National Instruments NI 9469 User manual

NI-9469 Getting
Started
2022-07-06

Contents
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Safety Guidelines for Hazardous Locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Electromagnetic Compatibility Guidelines. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Special Conditions for Marine Applications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
NI 9469 Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Connecting the NI 9469. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Routing the NI 9469. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
NI 9469 Application. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Topologies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Activity LEDs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Sleep Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
NI-9469 Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
I/O Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Cable. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Power Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Physical Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Safety Voltages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Safety Compliance and Hazardous Locations Standards. . . . . . . . . . . . . . . . . . . 11
Electromagnetic Compatibility. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
CE Compliance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Product Certifications and Declarations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Shock and Vibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Environmental. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Environmental Management. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
电子信息产品污染控制管理办法（中国 RoHS）. . . . . . . . . . . . . . . . . . . . . . . . . . . 13
NI Services. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
ni.com
2
NI-9469 Getting Started

Overview
This document explains how to connect to the NI-9469.
Note Before you begin, read the NI-9469 Safety, Environmental, and
Regulatory Information document on ni.com/manuals and complete the
soware and hardware installation procedures in your chassis
documentation.
Note The guidelines in this document are specific to the NI-9469. The
other components in the system might not meet the same safety ratings.
Refer to the documentation for each component in the system to
determine the safety and EMC ratings for the entire system.
Safety Guidelines
Caution Observe all instructions and cautions in the user documentation.
Using the product in a manner not specified can damage the product and
compromise the built-in safety protection.
Attention Suivez toutes les instructions et respectez toutes les mises
en garde de la documentation d'utilisation. L'utilisation du produit de
toute autre façon que celle spécifiée risque de l'endommager et de
compromettre la protection de sécurité intégrée.
Safety Guidelines for Hazardous Locations
The NI-9469 is suitable for use in hazardous locations; , and hazardous locations;
and nonhazardous locations only. Follow these guidelines if you are installing the
NI-9469 in a potentially explosive environment. Not following these guidelines may
result in serious injury or death.
© National Instruments 3
NI-9469 Getting Started

Caution Do not disconnect I/O-side wires or connectors unless power has
been switched o or the area is known to be nonhazardous.
Caution Do not remove modules unless power has been switched o or
the area is known to be nonhazardous.
Caution Substitution of components may impair suitability for Class I,
Division 2, or Zone 2.
Caution The system must be installed in an enclosure certified for the
intended hazardous (classified) location, having a tool secured cover/door,
where a minimum protection of at least IP54 is provided.
Special Conditions for Hazardous Locations Use in Europe and
Internationally
The NI-9469 has been evaluated as equipment under DEMKO ATEX and is IECEx
certified. Each NI-9469 is marked and is suitable for use in Zone 2 hazardous
locations, in ambient temperatures of -40 °C ≤ Ta ≤ 70 °C. If you are using the NI-9469
in Gas Group IIC hazardous locations, you must use the device in an NI chassis that
has been evaluated as Ex nC IIC T4, Ex IIC T4, Ex nA IIC T4, or Ex nL IIC T4 equipment.
Caution Transient protection shall be provided that is set at a level not
exceeding 140% of the peak rated voltage value of 85 V at the supply
terminals to the equipment.
Caution The system shall only be used in an area of not more than
Pollution Degree 2, as defined in IEC/EN 60664-1.
Caution The system shall be mounted in an ATEX/IECEx-certified
enclosure with a minimum ingress protection rating of at least IP54 as
defined in IEC/EN 60079-15.
ni.com
4
NI-9469 Getting Started

Caution The enclosure must have a door or cover accessible only by the
use of a tool.
Electromagnetic Compatibility Guidelines
This product was tested and complies with the regulatory requirements and limits
for electromagnetic compatibility (EMC) stated in the product specifications. These
requirements and limits provide reasonable protection against harmful interference
when the product is operated in the intended operational electromagnetic
environment.
This product is intended for use in industrial locations. However, harmful
interference may occur in some installations, when the product is connected to a
peripheral device or test object, or if the product is used in residential or
commercial areas. To minimize interference with radio and television reception and
prevent unacceptable performance degradation, install and use this product in strict
accordance with the instructions in the product documentation.
Furthermore, any changes or modifications to the product not expressly approved
by National Instruments could void your authority to operate it under your local
regulatory rules.
Caution To ensure the specified EMC performance, operate this product
only with shielded cables and accessories.
Special Conditions for Marine Applications
Some products are approved for marine (shipboard) applications. To verify marine
approval certification for a product, visit ni.com/product-certifications, search by
model number, and click the appropriate link.
Notice In order to meet the EMC requirements for marine applications,
install the product in a shielded enclosure with shielded and/or filtered
power and input/output ports. In addition, take precautions when
© National Instruments 5
NI-9469 Getting Started

designing, selecting, and installing measurement probes and cables to
ensure that the desired EMC performance is attained.
NI 9469 Overview
The NI-9469 is a synchronization module for C Series platforms. It has a configurable
multi-port interface that enables distribution of triggers and clocks from a host
chassis, and an onboard DDS and PLL for clock generation and synchronization
capabilities.
Connecting the NI 9469
The NI-9469 has three RJ45 connectors on the front panel labeled Port 0, 1, and 2.
These connectors use standard straight through CAT 5e Ethernet cabling to provide
connection to other NI-9469 modules only . Each port is soware configurable to
drive or receive four dierential signals through the cable, which are referred to as
Line 0 to 3. Each port can carry either four triggers, or three triggers and one clock,
in which Line 3 is dedicated to carry the clock.
Routing the NI 9469
The NI-9469 features a configurable crosspoint switch. You can control the routing
of signals and the onboard clock generator between each front port and the trigger
lines in the backplane. However, the crosspoint switch is not a full routing matrix.
You can connect only the same Line or Trig number. For example, Line 0 to Trig 0,
but not Line 0 to Trig 2. However, you can route clock signals on only Line 3 or Trig 3.
The following figure details the crosspoint switch's routing capabilities.
Note You can set only eight of the 12 total port lines as outputs due to
power constraints.
ni.com
6
NI-9469 Getting Started

Figure 1. Routing Capabilities of the Crosspoint Switch
Note The preceding figure details hardware routing capability only.
Soware imposed limitations may prevent certain routing or input/output
functions from being realized. For more information, refer to the
documentation for your specific soware platform.
NI 9469 Application
In a basic application, a single NI-9469 module is inserted into each host C Series
chassis. One module is set as master, the remainder as slaves, and all modules are
connected with a tree topology. Figure 2 shows a tree topology example. More
advanced and customizable options create a flexible topological network of NI-9469
modules. Refer to the Topologies section for examples of various topological
networks.
Based on user needs, you may desire certain topologies over others due to
application or timing requirements. Because signals are physically propagated over
cabling, the module cannot compensate for inherent cable delays and skew. For
example, if all slave modules must receive triggers at the same time with minimal
skew and delay, a star topology with short length-matched cables is preferred. Refer
to Figure 3 for a star topology configuration example.
If maximum separation distance is required, connect the modules using a daisy
chain topology with maximum cable length per hop, as shown in Figure 4. Refer to
the Cable section for information about maximum cable length.
© National Instruments 7
NI-9469 Getting Started

Topologies
Figure 2. Tree Topology
Figure 3. Star Topology
Figure 4. Daisychain Topology
Figure 5. Hybrid Topology
Activity LEDs
The NI-9469 has four front panel LEDs labeled Trig 0, Trig 1, Trig 2, and Trig 3/Clk.
The LEDs blink when activity is detected on the corresponding line to or from the
carrier.
ni.com
8
NI-9469 Getting Started

Sleep Mode
This module supports a low-power sleep mode. Support for sleep mode at the
system level depends on the chassis the module is plugged into. Refer to the chassis
manual for information about support for sleep mode. If the chassis supports sleep
mode, refer to the soware help for information about enabling sleep mode. Visit
ni.com/info and enter cseriesdoc for information about C Series documentation.
Typically, when a system is in sleep mode, you cannot communicate with the
modules. In sleep mode, the system consumes minimal power and may dissipate
less heat than it does in normal mode. Refer to the Specifications section for more
information about power consumption and thermal dissipation.
Notice that when the NI 9469 is in sleep mode, the clock generation settings (if used)
must be reconfigured when the module exits sleep mode and power is restored.
NI-9469 Specifications
The following specifications are typical for the range -40 °C to 70 °C unless otherwise
noted.
I/O Characteristics
Front panel connectors Shielded RJ45 receptacle
Front panel indicators 4 green LEDs
Number of ports 3 (Port 0, 1, and 2)
Number of input/output signals 4 (Line 0, 1, 2, and 3) per port, 12 total
Signal type Dierential
Maximum simultaneous outputs 8
Number of I/O triggers to backplane 4 (Trig 0, 1, 2, and 3)
Clock generation (DDS)
Frequency 12.8 MHz or 13.1072 MHz
Accuracy ±3.5 ppm typical
© National Instruments 9
NI-9469 Getting Started

Cable
Type[1] CAT 5e (Shielded Twisted Pair) (straight-through)
Maximum propagation delay[2] 4.98 ns/m
Maximum length 100 m
1 Refer to the I/O Characteristics section for more information.
2 As specified for CAT 5e in TIA/EIA-568 Standard.
Power Requirements
Power consumption from chassis
Active mode 1 W maximum
Sleep mode 25 µW
Thermal dissipation (at 70 °C)
Active mode 1 W maximum
Sleep mode 25 µW
Physical Characteristics
Dimensions Visit ni.com/dimensions and search by module number.
Weight 148 g (5.2 oz)
Safety Voltages
Isolation
Channel-to-channel None
Channel-to-earth ground None
ni.com
10
NI-9469 Getting Started

Safety Compliance and Hazardous Locations Standards
This product is designed to meet the requirements of the following electrical
equipment safety standards for measurement, control, and laboratory use:
■IEC 61010-1, EN 61010-1
■UL 61010-1, CSA C22.2 No. 61010-1
■EN 60079-0, EN 60079-7
■IEC 60079-0, IEC 60079-7
■UL 60079-0, UL 60079-7
■CSA C22.2 No. 60079-0, CSA C22.2 No. 60079-7
Note For safety certifications, refer to the product label or the Product
Certifications and Declarations section.
Hazardous Locations
U.S. (UL) ; ,
Canada (C-UL) ; ,
Europe (DEMKO)
Electromagnetic Compatibility
CE Compliance
■2014/34/EU; Potentially Explosive Atmospheres (ATEX)
Product Certifications and Declarations
Refer to the product Declaration of Conformity (DoC) for additional regulatory
compliance information. To obtain product certifications and the DoC for NI
© National Instruments 11
NI-9469 Getting Started

products, visit ni.com/product-certifications, search by model number, and click the
appropriate link.
Shock and Vibration
To meet these specifications, you must panel mount the system.
Operating vibration
Random 5 g RMS, 10 Hz to 500 Hz
Sinusoidal 5 g, 10 Hz to 500 Hz
Operating shock 30 g, 11 ms half sine; 50 g, 3 ms half sine; 18 shocks at 6 orientations
Environmental
Refer to the manual for the chassis you are using for more information about
meeting these specifications.
Operating temperature (IEC 60068-2-1, IEC 60068-2-2) -40 °C to 70 °C
Storage temperature (IEC 60068-2-1, IEC 60068-2-2) -40 °C to 85 °C
Ingress protection IP40
Operating humidity (IEC 60068-2-30) 10% RH to 90% RH, noncondensing
Storage humidity (IEC 60068-2-30) 5% RH to 95% RH, noncondensing
Pollution Degree 2
Maximum altitude 2,000 m
Indoor use only.
Environmental Management
NI is committed to designing and manufacturing products in an environmentally
responsible manner. NI recognizes that eliminating certain hazardous substances
from our products is beneficial to the environment and to NI customers.
For additional environmental information, refer to the Engineering a Healthy
Planet web page at ni.com/environment. This page contains the environmental
ni.com
12
NI-9469 Getting Started

regulations and directives with which NI complies, as well as other environmental
information not included in this document.
EU and UK Customers
• Waste Electrical and Electronic Equipment (WEEE)—At the end of the product life
cycle, all NI products must be disposed of according to local laws and regulations.
For more information about how to recycle NI products in your region, visit ni.com/
environment/weee.
电子信息产品污染控制管理办法（中国 RoHS）
•
540
e
中国 RoHS— NI 符合中国电子信息产品中限制使用某些有害物质指令
(RoHS)。关于 NI 中国 RoHS 合规性信息，请登录 ni.com/environment/
rohs_china。(For information about China RoHS compliance, go to ni.com/
environment/rohs_china.)
NI Services
Visit ni.com/support to find support resources including documentation,
downloads, and troubleshooting and application development self-help such as
tutorials and examples.
Visit ni.com/services to learn about NI service oerings such as calibration options,
repair, and replacement.
Visit ni.com/register to register your NI product. Product registration facilitates
technical support and ensures that you receive important information updates from
NI.
NI corporate headquarters is located at 11500 N Mopac Expwy, Austin, TX,
78759-3504, USA.
© National Instruments 13
NI-9469 Getting Started
© 2022 National Instruments Corporation.