qualified service person immediately.
When dismounting the projector from the projector mount, be sure to unplug the AC power cord andCeiling
other connecting cables beforehand.
9
8
7
To avoid fire, do not install the projector with the projector mount in a humid or excessively dusty place.Ceiling
Please install this apparatus only on the horizontal surface instead of the slanting one.
5Do not install the projector mount on a wall subject to vibration or impact.Ceiling
2
* Manufacturer is not liable for any damages or injury caused by mishandling or improper installation.
Use with products heavier than the maximum weights(Weight Capacity： ＜25kg) indicated may
result in instability causing possible injury.
I
F
F
J
H
D、E、F
K
a.Use the extend arms :
b.Do not use the extend arms :
or
Do Not use
Connecting
Use
screws K
Connecting
screws
Connecting
screws K
10
10
10
12
Screw from
Parts List
Do Not use
Connecting
Use
screws K
Connecting
screws
Connecting
screws K
10
10
10
Screw from
Parts List
or
To Set The Projector Mount On The WallCeiling
>55mm
ø3mm
>55mm
ø10~11mm
B
Concrete mountingCeiling
Use anchor bolt
Dry- mountingCeiling
Not use anchor bolt
● Concrete ceiling mounting thickness must be
a minimum 100mm. Anchor bolt and sсrew
(M6 × 55) are needed to be used for installation.
● Dry-ceiling mounting thickness must be a minimum
70mm. Only sсrew(M6 × 55) is needed to be used
for installation. If the wall is not strong enough,
reinforce it sufficiently before installation.
● Please contact reseller if you have
any questions about mounting surface issue.
www.multibrackets.com www.multibrackets.com
18°
The angle of the ceiling wall is not more than 18°
A
C
To thread the power
cable and other cables
from the AL pipe
Center Line
Wooden Stud
CAUTION:
Make sure both mounting
holes are on center line of
the stud.
60mm
Loose the screws and remove
the projector mounting plate
Loose the screws
G
B
NO
C
D
E
A
5
5
1
4
4
F
4
Screw(M6X55 )
Φ10mm Anchor bolt
Allen key
Screw(M3X10 )
G
Screw(M5X12 )
M5 nuts
spacer(8.0)
4
H
I
4
4
Screw(M4X10 )
Screw(M5X25 )
M6 Connecting screws
J
4
diagrammatic
presentation
designation
quantity
NO
diagrammatic
presentation
designation
quantity
AL arm (1)Projector mount (1)
Ceiling plate with cover (1) K
4
Screw(M5X15 )