Vax V-033 SERIES User manual

Vax Careline:
0870 6061248
Instruction Manual
Please read carefully before using
the carpet washer. Always fully
extend the mains cable before use.
Please retain these instructions
for future reference.
www.vax.co.uk
Portable Carpet Washer
Vax Model Number: V-033
V-033_Rapide_Comp_U_G.qxd 30/6/06 8:46 am Page 2

Fig.1/2
1. Diagram
Parts Overview
2
1
9
8
7
6
11
12
3
10
5
2
1. Carry Handle
2. On/Off Switch
3. Dirty Water Tank
4. Clean Water Tank
5. Clean Water/Solution
6. Lid Release Latch
7. Spray Nozzle
8. Solution Dispense Button
9. Power Cord
10. Attachment Hose
11. Hose Wrap
12. Quick Release Cord Hooks
13. Wash Tool
4
Fig.1/1
13
Fig.1/3
V-033_Rapide_Comp_U_G.qxd 30/6/06 8:46 am Page 3

3
Safety Information/Preparing the Machine
2. Safety Information
FOR HOUSEHOLD USE ONLY
When using the carpet washer, basic safety precautions
should always be observed, including the following:
1. Do not leave the carpet washer unattended when
plugged in. Unplug it from socket when not in use.
2. To prevent electric shock do not use outdoors.
3. Not to be used as a toy. Close supervision is
necessary when used by or near children or the
infirm.
4. Use only as described in this manual.
5. Do not use with a damaged cord or plug. If the
supply cord and/or plug is damaged, they must be
replaced by the manufacturer, a Vax Service Agent
or similarly qualified persons in order to avoid
hazard.
6. Do not pull or carry by the cord, use the cord as a
handle, allow the cord to come into contact with
hot or sharp surfaces or close a door on the cord.
7. Do not unplug by pulling on the cord.
8. Do not handle the plug or carpet washer with wet
hands.
9. Do not put any objects into openings or operate
with openings blocked, keep them free of anything
that may reduce airflow.
10. Keep hair, loose clothing, fingers and all parts of
the body away from openings and moving parts.
11. Do not use the carpet washer on any glowing,
burning or smoking particles.
12. Do not use without the solution tank and dirty
water tank in place.
13. Turn off all controls before unplugging.
14. Do not use to pick up flammable or combustible
liquids such as petrol, or use in areas where they
may be present.
15. Keep the carpet washer on the floor.
16. Do not use an extension cord.
17. Do not attempt to remove blockages with sharp
objects as they may cause damage.
18. Store indoors put away after use to prevent
tripping accidents.
19. Using improper voltage may result in damage to
the motor and possible injury to the user.The
correct voltage is listed on the rating label.
20. A hazard may occur if the carpet washer runs over
the power supply cord.
21. To prevent dirty water from running into motor, do
not hold the appliance upside-down or lay on its
side. Use appliance in normal vacuuming position.
22. Use extra care when cleaning on stairs.
23. Do not carry appliance while motor is running.
NOTE: Carpets should be dry vacuumed thoroughly
before washing.
NOTE: The carpet washer must be unplugged from
the mains socket outlet after use, and before
cleaning or maintaining the carpet washer.
IMPORTANT: This carpet washer is not intended
for commercial use.
3. Preparing the Machine
WARNING: USE ONLY VAX AAA CARPET CLEANER
WITH THIS MACHINE. USING OTHER CLEANING
SOLUTIONS MAY CAUSE EXCESSIVE FOAMING.
EXCESSIVE FOAM WILL CAUSE THE FLOAT TO
SHUT OFF THE VACUUM PREMATURELY.
USING OTHER SOAPS WILL VOID YOUR
WARRANTY.
Remove Clean Water Tank by pulling up and out of cleaner.
Filling Clean Water Tank
Fig.3/1
Fig.3/2
Press down on the Lid. Release Latch and tilt lid
towards front of cleaner to access the tanks.
Fig.3/3
V-033_Rapide_Comp_U_G.qxd 30/6/06 8:46 am Page 4

Unscrew cap and fill Clean Water Tank with solution
up to the Soap Fill Line (Diagram 3/3). Fill the rest of
the Clean Water Tank with warm tap water (MAX 400c)
up to the Water Fill Line (Diagram 3/3a).
Preparing the Machine/Attachments
4
Fig.3/3a
Fig.3/4
Replace Clean Water Tank cap and tighten firmly.
Return Clean Water Tank to cleaner (Diagram 3/4).
Close lid making surethat the Lid Release Latch
clicks into place (Diagram 3/4a).
Fig.3/4a
4. Attachments
Connecting Attachments
NOTE: Always turn off appliance before
connecting or disconnecting attachments.
Fig.4/1
Connect desired attachment by pressing tool onto
the end of the attachment hose until the locking
button snaps into the hole. WARNING: Keep spray
pointed away from face. Failure to do so may result
in personal injury.
Fig.4/2
To remove, press down on the locking button and pull
the tool away from the hose.
V-033_Rapide_Comp_U_G.qxd 30/6/06 8:46 am Page 5

Usage
5
5. Usage
IMPORTANT: Do not use the Carpet Cleaner as a
dry vacuum.
NOTE: Never leave unit unattended with power
on. Turn OFF when emptying and filling reservoir.
DO NOT oversaturate carpet or upholstery.
IMPORTANT: For best cleaning results, use
steady, moderate, forward and backward motion.
CHECK FOR COLOUR FASTNESS:
Before cleaning carpet/upholstery, test for colour
fastness. Dampen a white cloth with solution. Test a
small area somewhere discreet i.e. underneath a
cushion. Gently rub the cloth over the area. Check
each colour for colour bleeding. If the cloth remains
clean, it should be safe to clean the
carpet/upholstery.
HELPFUL HINTS FOR CLEANING CARPET:
1. Do not oversaturate carpet with cleaning solution
while using the Carpet Cleaner.
2. For heavily soiled areas, additional applications
may be necessary.
3. Allow plenty of time to dry carpet thoroughly.
4. Wipe cleaning solution from woodwork and wood
to prevent any damage.
5. Try not to walk on carpet until it is completely dry.
6. After carpet is thoroughly dry, vacuum the carpet
using a cleaner with a revolving brushroll.
Carpet and upholstery Cleaning
Plug cord into electrical outlet.
Fig.5/2
Fig.5/1
Turn ON/OFF switch to the “ON” position.
Fig.5/3
Hold the tool approximately 1” above the stained
surface. Press the solution dispense trigger to apply
cleaning solution to the stained area. NOTE: Before
using hand tool attachments, it is necessary to
prime the pump. Follow these steps for optimal
performance:
•Fill the clean water tank.
•Place hand tool attachment on floor.
•Depress the solution dispense button on hose for
10 seconds while the power is off.
•Repeat if necessary.
Fig.5/4
Gently scrub the stained area with the brush on the tool
until the stain is completely removed. Release the
solution dispense trigger and continue moving the tool
over cleaned area to remove as much liquid as possible.
V-033_Rapide_Comp_U_G.qxd 30/6/06 8:46 am Page 6