Mytee Flood Hog 7000S User manual

1
Instructions for
7000S Flood Hog™
13655 Stowe Dr., Poway, CA 92064
Model #
Serial #
Form # ADM-7000S
11-15
Please read before use.
Register your product
at: http://www.mytee.com/
support/register
General information p. 2
Set up p. 4
Parts & Pricing p. 9
Wiring diagram p. 11
Notes p.12
REVISIONS
REV. DESCRIPTION DATE APPROVED
OD ORIGINAL DRAFT JFL
D
C
B
A
B
C
D
1 2 3
4 5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
7000S
SHEET 1 OF 1
Flood Hog (2014)
OD
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:8
REV
DWG. NO.
C
SIZE
TITLE:
NAME DATE
COMMENTS:
CHECKED
DRAWN
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
ANGULAR: MACH
.5
ONE PLACE DECIMAL
.03
TWO PLACE DECIMAL
.05
THREE PLACE DECIMAL
.003
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
V. LaBarbera

2
Dear Customer:
Congratulations on the purchase of your new 7000S Flood Hog™. As you
are already aware, the scene of the equipment world is becoming more high tech,
and we at Mytee Products Inc. strive to keep you on the cutting edge with superior
quality and technology.
Keep in mind that the 7000S Flood Hog™ is a machine, so neglect or abuse will
cause unnecessary damage and void the warranty. However with simple mainte-
nance the Flood Hog™ will give quality performance for many years to come.
If warranty questions arise, please consult your user manual or get in touch with
your distributor. If you have questions about maintenance, replacing parts or
ordering parts, please call an authorized Mytee Products Inc. Service Center.
To see an updated list, visit our website at www.mytee.com
Before you begin cleaning, please read your manual thoroughly.
Sincerely,
Mytee Customer Care Dept.
Grounding Instructions
This machine must be grounded. If it should malfunction or break down, grounding
provides a path of least resistance for electrical shock. This machine is equipped
with a cord having an equipment-grounding conductor and grounding plug. The plug
must be plugged into an appropriate outlet that is properly installed in accordance
with all local code and ordinances. Do not remove ground pin; if missing, replace
plug before use.
Improper connection of the equipment-grounding conductor can result in a risk of
electric shock. Check with a qualied electrician or service person if you are in doubt
as to whether the outlet is properly grounded. Do not modify the plug provided with
the machine. If it will not t the outlet, have a proper outlet installed by a qualied
electrician.
This appliance is for use on a nominal 120-volt circuit, and has a grounding plug
that looks like the plug illustrated in Figure 1 below. A temporary adapter illustrated
in Figures 2 and 3 may be used~to connect this plug to a 2-pole receptacle as
shown in Figure 2 if a properly grounded outlet is not available. The temporary
adapter should be used only until a properly grounded outlet (Figure 1) can be
installed by a qualied electrician. The green colored rigid ear, tab or the like
extending from the adapter must be connected to a permanent ground such as a
properly grounded outlet box cover. Whenever the adapter is used, it must be held
in place by a metal screw. Grounding adapters are not approved for use in Canada.
Replace the plug if the grounding pin is damaged or broken.
The green (or green-yellow) wire in the cord is the grounding wire. When replacing
a plug, this wire must be attached to the grounding pin only.
DO NOT use extension cords.
Please Note for America use only
Parts and Service
Repairs, when required, should be performed by Mytee service personnel or Mytee
authorized Service Center using Mytee original replacement parts and accessories.
Call Mytee for repair parts or service. Please specify the Model and Serial Number
when discussing your machine.
Name Plate
The Model and Serial Number of your machine are shown on the Nameplate on the
back panel of the machine. This information is needed when ordering repair parts
for the machine. Use the space provided on the front cover to note the Model and
Serial Number of your machine for future reference.
Unpacking the Machine
When the machine is delivered, carefully inspect the shipping carton and the
machine for damage. If damage is evident, save the shipping carton so that it can
be inspected by the carrier that delivered it. Contact the carrier immediately to le a
freight damage claim.
Caution and Warnings
Symbols
Mytee uses the symbols below to signal potentially dangerous conditions. Always
read this information carefully and take the necessary steps to protect personnel
and property.
Is used to warn of immediate hazards that will cause severe personal injury or death.
Is used to call attention to a situation that could cause severe personal injury.
Is used to call attention to a situation that could cause minor personal injury or
damage to the machine or other property. When using an electrical appliance, basic
precautions should always be followed, including the following: Read all instructions
before using this machine. This product is intended for commercial use only.
To reduce the risk of re, electrical shock, or injury:
1. Read all instructions before using equipment.
2. Use only as described in this manual. Use only manufacturer’s recommended
attachments.
3. Always unplug power cord from electrical outlet before attempting any adjustments
or repairs.
4. Do not unplug by pulling on cord. To unplug, grasp the plug, not the cord.
5. Do not pull by cord. Do not close a door on cord or pull cord around sharp edges
or corners.
6. Do not run appliance over cord. Keep cord away from heated surfaces.
7. Do not use with damaged cord or plug. If cord is damaged, repair immediately.
8. Always unplug or disconnect the appliance from power supply when not in use.
9. Do not allow to be used as a toy. Close attention is necessary when used by or
near children.
10. Do not use in areas where ammable or combustible material may be present.
11. Do not leave the unit exposed to harsh weather elements. Temperatures below
freezing may damage components and void warranty.
12. Use only the appropriate handles to move and lift unit. Do not use any other parts
of this machine for this purpose.
13. Keep hair, loose clothing, ngers, and all parts of the body away from all
openings and moving parts.
14. Use extra care when cleaning on stairs.
15. To reduce the risk of re or electric shock, do not use this machine with a solid-
state speed control device.
16. The voltage and frequency indicated on the name plate must correspond to the
wall receptacle supply voltage.
17. When cleaning and servicing the machine, local or national regulations may apply
to the safe disposal of liquids which may contain: chemicals, grease, oil, acid,
alkalines, or other dangerous liquids.
18. Do not leave operating unattended.
Pre-Operation
1. Remove furniture and other items from the area you are going to treat.
2. Make sure debris lter is clear and electrical cord is in good repair.
3. Make sure a 20A grounded wall outlet is available for cord. Do not use
extension cord.
Operation
1. In front, attach one end of the rst vacuum hose to a wand (using scalloped or
squeegee vacuum head), the other end to the Cuff-Lynx™ hose connection on the
front of the machine.
2. The debris lter inside the machine protects the vacuum motor from damaging
debris. Keep it clean by removing vacuum hose and turning the top latch counter-
clockwise and opening the lid. Remove stainless steel basket and gently rinse with
water. Dry with a soft cloth. Replace basket, lid and hose.
3. In back, attach the second vacuum hose bearing cam lock to the Auto Pump-out
tting. Secure the hose to the tting using the cam lock. Push the hose cuff onto
the tting, making sure the silver ears and rings are extended forward. Pull the ears
Figure 1
Grounding Pin
Grounded Outlet
Grounded Outlet Box
Adapter
Tab for Grounding
Screw
Metal
Screw
Figure 2 Figure 3
GENERAL INFORMATION

3
down using the rings until connection is tight. Place the end of the hose in a location
where dirty water can drain.
4. Two power cords are located in the back of the machine. To power Vacuum 1 and
Pump, plug in the top cord. To power the Vacuum 2, plug in the bottom cord. Plug
each of the two power cords into two separate, 20A grounded wall outlets. Do not
use extension cords.
5. Three switches are located on the lower left side of the machine. To use the
vacuum 1, turn on the Vacuum 1 switch. To use Vacuum 2, turn on the Vacuum 2
switch. To use the pump, turn on the Pump switch.
6. Place wand over ooded area and begin extracting.
7. If pump must be accessed during extraction, use the recovery tank lid on top of
the machine. Pull the lever up and turn counter clockwise until it faces the side of the
machine. Pull up and take the lid off. Use reverse procedure to replace.
8. When the job is nished, turn off switches and unplug power cords. Remove
hoses.
After Use
1. Unplug.
2. Inspect hoses and replace if damaged.
3. Inspect lter and clean.
4. Open recovery tank to promote air circulation
5. Make sure machine and hoses are completely drained and dry.
6. Store the machine in a clean, dry place.
Maintenance Schedule
Maintenance item Daily Once a week
Clean and inspect Tanks
Clean and inspect Hoses
Inspect lters
Check electrical cord
Clean machine with all purpose cleaner and cloth
Inspect vacuum hoses for holes and loose cuffs
Lubricate wheels with water-resistant oil
Inspect machine for water leaks and loose hardware
x
x
x
x
x
x
x
x
Trouble Shooting
There is no power.
1. Plug machine in proper outlet.
2. Check circuit breaker; reset circuit breaker, other items should not run on the
same circuit as machine. Outlet must be a 20-amp circuit. For 7000S models, two
separate 20-amp circuits are required.
Pump does not work properly.
1. Check pump wire. May need to reconnect wire.
2. Switch plate switch may need to be replaced.
3. If pump motor brushes are worn, replace pump.
4. Float switch obstructed. Clean.
Vacuum motor does not work properly.
1. Check that hose is tightly connected.
2. Close drain hose valve completely.
3. Secure the vacuum tank tightly.
4. If water is coming out of vacuum motor, use a low foaming detergent.
FAQs
Q: How much does the 7000S weigh and what are the shipping dimensions?
A. 7000S weighs 124 pounds - Box dimensions are 20” x 30” x 48”. Must ship motor
freight.
Q: What comes standard with the 7000S?
A: The 7000S comes with two 25’ vacuum hoses (H294), a wand (H908), a vacuum
head (P570), a squeegee vacuum head (G200) a 2” x 1.5” Cuff Lynx™ (H141), two
2” Cuff-Lynx™ plugs (H121), and pack of lters (G008).
Q: Where do I plug the machine in?
A: Plug each power cord into a separate, 20A grounded wall outlet. Outlets must
be on two separate breakers. When the amber light on the switch plate illuminates,
the machine is on separate circuits (not necessarily 20A circuits). You can identify the
primary cord by the yellow tag.
Q: Is there anything I can do to increase the expected life of my machine?
A: Running the vacuum motors with the tank empty and lid off will allow excess
moisture in the vacs to dry off.
GENERAL INFORMATION

4
REVISIONS
REV. DESCRIPTION DATE APPROVED
OD ORIGINAL DRAFT JFL
D
C
B
A
B
C
D
1 2 3
4 5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
7000S
SHEET 1 OF 1
Flood Hog (2014)
OD
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:8
REV
DWG. NO.
C
SIZE
TITLE:
NAME DATE
COMMENTS:
CHECKED
DRAWN
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
ANGULAR: MACH
.5
ONE PLACE DECIMAL
.03
TWO PLACE DECIMAL
.05
THREE PLACE DECIMAL
.003
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
V. LaBarbera
REVISIONS
REV. DESCRIPTION DATE APPROVED
OD ORIGINAL DRAFT JFL
D
C
B
A
B
C
D
1 2 3
4 5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
7000S
SHEET 1 OF 1
Flood Hog (2014)
OD
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:8
REV
DWG. NO.
C
SIZE
TITLE:
NAME DATE
COMMENTS:
CHECKED
DRAWN
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
ANGULAR: MACH
.5
ONE PLACE DECIMAL
.03
TWO PLACE DECIMAL
.05
THREE PLACE DECIMAL
.003
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
V. LaBarbera
7000S BACK
7000S FRONT
1. Recovery Tank Lid
2. Operating Controls
3. Handles
4. EZ Open Service Latches
5. Drain Valve
6. Vacuum Hose Hook-up
7. 2” Female Cuff-Lynx™ starter
8. 2” Male Cuff-Lynx™ plug
9. 25’ Power Cord
10. 10” Stair Climbing Wheels
11. 4” Swivel Locking Casters
12. Auto Pump-out Hose Connection
3
2
8
5
4
6
7
9
1
10 11
12
WAND INTERCHANGEABLE HEADS
Select either vacuum head and attach to wand. Insert head and
tighten collar.
7000S ACCESSORIES
H908 - 2 Piece Aluminum P570 - Scalloped Vacuum Head
Wand Tube
G200 - Squeegee Vacuum Head
H294 - 1.5” x 25’ Vacuum
Hose (x2)
FILTERS
G008 - Pack Of Filters
H141 - 2” x 1.5”
Cuff Lynx™ Reducer
H121 - 2”
Cuff Lynx™ Plug
7000S FLOOD HOG™
H226 - Drain Elbow
D
C
B
A
A
B
C
D
1
2
3
4 5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
H226
SHEET 1 OF 1
spout, drain, 45 degree
SCALE: 1:2
REV
DWG. NO.
D
SIZE
TITLE:
NAME DATE
CHECKED
DRAWN
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS PROHIBITED.
mytee
PRODUCTS, INC.
858-679-1191
J.Cash
DO NOT SCALE
DRAWING

5
Plug each power cord into a separate, 20A grounded wall outlet.
Outlets must be on two separate breakers. When the amber
light on the switch plate illuminates, the machine is on separate
circuits (not necessarily 20A circuits). You can identify the primary
cord by the yellow tag.
Attach the second hose bearing cam lock to the Auto Pump-out
tting. Secure the hose to the tting using the cam lock. Push the
hose cuff onto the tting, making sure the silver ears and rings are
extended forward. Pull the ears down using the rings until con-
nection is tight. Place the end of the hose in a location where dirty
water can drain.
7000S BACK VACUUM HOSE/AUTO PUMP-OUT
HOOK UP
Attach the hose with the 1.5” Cuff-Lynx™ reducer to the machine.
Attach other end of same hose to wand tube.
7000S FRONT VACUUM/DEBRIS FILTER HOSE
HOOK UP
7000S SWITCHES
Three switches are located on the lower left side of the machine.
To use either vacuum, turn on the Vacuum switch 1 or 2. To use
the pump, turn on the Pump switch.
VACUUM 1 VACUUM 2 PUMP
REVISIONS
REV. DESCRIPTION DATE APPROVED
OD ORIGINAL DRAFT JFL
D
C
B
A
B
C
D
1 2 3
4 5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
7000S
SHEET 1 OF 1
Flood Hog (2014)
OD
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:8
REV
DWG. NO.
C
SIZE
TITLE:
NAME DATE
COMMENTS:
CHECKED
DRAWN
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
ANGULAR: MACH
.5
ONE PLACE DECIMAL
.03
TWO PLACE DECIMAL
.05
THREE PLACE DECIMAL
.003
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
V. LaBarbera
7000S DUAL CORDS
Top cord: Powers Vac 1 & Pump.
Bottom cord: Powers Vac 2.
Yellow tag
indicates primary
cord.
7000S FLOOD HOG™
Dual circuit
indicator light.

6
7000S DRAIN VALVE AND SPOUT
When not using the Auto Pump-out, empty the tank by using the
drain valve on the front of the machine with the included drain
elbow (part # H226).
REVISIONS
REV. DESCRIPTION DATE APPROVED
OD ORIGINAL DRAFT JFL
D
C
B
A
B
C
D
1 2 3
4 5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
7000S
SHEET 1 OF 1
Flood Hog (2014)
OD
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:8
REV
DWG. NO.
C
SIZE
TITLE:
NAME DATE
COMMENTS:
CHECKED
DRAWN
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
ANGULAR: MACH
.5
ONE PLACE DECIMAL
.03
TWO PLACE DECIMAL
.05
THREE PLACE DECIMAL
.003
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
V. LaBarbera
7000S WATER LEVEL CONTROL SWITCHES
As the water level reaches the pump-out water level control
switch, the pump is activated. Once the water level reaches the
vacuum water level control switch, the vaccum shuts off prevent-
ing the water from going into the vacuum stack, damaging the
vacuum motors. At the top of the vaccum stack, there is a lter.
Clean it weekly.
7000S FLOOD HOG™
REVISIONS
REV. DESCRIPTION DATE APPROVED
OD ORIGINAL DRAFT JFL
D
C
B
A
B
C
D
1 2 3
4 5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
7000S
SHEET 1 OF 1
Flood Hog (2014)
OD
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:8
REV
DWG. NO.
C
SIZE
TITLE:
NAME DATE
COMMENTS:
CHECKED
DRAWN
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
ANGULAR: MACH
.5
ONE PLACE DECIMAL
.03
TWO PLACE DECIMAL
.05
THREE PLACE DECIMAL
.003
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
V. LaBarbera
Pump-out water
level control switch
Vacuum water level
control switch
Vacuum stack lter
REVISIONS
REV. DESCRIPTION DATE APPROVED
OD ORIGINAL DRAFT JFL
D
C
B
A
B
C
D
1 2 3
4 5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
7000S
SHEET 1 OF 1
Flood Hog (2014)
OD
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:8
REV
DWG. NO.
C
SIZE
TITLE:
NAME DATE
COMMENTS:
CHECKED
DRAWN
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
ANGULAR: MACH
.5
ONE PLACE DECIMAL
.03
TWO PLACE DECIMAL
.05
THREE PLACE DECIMAL
.003
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
V. LaBarbera
REAR PLUGS
Two vacuum plugs are located in the back. The top and bottom rear plugs, depending on how they are capped, allow the Flood Hog™ to
be used as a stand-alone extractor, a ow-through booster connected to another machine, or an in-line pump-out unit. They also seal the
Flood Hog™ vacuum tank.
Cap both plugs
to use as a
ood extractor
Cap top plug to use as
a booster and pass-through
extractor.
See page 6.
Cap bottom plug
to use as booster
with pump-out
See page 6.

7
7000S FLOOD HOG™ IN USE
Flood Hog™ pumps up to 35 GPM.
FLOODED AREA
DRAIN
The lter protects the vacuum motor from damaging debris. Keep
it clean by removing the vacuum hose and opening the recovery
tank lid via the latch on the front of the machine. Remove stain-
less steel basket and gently rinse with water. Dry with a soft cloth.
Replace basket, lid and hose.
7000S LATCHES AND LIFT HANDLE
REVISIONS
REV. DESCRIPTION DATE APPROVED
OD ORIGINAL DRAFT JFL
D
C
B
A
B
C
D
1 2 3
4 5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
7000S
SHEET 1 OF 1
Flood Hog (2014)
OD
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:8
REV
DWG. NO.
C
SIZE
TITLE:
NAME DATE
COMMENTS:
CHECKED
DRAWN
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
ANGULAR: MACH
.5
ONE PLACE DECIMAL
.03
TWO PLACE DECIMAL
.05
THREE PLACE DECIMAL
.003
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
V. LaBarbera
LATCHES:
Detach: Flip-up latch.
Twist counter clock-
wise for release.
Attach: Place latch.
Twist clockwise
Press latch to secure.
REVISIONS
REV. DESCRIPTION DATE APPROVED
OD ORIGINAL DRAFT JFL
D
C
B
A
B
C
D
1 2 3
4 5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
7000S
SHEET 1 OF 1
Flood Hog (2014)
OD
UNLESS OTHERWISE SPECIFIED:
SCALE: 1:12
REV
DWG. NO.
C
SIZE
TITLE:
NAME DATE
COMMENTS:
CHECKED
DRAWN
FINISH
MATERIAL
DIMENSIONS ARE IN INCHES
TOLERANCES:
ANGULAR: MACH
.5
ONE PLACE DECIMAL
.03
TWO PLACE DECIMAL
.05
THREE PLACE DECIMAL
.003
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS
DRAWING IS THE SOLE PROPERTY OF
MYTEE PRODUCTS, INC. ANY
REPRODUCTION IN PART OR AS A WHOLE
WITHOUT THE WRITTEN PERMISSION OF
MYTEE PRODUCTS, INC. IS
PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
V. LaBarbera
7000S DEBRIS FILTER
LIFT HANDLE: Use lift handle to prevent damage to unit.
7000S FLOOD HOG™

8
3. USING THE FLOOD HOG™ AS A BOOSTER WITH AUTO PUMP-OUT
The optional pump-out can be used in conjunction with a second, larger extractor (#1), which will be used as a clean water
source. A. Connect a vacuum and solution hose to the larger extractor (#1) and the Flood Hog’s™ (#2) rear top plug. Keep the bottom
rear vacuum plug capped. B. Attach the wand’s vacuum hose to the Flood Hog’s™ front vacuum port and attach the solution hose to the
larger extractor’s QD. C. Connect the Flood Hog’s™ pump-out hose to the Flood Hog™ via the cam-lock tting on the rear of the machine.
Turn on the pump-out switch. Dirty water will be automatically pumped out of the Flood Hog™.
4. USING THE FLOOD HOG™ AS A BOOSTER AND PASS-THROUGH EXTRACTOR
The Flood Hog™ (#2) can be used as a pass-through extractor and to boost the airow of a second, larger extractor (#1) by
increasing its CFM by 113. A. To do this, use the larger extractor (#1) as a fresh water source and recovery tank, connect a vacuum hose
to the larger extractor and the Flood Hog’s™ (#2) rear bottom plug. Keep the top rear plug capped. B. To use a wand, attach the wand’s
vacuum hose to the front of the Flood Hog™ and attach the solution hose to larger extractor and to the wand. Clean water will travel from the
larger extractor to the wand to clean the surface, and dirty water will be drawn through the Flood Hog™ into the main extractor’s recovery
tank.
Drain
Dirty water recovery
Solution ow
Pump-out system
Base extractor airow
* Wand & extractor not included with Flood Hog™
* Wand & extractor not included with Flood Hog™
Dirty water recovery
Solution ow
A
B
C
A
B
#2
#2
#1
#1
7000S FLOOD HOG™

9
Part prices are subject to change.Order parts at: www.mytee.com
7000S FLOOD HOG™ PARTS & PRICING
ITEMS NOT SHOWN
ITEM
NO.
PART NO.
DESCRIPTION
QTY.
MSRP
1
G106
gasket, vac lid, 7000S
1
$21.99 ea
2
H135
Cuff-Lynx, 2" m cuff x 2" mpt
1
$3.99 ea
3
P740
lid, 7000S
1
$96.99
4
H217
clamp, hose, 2-1/4 dia
5
$1.49 ea
5
PH628-10
vac hose, 2", black, wire reinforced
1
$8.99 ft
6
C302A
vac motor, 3-stage hp, 120V, 145"
2
$148.99 ea
7
H770
bolt, 1/4-20 x 1/2" serrated hex flange, zinc
6
$0.99 ea
8
H501
vac support, 3 stage, 4-1/16"
6
$4.99 ea
9
G004
gasket, vacuum motor
2
$8.99 ea
10
H202
bolt, 1/4-20 x 3/4" hex head, s/s
6
$0.99 ea
11
P735
manifold, single vac, no gasket
2
$14.99 ea
12
H253
plate, dual manifold, 9" x 13"
1
$14.99 ea
13
H225
valve, drain, 1-1/2" 1
$20.99 ea
14
H485
handle, aluminim grip, black
3
$6.99 ea
15
G052
washer, buna 1-1/8" od x 3/16" id
4
$1.99 ea
16
H768
bolt, 1/4-20 x 3/4" serrated hex flange, zinc
6
$0.99 ea
17
H906
latch, front, small, 7000S
1
$18.99 ea
18
P741
flood hog, vac tank
1
$193.99 ea
19
H023
filter basket, flood hog
1
$64.99 ea
20
C384
pump out, 35 gpm, 115v, stainless
1
$429.99 ea
21
P686
swing check valve, pump out
1
$24.49 ea
22
PH627-7
vac hose, 1-1/2", black, wire reinforced
1
$4.99 ft
23
PH633-1
pipe, pvc, 1-1/2"
1
$4.99 ft
24
G003 filter, foam, 2" x .50" o.d.
1
$1.99 ea
25
G097
screen, mesh filter, 1-1/2" dia
1
$4.99 ea
26
P502
adapter, 1.5" pvc, fslip x fslip
1
$5.00 ea
27
PH633-12
pipe, pvc, 1-1/2"
1
$4.99/ft
28
H244
adapter, pvc, 1-1/2" fms x fmpt
1
$4.99 ea
29
H396
barb, 1-1/2" x 1-1/2" fpt, pump out
1
$19.99 ea
30
H207
cam & grovve fitting 1-1/2", male
1
$21.99 ea
31
H121
cuff-lynx, 2" plug
2
$3.99 ea
32
G122 o-ring, 2.318" OD x 3/32" width
2
$2.99 ea
33
H124
Cuff-Lynx, 2" mpt x 2" female cuff
2
$3.99 ea
34
P680
elbow, pvc 1/2" fmt x 1/2" fms
1
$2.00 ea
35
B210
bushing, brass, 1/2"mpt x 3/8" fpt, hex
4
$2.49 ea
36
B105
bushing, brass, 3/8"mpt x 1/4"
2
$3.19 ea
37
B103
elbow, brass, 90 deg, 1/4"mpt x 1/4" fpt
2
$4.49 ea
38
E373
level switch, vacuum shut-off, rear threads
2
$13.99 ea
39
B216
nipple, brass, 3/8" x close
1
$1.99 ea
40
H299
washer, 11/16"id x 1-1/2"od x .075, s/s
1
$0.99 ea
41
P679
adapter, pvc, 1/2" fpt x s
1
$3.99 ea
42
P677-2
pipe, pvc, 1/2" x 20'
1
$1.99 ft
43
P575
TEE 1/2" FSlip x 1/2" FSlip x 1/2" FPT
1
$0.99 ea
44
P677-2.5
pipe, pvc, 1/2" x 20'
1
$1.99 ft
45
H221
nut, lock, 1/2" steel
3
$1.99 ea
46
H220
fitting, strain relief, cord
3
$3.19 ea
47
H229
inlet, pvc, 1-1/2", gray
1
$5.99 ea
48
H300
cuff, hose, 1-1/2 x 1-1/2, wire
1
$5.99 ea
49
PH627-15
vac hose, 1-1/2", black, wire reinforced
1
$4.99 ft
50
G059
exhaust boot, plastisol
1
$4.99 ea
51
H042
c-clip, 12mm, external
2
$0.99 ea
52
H392
wheel, 10"
2
$35.49 ea
53
H254
washer, axle, cut 1/2" id
4
$0.99 ea
54
H371
axle, 18.03" x .50" dia
1
$9.99 ea
55
H668
caster, 4", black hub & gray tread
2
$19.49 ea
56
H342
bolt, 1/4-20 x 1" hex head, s/s
8
$0.99 ea
57
H210
washer, 1/4" flat, s/s
8
$0.99 ea
58
H211
washer, 1/4"id x 1"od, flat, s/s
2
$0.99 ea
59
H296
guard, cooling fan, wire
2
$2.99 ea
60
H304
screw, 8 x 5/8", phil oval, s/s
8
$0.99 ea
61
H486
latch, front
2
$13.99 ea
62
H230
screw, 10-32 x 1/2" phil pan head, s/s
32 $0.99 ea
ITEM
NO.
PART NO.
DESCRIPTION
QTY.
MSRP
63
H273
nut, kep, #10-32 zinc
15 $0.99 ea
64
E512B
light, indicator, 125v (amber)
1
$9.99 ea
65
P967A
plug
1
$1.99 ea
66
E515
switch, rocker, 2 position
3
$13.99 ea
67
H389
screw, 10-32 x 1/2" SHCS, alloy
1
$0.99 ea
68
H612
washer, 8 flat, s/s
1
$0.99 ea
69
H641
plate, switch, RL1200, 7000DX
1
$6.99 ea
70
G068
bumper, 7/8" x 1/4" head
2
$1.99 ea
71
H186
screw, 10-32 x 3/4, phil flat full thread
6
$0.99 ea
72
E564
controller, circuit light
1
$62.99 ea
73
E370
controller, water level, dual pump or vac
1
$133.99 ea
74
E628
controller, water level, single, 115V
1
$114.99 ea
75
H487
bracket, hinge
2
$4.49 ea
76
E550
power cord, pigtail, 30", 12/3, black
2
$11.49 ea
77
P696
base, breeze
1
$135.99 ea
PART NO.
DESCRIPTION
QTY.
MSRP
H141
Cuff-Lynx, 2" x 1.5" reducer
1
$3.99 ea
H908
flood wand, two piece, extraction
1
$62.99 ea
P570
head, scalloped, grey, wet\dry vacuuming
1
$20.99 ea
G109
gasket, strip, vac lid, 7000S
1
$10.99 ea
G200
squeegee, head w\blades, black
1
$29.99 ea
H294
hose, vac fx 1-1/2" x 25' sw cuffs
2
$73.99 ea
H205
female cam and groove, 1-1/2"
1
$32.99 ea
E530
power cord, ext 50', 12/3
2
$74.99 ea
P568A
cord lock, s-type
2
$8.99 ea
H226
spout, drain, 45 degree
1
$3.99 ea
D
C
B
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
7000S
SHEET 1 OF 3
Flood Hog (2014)
A
SCALE: 1:32
REV
DWG. NO.
C
SIZE
TITLE:
NAME
DATE
COMMENTS:
CHECKED
DRAWN
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
V. LaBarbera

10
7000S FLOOD HOG™ PARTS & PRICING
1
2
3
5
6
7
8
9
10
11
12
13
14
15
16
18
19 20
23
24
25
26 27 28 29
30
33
31
34 35 36
37
38
35
39
40
35
41
42
43 44
47 48
50
51
52
53
54
55
56
59
60
61
62
64
62
65
66
67
68
69
70
71 63
72 73
74
75
62
62
45 46 76
77
57
21
22
4
63
63
49
46
45
32
17
16
58
14
D
C
B
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
E
F
E
F
7000S
SHEET 2 OF 3
Flood Hog (2014)
A
SCALE: 1:32
REV
DWG. NO.
C
SIZE
TITLE:
NAME
DATE
COMMENTS:
CHECKED
DRAWN
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF MYTEE PRODUCTS, INC. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSION OF MYTEE PRODUCTS, INC. IS PROHIBITED.
A
DO NOT
SCALE DRAWING
858-679-1191
mytee
PRODUCTS, INC.
V. LaBarbera

11
7000S FLOOD HOG™ WIRING DIAGRAM
7000S Wire Schematic
L1 L2
G
L1 L2
G
VAC 1
L1L2
G
VAC 2
L2L1
G
E-515 E-515
E-515
Pump
Out
L2L1
G
E-564
L1a L1b L2a L2b
light C-302A C-302A
C-384
E-512
Cord 2
Cord 1
E-628
Ground to
metal plate
3/12/2015
Float
Switch
E-370
Float
Switch

12
NOTES
Mytee Products Inc.
13655 Stowe Dr.
Poway, CA 92064
www.mytee.com
FX 858.679.7814
© 2015 Mytee Products Inc.
Printed in the U.S.A.