Mytee Hp100 grand prix User manual

13655 Stowe Dr., Poway, CA. 92064

Instructions for

HP100 Grand Prix™

Please read before use.

at www.mytee.com/help

Set up p. 3

General information p. 6

Parts & pricing p. 9

Wiring diagram p. 11

Notes p.12

Model #

Serial #

Form # ADM-HP100

7-11

HP100 GRANDPRIX™ BACK

ACCESSORIES

HP100 GRANDPRIX™ FRONT

1. Waist high controls

2. 2” Male Cuff-Lynx™

3. Solution tank lid

4. Female quick disconnect

5. Blower attachment

6. Solution tank

7. Push handle

8. Easy open lid

9. Bucket-high drain valve

10. Single 25’ power cord

11. Vent guard

12. Quality 8” wheels and 3” locking casters

13. Motor base housing

8400- 3” Stainless Steel H122 - Cuff-Lynx™

Upholstery Tool 1 / 1/4” reducer

8501- 15’ 1-1/4” Vac/Sol Hose H375- Hose Hanger

(4) screws

H226 Drain Elbow

HP100 GRAND PRIX™

REPLACING HOSE CUFFS WITH CUFF-LYNX™

Now that you have your GrandPrix™, you will need to replace

the cuffs on your vacuum hose. To remove old cuffs, twist clock-

wise. To attach reducer Cuff-lynx™ to vacuum hose twist counter

clock-wise.

Twist clock-wise to remove standard cuffs.

Twist counter clock-wise to attach Cuff-Lynx™ to vac. hose.

HP100 GRAND PRIX™ PUMP

After the machine has been plugged into a 20 amp grounded

outlet, turn on pump. Key tool until upholstery tool releases a

steady ow.

HP100 GRAND PRIX™ HEATER

Release tool trigger. Turn on heater. Wait 8 – 10 minutes for unit

to pre-heat. Once heated, re-key upholstery tool until hot water

begins owing. Once hot water is owing, release trigger and

pre-heat an additional 4 – 5 minutes.

HP100 GRAND PRIX™

HP100 GRAND PRIX™ FILL SOLUTION TANK

Lift lid to ll. For best results, ll with warm water (140o F).

HP100 GRAND PRIX™ VAC/SOL

HOSE CONNECTIONS

Attach one end of a solution hose to a wand or other tool, the

other end to the Grand Prix™ front quick disconnect. Attach one

end of a vacuum hose to the tool, the other end to the Grand Prix™

Cuff-Lynx™ vacuum hose port.

VACUUM PUMP HEATER

HP100 GRAND PRIX™ 45 DEGREE SPOUT DRAINHP100 GRAND PRIX™ RECOVERY TANK

When the oat shuts off vacuum, empty tank. Pull lever located at

the back of the machine to release water.

Add a defoamer in the recovery tank to reduce foam, prolonging

the life of the Grand Prix™ vacuum motor .

HP100 GRAND PRIX™

HP100 GRAND PRIX™ VACUUM MOTOR

Turn on vacuum motor and begin cleaning. For best results

make two dry passes to every wet pass.

HP100 GRAND PRIX™ BLOWER ATTACHMENT

Connect blower attachment for drying (optional).

VACUUM PUMP HEATER

Dear Customer:

Congratulations on the purchase of your new HP100 Grand Prix™. As you are

already aware, the scene of the equipment world is becoming more high tech, and

we at Mytee Products Inc. strive to keep you on the cutting edge with superior

quality and technology.

Keep in mind that the HP100 Grand Prix™ is a machine, so neglect or abuse

will cause unnecessary damage and void the warranty. However with simple

maintenance the HP100 will give quality performance for many years to come.

If warranty questions arise, please consult your user manual or get in touch with

your distributor. If you have questions about maintenance, replacing parts or

ordering parts, please call an authorized Mytee Products Inc. Service Center.

To see an updated list, visit our website at www.mytee.com

Before you begin cleaning, please read your manual thoroughly.

Sincerely,

Mytee Customer Care Dept.

Grounding Instructions

This machine must be grounded. If it should malfunction or breakdown, grounding

provides a path of least resistance for electrical shock. This machine is equipped

with a cord having an equipment-grounding conductor and grounding plug. The plug

must be plugged into an appropriate outlet that is properly installed in accordance

with all local code and ordinances. Do not remove ground pin; if missing, replace

plug before use.

Improper connection of the equipment-grounding conductor can result in a risk of

electric shock. Check with a qualied electrician or service person if you are in doubt

as to whether the outlet is properly grounded. Do not modify the plug provided with

the machine. If it will not t the outlet, have a proper outlet installed by a qualied

electrician.

This appliance is for use on a nominal 120-volt circuit, and has a grounding plug

that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated

in Figures 2 and 3 may be used~to connect this plug to a 2-pole receptacle as

shown in Figure 2 if a properly grounded outlet is not available. The temporary

adapter should be used only until a properly grounded outlet (Figure 1) can be

installed by a qualied electrician. The green colored rigid ear, tab or the like

extending from the adapter must be connected to a permanent ground such as a

properly grounded outlet box cover. Whenever the adapter is used, it must be held

in place by a metal screw. Grounding adapters are not approved for use in Canada.

Replace the plug if the grounding pin is damaged or broken.

The Green (or GreenYellow) wire in the cord is the grounding wire. When replacing

a plug, this wire must be attached to the grounding pin only.

DO NOT use extension cords.

Please Note for America use only

Parts and Service

Repairs, when required, should be performed by Mytee service personnel or Mytee

authorized Service Center using Mytee original replacement parts and accessories.

Call Mytee for repair parts or service. Please specify the Model and Serial Number

when discussing your machine.

Name Plate

The Model and Serial Number of your machine are shown on the Nameplate on the

back panel of the machine. This information is needed when ordering repair parts

for the machine. Use the space provided on the front cover to note the Model and

Serial Number of your machine for future reference.

Unpacking the Machine

When the machine is delivered, carefully inspect the shipping carton and the

machine for damage. If damage is evident, save the shipping carton so that it can

be inspected by the carrier that delivered it. Contact the carrier immediately to le a

freight damage claim.

Caution and Warnings

Symbols

Mytee uses the symbols below to signal potentially dangerous conditions. Always

read this information carefully and take the necessary steps to protect personnel

and property.

Is used to warn of immediate hazards that will cause severe personal injury or death.

Is used to call attention to a situation that could cause severe personal injury.

Is used to call attention to a situation that could cause minor personal injury or

damage to the machine or other property. When using an electrical appliance, basic

precautions should always be followed, including the following: Read all instructions

before using this machine. This product is intended for commercial use only.

To reduce the risk of re, electrical shock, or injury:

1. Read all instructions before using equipment.

2. Use only as described in this manual. Use only manufacturer’s recommended

attachments.

3. Always unplug power cord from electrical outlet before attempting any adjustments

or repairs.

4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.

5. Do not pull or carry by cord. Do not close a door on cord or pull cord around sharp

edges or corners.

6. Do not run appliance over cord. Keep cord away from heated surfaces.

7. Do not use with damaged cord or plug. If cord is damaged, repair immediately.

8. Do not use outdoors or on wet surfaces and or standing water.

9. Always unplug or disconnect the appliance from power supply when not in use.

10. Do not allow to be used as a toy. Close attention is necessary when used by or

near children.

11. Do not use in areas where ammable or combustible material may be present.

12. Do not leave the unit exposed to harsh weather elements. Temperatures below

freezing may damage components and void warranty.

13. Use only the appropriate handles to move and lift unit. Do not use any other parts

of this machine for this purpose.

14. Keep hair, loose clothing, ngers, and all parts of the body away from all

openings and moving parts.

15. Use extra care when cleaning on stairs.

16. To reduce the risk of re or electric shock, do not use this machine with a solid-

state speed control device.

17. The voltage and frequency indicated on the name plate must correspond to the

wall receptacle supply voltage.

18. When cleaning and servicing the machine, local or national regulations may

apply to the safe disposal of liquids which may contain: chemicals, grease, oil, acid,

alkalines, or other dangerous liquids.

19. Do not leave operating unattended.

Filling the Solution Tank

1. Fill the solution tank with the approved cleaning solution.

2. Do not ll up the solution tank completely: 1” should be left free at the top.

3. Typically, the solution should be a mixture of water and a cleaning chemical

appropriate for the type of job.

4. Always follow the dilution instructions on the chemical container label.

5. The temperature of the cleaning solution must not exceed 70oC/160oF.

Use only non-ammable liquid in this machine.

Figure 1

Grounding Pin

Grounded Outlet

Grounded Outlet Box

Adapter

Tab for Grounding

Screw

Metal

Screw

Figure 2 Figure 3

GENERAL INFORMATION

Setup

1. Open lid of solution tank. Fill solution with water or approved cleaning agent. For

best results, ll with warm water (140o).

Flammable materials can cause an explosion or re. Do not use ammable solutions

or materials in tank(s).

FOR SAFETY: When using machine, follow mixing and handling instructions on

chemical containers.

ATTENTION: If using powdered cleaning chemicals, mix prior to adding.

2. Attach solution hose (located front of machine). NOTE: Make sure the quick

disconnect snap together rmly. As you do this, always inspect hoses for cracks or

fraying. Do not use if hoses are damaged.

3. Attach other end of solution hose to wand.

4. Attach vacuum hose to recovery tank.

5. Plug machine’s cord into a grounded wall outlet. FOR SAFETY: Do not operate

machine unless cord is properly grounded. FOR SAFETY: Do not operate machine

with the use of an extension cord.

6. Turn on pump. Key tool until you have a steady ow.

7. Release tool trigger. Turn on heater.

8. Wait 8–10 minutes for unit to pre-heat.

9. Re-key upholstery tool until hot water begins owing.

10. Once hot water is owing, release trigger and pre-heat an additional 4–5 minutes.

11. Turn on vacuum motor.

12. Begin cleaning. Make two dry passes to every wet pass.

13. For oor cleaning, unplug tool and attach oor wand.

14. Work away from cords to avoid damage.

15. Use a defoamer in your recovery tank.

16. To clean heavily soiled areas, repeat cleaning from different directions.

17. When oat shuts off vacuum, empty tanks.

18. When work is complete, unplug cords and hoses.

19. Wrap and clean hoses. Clean all tanks.

Pre-Operation

1. Vacuum carpet and upholstery and remove other debris.

2. Perform machine setup procedures.

3. Inspect power cord for damage.

Operation

1. Turn pump switch on.

2. Pull up on tool lever to release air in the line. Hold lever until a steady ow of water

comes out of the wand.

3. Once pump is primed and there is pressure in the solution line, turn on heater switch

(if model is equipped with heater) and wait a few minutes for water to heat up.

4. Once water is heated, turn on vacuum and begin cleaning.

Note: When cleaning upholstery, always check manufacturer’s cleaning instructions.

1. Work away from outlet and power cord to prevent cord damage.

2. Use a recommended foam control solution in the recovery tank to prevent vacuum

motor damage. Periodically check for excessive foam buildup in solution tank, and

recovery tank.

3. To clean heavily soiled areas, repeat cleaning path from different direction.

4. When ball oat shuts off vacuum, it is time to empty the dirty water from the

recovery tank, and rell solution tank.

5. After cleaning, relieve water pressure from tool before disconnecting hose.

Squeeze trigger for ve seconds after turning main power switch off.

After Use

1. Unplug.

2. Empty solution tank and rinse it with clean water.

3. Inspect hoses and replace if damaged.

4. Inspect solution lter. Clean or replace if damaged.

5. Store the machine in a clean, dry place.

6. Open recovery tank cover to promote air circulation.

Maintenance Schedule

Maintenance item Daily Once a week

Clean and inspect Tanks

Clean and inspect Hoses

Check lters

Check power supply cable

Clean machine with all purpose cleaner and cloth

Check spray nozzles

Flush solution system with Mytee system maintainer

Remove and clean oat shut-off screen from tank

Inspect vacuum hoses for holes and loose cuffs

Trouble Shooting

There is no power.

1. Plug machine in proper outlet.

2. Check circuit breaker; reset circuit breaker, other items should not run on the

same circuit as machine. Outlet must be a 20-amp circuit.

Pump does not work properly.

1. Snap quick disconnects rmly together.

2. Check solution tank; may be empty.

3. Jets clogged, remove jet and ush clean.

4. Filters clogged, remove lters and rinse clean with water.

5. Heater is blocked; ush out with Mytee’s system maintainer.

6. If brass check valve is stuck replace valve.

7. Check pump wire. May need to reconnect wire.

8. Switch plate switch may need to be replaced.

9. If pump motor brushes are worn, replace pump.

Heater does not work properly.

1. If sensor mounted on the heater has popped, reset sensor by pushing in button.

2. Heating element may need to be replaced.

Vacuum motor does not work properly.

1. Check that hose is tightly connected.

2. Close drain hose valve completely.

3. Secure the vacuum tank tightly.

4. If ball oat is shut off, empty vacuum tank of all wastewater.

5. Make sure ball oat is rmly installed on the elbow.

6. If water is coming out of vacuum motor, use a low foaming detergent.

7. Clean upholstery tool or oor wand jets.

Accessories (optional)

2200H Airmover

3601 System Maintainer

2700 Mytee-Dry

8390 Wand

8700 Crevice Tool

3000 Tradewind™

HP-Dry Vehicle Drying Kit

FAQs

Q: How much does the HP100 weigh and what are the shipping dimensions?

A: 85 Pounds - Box dimensions are 29” x 18” x 36”. Must ship motor freight.

Q: What comes standard with the HP100?

A: The HP100 comes with a hose hanger ( H375 ), four screws, a 25’ 12/3 Cord, 15’

1-1/4” Vacuum/Solution Hose ( 8501 ), a 3” Stainless Steel Upholstery Tool ( 8400 ),

and a Cuff-Lynx™ reducer ( H122 ).

Q: Does Mytee recommend a tool for the machine?

A: A variety of tools can be used with the unit, including our 8390 wand, 8700 crevice

tool, and 8400 upholstery tool. Also our HP-Dry kit can be used for drying interiors

and exteriors.

Q: Where do I plug the machine in?

A: The HP100 requires a 20A grounded circuit. Please note: GFI outlets may trip

before the breaker setting.

Q: What is the proper pre heat cycle for the HP100?

A: Turn pump switch to the on position and prime pump through the solution hose

and the tool. Then turn the heater switch to the on position. Let the machine sit idle

for 8-10 minutes. Spray tool until you feel the hot water from the jet. Let machine sit

idle for an additional 3-5 minutes. This will insure the water in the heater and hoses

will be at the hottest point to start cleaning.

GENERAL INFORMATION

Q: Are the pumps re-buildable for the HP100?

A: Yes, both the seals and the pistons have repair kits available.

Please see the pump manual that shipped with your machine for the

maintenance schedule.

Q: Is there anything I can do to increase the expected life of my machine?

A: Running the vacuum motors with the tank empty and lid off will allow excess

moisture in the vacs to dry off. You should also run a System Maintainer through

the system to keep the hoses, pump, and heater clean and free of debris.

Warranty

MYTEE LIFETIME LIMITED WARRANTY POLICY

Mytee Products, Inc. endeavors to provide high quality products and product support

to its customers and therefore backs up all of its new products purchased from Mytee

Products Inc. (“Mytee”) or any authorized Mytee distributor/service center with this

lifetime limited warranty. This limited warranty begins on the date of the customer’s

purchase and is valid and available to the original purchaser with proof of purchase,

and is not transferable. Mytee’s products are for commercial use only and are not

intended for personal, family or household uses.

HOUSING LIMITED LIFETIME WARRANTY: Mytee warrants for life that its rotation-

ally-molded housings will be free from manufacturing defects. This warranty covers

the cost of replacement or repair only and does not cover shipping or labor costs.

WEAR PARTS 90-DAY LIMITED WARRANTY: Mytee will replace all wear parts for

90 days from the date of original purchase. “Wear parts” are items which wear out

as a result of usage or the passage of time and are consumed despite attempts to

maintain them, such as gaskets, wheels, brass, cords, wires, electrical terminals,

hoses, switches, thermostats, plastisol parts, lters, bearings, brushes, solenoids, o-

rings, bulbs, heating elements, castors, or other parts deemed wear items in Mytee’s

sole discretion. This warranty covers the cost of replacement only and does not cover

shipping or labor costs.

PUMP, VACUUM MOTOR AND HEATER TWO-YEAR LIMITED WARRANTY: Mytee

warrants that pumps, vacuum and oor machine motors, and heaters will be free

from manufacturing defects, defects in workmanship, and defects in material for two

(2) years from the date of original purchase. This warranty does not apply and is void

if the pump, vacuum motor, or heater has worn brush motors, water damage, chemi-

cal build-up, chemical damage, or evidence of abuse, neglect or tampering. This

warranty covers the cost of replacement or repair only and does not cover shipping

or labor costs.

HOWEVER, OTHER THAN SET FORTH HEREIN, MYTEE GIVES NO WARRANTY,

EXPRESS OR IMPLIED, AS TO DESCRIPTION, QUALITY, MERCHANTABILITY,

FITNESS FOR ANY PARTICULAR PURPOSE, PRODUCTIVENESS, INFRINGE-

MENT, OR OTHER MATTER, OF ANY GOODS WHICH MYTEE SHALL SUPPLY.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION

ON THE FACE HEREOF. MYTEE SHALL IN NO WAY BE RESPONSIBLE FOR THE

PROPER USE AND APPLICATION OF THE GOODS. MYTEE NEITHER ASSUMES

NOR AUTHORIZES ANY OTHER PERSON TO ASSUME FOR MYTEE ANY OTHER

LIABILITY IN CONNECTION WITH THE SALE OF MYTEE’S GOODS. THIS LIM-

ITED WARRANTY POLICY MAY BE CHANGED OR WITHDRAWN BY MYTEE AT

ANY TIME WITHOUT NOTICE.

LIMITATION OF DAMAGES: THE REMEDY OF REPLACEMENT OR REPAIR

OF ANY DEFECTIVE GOODS SHALL BE THE EXCLUSIVE REMEDY UNDER

ANY WARRANTY MADE BY MYTEE, WHETHER EXPRESS OR IMPLIED. IN NO

EVENT SHALL MYTEE BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL

DAMAGES, PROPERTY DAMAGES, OR PERSONAL INJURIES.

All limited warranties are void for, and Mytee does not warrant in any way, any prod-

uct that evidences misapplication, improper installation, abuse, lack of maintenance,

negligence in use or care, abnormal use, alteration of design, modication, use of

incompatible or corrosive chemicals, use in a rental service, and/or servicing, installa-

tion of parts, or repairs by anyone other than Mytee or a Mytee authorized distributor

or service center. Mytee may make changes in products it manufactures and markets

at any time; these changes are made without obligation to change, retrot, or up-

grade any product previously sold or manufactured.

Mytee has no obligation to honor the limited warranties set forth herein unless the

original purchaser, promptly upon discovering the warranty claim and prior to continu-

ing to use the product, contacts Mytee or a Mytee authorized distributor or service

center to describe the claim and to receive and follow instructions for documenting

and resolving the claim. In addition, the purchaser must provide the product to which

the claim applies to Mytee or a Mytee authorized distributor or service center for a

thorough inspection. In addition, the purchaser must provide/return the product intact,

unmodied, with all of its original parts.

If any provision or portion of this limited warranty policy is found to be unenforceable,

then the remaining provisions and portions shall remain valid and enforceable.

If any provision or portion of this limited warranty policy is found to be limited by law,

then that provision or portion shall be construed to make it effective within the

bounds of law. For example, if there are legal limitations on the duration of warran-

ties, the warranties made herein shall be construed to have the minimum duration

required by law, or, if there are legal limitations of exclusion of remedies, the exclu-

sions made herein shall be construed to apply to the fullest extent possible without

violating the law.

The validity, construction and performance of this warranty policy shall be governed

by the laws of the State of California, without respect to conicts of laws principles.

The exclusive jurisdiction of any legal action arising from or related to this warranty

policy shall be in the State of California and no legal action shall be commenced

elsewhere.

Return Material Authorization Procedure

It is the responsibility of any Authorized Service Center (ASC) or Distributor with

written authorization to ensure the Customers equipment is repaired as soon as

possible. Only Mytee Products Inc. or it’s authorized dealers with written authoriza-

tion, service centers, and agents may make warranty repairs on these products. All

others do so at their own risk and expense.

The Distributor must follow Mytee Products, Inc. standard RMA procedure:

1. When a repair falls within the Warranty time period for a piece of equipment, the

Distributor will ll out a RMA/Warranty claim form. This form will act as a repair order

to replace any defective parts.

2. All defective parts must be returned to Mytee Products, Inc. with the RMA/claim

form for evaluation at the customer’s expense. This shipping is non-refundable. All

warranty claims are subject to an evaluation by Mytee Products, Inc. to determine if

warranty will be approved. Any credit for repair and/or parts will only be issued upon

evaluation and approval from Mytee Products, Inc.

3. When Warranty is approved, the Distributor’s account will be credited for the

replacement part(s). Mytee Products, Inc. will ship the warranted replacement part(s)

to the Distributor prepaid. If Warranty is denied the Distributor’s account will not be

credited for any parts sent for this claim.

GENERAL INFORMATION

HP100 GRANDPRIX™ PARTS & PRICING

Part prices are subject to change.Order parts at: http://www.mytee.com/products/product.php?id=HP100

ITEMS NOT SHOWN:

ITEM

NO.

PART NO.

DESCRIPTION

QTY.

H273

nut, kep, #10-32 zinc

H230

screw, 10-32 x 1/2 phil pan

H528

bracket, heater mounting, dual

E571

heating rod, 600W, 115V

H275

6-32 x 3/16 p-pan internal sem zinc

H274

screw, #6 x 3/16, phil pan head, self-tapping

E574

Thermostat, 310°F ± 10°F, Manual, 1/4"

E573

Thermostat, 200°, Auto, 1/4"

H903A

heater, aluminum cast, single

B103

elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt

AH108S

sol hose, 1/4" x 24 1/2", (OAL), f x fsw, 3000psi

AH156

hose, 3/8" x 6.5", (OAL), f x fsw, 5400 Gray

B207

elbow, brass, 90 deg, 1/4" fpt x 1/4" fpt

B108

valve, brass, 1/4" check

AH103

hose, 3/8" x 10", (OAL), f x fsw, surge, 1600psi

B136

elbow, brass, 90 deg, 1/4" mpt x 1/4" mpt

B105

bushing, brass, 3/8"mpt x 1/4"

C305

pump, 120psi, demand, 115V

B172

elbow, brass, 90 deg, 1/2" barb x 3/8"mpt

PH615

sol hose, 1/2" kuri 100psi

H347

clamp, hose, 5/16-29/32

B160

adapter, brass, 1/2" barb x 3/8" fsw, ball end

H217

clamp, hose, 2-1/4 dia

PH627 vac hose, 1-1/2", wire reinforced

H300

cuff, black 1-1/2"

H770

bolt, 1/4-20 x 1/2" serrated hex flange, zinc

C302 vac motor, 3 stage, 120V, tangential

H343

screw, #10 x 5/8" hex head, zinc

G004

gasket, vacuum motor

H501

vac support, 3 stage, 4-1/16"

H330

plate, single manifold, 6.5" x 9"

H204

bolt, 1/4-20 x 1-3/4" hex head, s/s

H201

bolt, 1/4-20 x 1/2", hex head, zinc

P735

manifold, single vac, no gasket

H768

bolt, 1/4-20 x 3/4" serrated hex flange, zinc

H216

nut, lock, 1/4-20, nylon insert, s/s

H222

screw, #10-32 x 1-1/4" phil pan head, zinc

H210

washer, 1/4" flat, s/s

PH628

vac hose, 2", wire reinforced

PH633-03

pipe, pvc, 1-1/2"

H244

adapter, pvc, 1-1/2" fms x fmpt

H229

fitting, inlet, pvc, 1-1/2", gray

H667

caster, 3", Black Hub, Gray Tread

H342

bolt, 1/4-20 x 1" hex head, s/s 8

H296

guard, cooling fan, wire

P756

base, firebird

H221

nut, lock, 1/2" steel

H220

fitting, strain relief, cord

E531

power cord, end, 25', 12/3 black

H254

washer, axle, cut 1/2" id

H224

axle, 17.50" x .50" dia, fb

H239

wheel, 8"

H219

cap, axle, 1/2"

P757

sol tank, firebird

G061

cover, sol tank, fb

H215

nut, hex, 1/4-20, s/s

H213

washer, 1/4" lock, s/s

H211

washer, 1/4"id x 1"od, flat, s/s

G052

washer, buna 1-1/8" od x 3/16" id

H203

bolt, 1/4-20 x 1-1/4" hex head

H316

bolt, 1/4-20 x 1-1/2" hex head, s/s

H378

bracket, front hinge, sp/fb

B119A

filter, strainer, 1/2"

B210

bushing, brass, 1/2"mpt x 3/8" fpt, hex

H299

washer, 11/16"id x 1-1/2"od x .075, s/s

B216

nipple, brass, 3/8" x close

ITEM

NO.

PART NO.

DESCRIPTION

QTY.

B186

elbow, brass, 90 deg, 3/8"mpt x 3/8" fmpt

B111

adapter, brass, extender, 1/4" mpt x 1/4" fpt, hex

H212

washer, 9/16"id x 1"od, flat, s/s

B102

qd, brass, 1/4" f

H413

washer, nylon, 9/16id x 1-1/16od x .031

B107

nipple, brass, 1/4"m, hex

AH105

hose, 3/8" x 17-1/2", (OAL), f x -fsw, surge, 1600psi

H912

bracket, rear, fb/spy

PH633-11

pipe, pvc, 1-1/2"

H297

screw, #8 x 1/2", hex head, zinc

P755

elbow, U, 180, 1-1/2", float

H235

float, 1.5", ball style

G091

gasket, 7", vac lid

G090

lid, vac tank, black, 7"

H304

screw, #8 x 5/8 phil oval, s/s

H135

Cuff-Lynx, 2" m cuff x 2" mpt

G002

gasket, cam fitting polyethylene, 2.35" OD 1.90" ID

A926

elbow, inlet assembly 2"

P758

vac tank, firebird

H225

valve, drain, 1-1/2" 1

H226

spout, drain, 45 degree

H390A

bracket, "L" (all extracters)

H326

plate, switch, 3 hole, fb

H246

screw, #8-32 x 3/8" SHCS, alloy

E515

switch, rocker, 2 position

HP100-2001CS

SHEET 1 OF 2

Grandprix

SCALE: 1:3

REV

DWG. NO.

SIZE

TITLE:

NAME

DATE

CHECKED

DRAWN

PROPRIETARY AND CONFIDENTIAL

THE INFORMATION CONTAINED IN THIS

DRAWING IS THE SOLE PROPERTY OF

MYTEE PRODUCTS, INC. ANY

REPRODUCTION IN PART OR AS A WHOLE

WITHOUT THE WRITTEN PERMISSION OF

MYTEE PRODUCTS, INC. IS PROHIBITED.

mytee

PRODUCTS, INC.

858-679-1191

V. LaBarbera

7/2011

DO NOT SCALE

DRAWING

HP100 GRANDPRIX™ PARTS & PRICING

13 14

29 23

50 51

36 62

38 57 33

85 87

68 69

138

To pump "IN"

thru B160

To filter in sol tank

thru B186

To heater "OUT"

thru AH108S

To female q.d.

thru B103

To inlet

on base

To vac

motor exhaust

thru H244

HP100 GRANDPRIX™ WIRING DIAGRAM

D D

C C

B B

A A

Mytee Products

13655 Stowe Dr.

Poway, CA

92064

---1

HP100

0000 A

3/11/2011 4:38:47 PM

Z:\Engineering\GHI\GHI Projects\MYTEE\Mytee Schematics\HP100\HP100 Schematic.SCHDOC

Title

Size: Number:

Date:

File:

Revision:

Sheet of

Time:

L egal

L 1

L 2

GND

Cord Input Primary

L 1

L 2

GND

Pressure Pump

L 1

L 2

GND

Vacuum Motor 1

L 1 L 2

GND

Heater 1

Thermal Switch

L 1 L 2

GND

Heater 2

Thermal Switch

SW- DPST

B lue

Black Black Black

Y ellow

B lack

White White

W hite

White

Orange

SW- DPST

Green

Green Green Green

T hermal S witch

C302

E571E571

C305

E515

Inline Conn.

Pressure

Switch

B lack

Inline Conn.

B lack

Inline Conn.

B lack

Inline Conn.

B lack

Inline Conn.

SW- DPST

E515

Mytee Products Inc.

13655 Stowe Dr.

Poway, Ca. 92064

www.mytee.com

PH 858.679.1191

FX 858.679.7814

Printed in the U.S.A.

NOTES

Other manuals for HP100 Grand Prix

Mytee HP100 Grand Prix User manual