Nature's Cooling Solutions EcoBreeze 2. 2 User manual

877-565-1457 1
EcoBreeze 2. 2
Important Instructions –Installation and Operating
Manual
A product by Nature’s Cooling Solutions®
•When spring, summer and fall tend to be warm during the day and
cooler in the evenings and nighttime, use EcoBreeze 2.2 to cool
your home naturally with healthy filtered air. This Smart Window
Fan Constantly monitors indoor and outdoor conditions and
provides fresh clean outdoor air cooling whenever it is available
and needed. When it’s not available it seals up, keeping the hot
air outside and allows a seamless handoff to an AC. Just set the
EcoBreeze 2.2 set point below your AC set point.
For Additional Help:
Installing EcoBreeze 2 video: NaturesCoolingSolutions.com on EcoBreeze 2 tab
Call us at 877-565-1457 or email us at [e-mail]
Owner’s Manual Contents
Page
Important Safety Instructions
2
Parts List
3
Installation Double Hung Windows
4
Installation Slider Windows
5
Operating Instructions
6
Trouble Shooting
8
Maintenance Instructions/Warranty Information
8
Mother Nature provides the cool fresh air, we provide the technology!
EcoBreeze 2.2 Window Fan
Models: EB2-H08, EB2-H13, EB2-VR08, EB2-VR13, EB2-VL08, EB2-VL13,
This fan is for residential use only. It is not intended to be used in commercial, industrial or agricultural
settings.
READ AND SAVE THESE INSTRUCTIONS
READ CAREFULLY BEFORE ATTEMPTING TO ASSEMBLE, INSTALL, OPERATE, OR MAINTAIN THE PRODUCT.
PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY INFORMATION. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE. KEEP INSTRUCTIONS FOR
FUTURE REFERENCE.

877-565-1457 2
Important Safety Instructions
DANGER, ELECTRICAL, SHOCK, FIRE
GENERAL SAFETY INFORMATION
Read all instructions before using this fan.
1. Make certain the power source conforms to the electrical requirement of the fan.
2. Make sure the room is equipped with a working smoke detector.
3. Use this fan only as described in this manual. Any other use not recommended by the manufacturer may cause
fire, electrical shock, or injury to persons.
4. To reduce the risk of personal injury and electric shock, the fan should not be played with or placed where small
children can reach it. Close supervision is necessary when any appliance is used by or near children or disabled
people.
5. Unplug the power cord before installing, servicing, or moving the fan.
DO NOT DEPEND ON THE ON/OFF SWITCH AS THE SOLE MEANS DISCONNECTING
POWER WHEN SERVICING OR MOVING THE FAN.
6. This fan must NOT be used in potentially dangerous locations such as flammable, explosive, chemical-laden
atmospheres. To protect against electrical shock do not immerse the unit, plug, or cord in water or spray with
liquids.
7. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electrical shock,
this plug is intended to fit in a polarized outlet only one way. Match the wide blade of the plug to the wide slot.
Fully insert. If the plug does not fit in the outlet contact a qualified electrician. Do not attempt to defeat this
safety feature.
8. This product employs overload protection (fuse). A blown fuse indicates and overload or short-circuit situation.
If the fuse blows, unplug the product from the outlet. To replace the fuse open the fuse cover, remove the fuse
and replace with a new fuse (follow product marking for proper fuse rating) and check the product. If the
replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an
authorized service facility for examination and/or repair.
This plug is a safety feature. It contains a safety device (fuse) that should not be removed. Discard product if
the attachment plug is damaged. To reduce the risk of fire, electric shock and personal injury, DO NOT remove,
replace, repair, or tamper with the originally supplied plug. If the fan does not function properly, it may be due
to the safety device incorporated in this plug. If the plug warning label is missing or damaged, call (877) 565-
1457 Monday through Friday 8 am -5 pm central.
9. Where possible, avoid the use of extension cords because an extension cord may overheat and cause fire. If you

877-565-1457 3
must use an extension cord, minimize the risk of overheating by using the shortest cord possible and ensuring it
is UL listed. NEVER use a single extension cord to operate more than one fan. DO NOT plug fan into any other
cord connected device such as a power strip, core reel, surge protector, multiple outlet adapters or outlet type
air fresheners. The use of such devices may create a fire hazard.
10. NEVER operate any fan with a damaged cord or plug or after the fan malfunctions, has been dropped or
damaged in any manner.
11. NEVER insert or allow fingers or foreign objects to enter any ventilation opening as it may cause electrical shock
or fire, or damage the fan. To reduce the risk of fire, DO NOT block or tamper with the fan in any manner while
it is in operation.
12. Locate the power cord so the fan or other objects are not resting on it. Do not run the cord under carpeting.
Do not cover the cord with throw rugs, runners, or similar coverings. Do not route the cord under furniture or
appliances. Arrange the cord away from traffic areas and where it will not be tripped over.
13. NEVER locate a fan where it may fall into a bathtub or other water container. NEVER use fan where flammable
liquids are stored.
14. DO NOT attempt to repair or adjust any electrical or mechanical functions on this unit. Doing so will void your
warranty. The inside of this contains no user serviceable parts. All servicing should be performed by qualified
personnel only.
15. This fan is not suitable for use in agricultural facilities including areas where livestock, poultry or other animals
are confined. Please refer to the National Electrical Code (NEC) Article 547-7 (2008), or applicable state or
16. local codes or standards relating to electrical requirements for Agricultural Buildings. THIS FAN DOES NOT
MEET THE REQUIREMENTS OF NEC ARTICLE 547-7 (2008).
17. This fan is not suitable for use in hazardous locations. Please refer to the National Electric Code (NEC) Article
500 or applicable state or local codes or standards relating to electrical requirements for Hazardous locations.
THIS FAN DOES NOT MEET THE REQUIREMENTS OF NEC ARTICLE 500(2008).
Parts List
Insulating Weather strip
(1) 52” weather strip 1” x 0.5” for bottom and sides of unit
(1) 42” weather strip for top of unit
(1) 34”Center Sash 2 ply insulation
(1) Wire tie (6”)
Double sided glue dots and support adhesive
Support Bracket
Side Extenders
Double hung window unit –2 slider extenders and 2 insulated foam panels (7” x 9”)
Vertical window unit –1 slider extender, 1 insulated panel (7” x 9”) and 3 insulated slot extenders
Tools Required
Scissors
Phillips head screw driver

877-565-1457 4
Installation instructions –Double hung window
Remove the window screen
The EcoBreeze 2.2 fan will extend beyond the window screen. Remove the window screen. The
unit will be sealed in the installation process. The unit also has a filter that will block insects and
bugs so a screen is not necessary with this unit.
Install the bottom and side weather strip
Place 4 glue squares on the bottom window sill where EcoBreeze 2.2 will be placed. Cut the 52”
weather strip to the window width. Attach the weather strip to the bottom window sill. Place 2
glue squares on each side of the window. Cut 2 pieces from the 52” weather strip the height of
the unit and install the weather strip.
Install the support bracket
Install the support bracket. Place it in the center of the window and snug it up until it is approximately level. Remove
from the window. Install one wide glue adhesive on the vertical windowsill face and the other on the vertical outside
wall face. Place the bracket in the window and press it in place. Screws (user provided) may be
used to secure the bracket to the sill and outside wall.
Install the extenders
Remove the 2 end screws from the window bracket. Loosen the center screw.
Insert the extenders into the window bracket and secure with the 2 end
screws. Tighten the middle screw. Note: for windows that are between 20” and 22” use only one
extender.
Install EcoBreeze 2.2 in the window
Place EcoBreeze 2.2 so it is centered in the window. Slide the extenders to the window frame and into
the window channel.
Install the extender foam panels
Measure the opening in the extender. With scissors cut the foam insulation
panel approximately 1/8” larger for a snug fit. Slide foam in slot.
Install the top weather strip
Place 2 glue squares on the top of the unit and 2 on the end of the extenders.
Cut the 42” weather strip to the window width. Attach the weather strip to the
unit.
Close the window
Close the window so the window frame is between the window bracket and the
motor dome. For a secure installation a window lock can be purchased at home
centers or hardware stores and installed on the window.
Install the center sash insulation
Cut the center sash insulation to the window width. Loop wire tie around insulation for easy removal.
Insert it in the gap between the top windowpane and the lower window frame with the stiff insulation
facing indoors. For some windows with a narrow opening the insulation may be need to be smaller.
Cut the insulation along the width on the softer insulation side using scissors and install.
Enjoy Nature’s summer cooling!

877-565-1457 5
Installation instructions –Slider window
Remove the window screen
This fan will extend beyond the window screen. Remove the window screen. The unit will be sealed in the installation
process. The unit also has a filter that will block insects and bugs so a screen is not necessary with this unit.
Install the bottom, and side weather strip
Place 2 glue squares on the bottom window side where EcoBreeze 2.2 will be placed. Cut the 52” weather strip to the
window width. Attach the weather strip to the bottom window sill. Place 4 glue squares on the frame side of the
window. Cut a piece from the 52” weather strip the height of the window and install the weather strip on the frame
side of the window.
Install the support bracket
Install the support bracket. Place it in the center of the window and snug it up until it is
approximately level. Remove from the window. Install one wide glue adhesive on the
vertical window sill face and the other on the vertical outside all face. Place the bracket
in the window and press it in place. Screws (user provided) may be used to secure the
bracket to the sill and outside wall.
Install the extender
Remove the upper screw from the window bracket. Loosen the center screw. Insert the extender
into the window bracket with the open slot on the top. Secure with the 2 end screws. Tighten the
middle screw.
Install the window side weather strip
Place 4 glue squares on the window where EcoBreeze 2.2 will be placed. Cut the 42” weather strip to the window
height. Attach the weather strip to the window.
Install EcoBreeze 2.2 in the window
Place EcoBreeze 2.2 on the windowsill. Close the window so the window frame is
between the window bracket and the motor dome. Slide the extender to the top
of the window frame and into the window channel. Add the 3” extenders as
required based on the height of the window.
Install the extender foam panel. Measure the opening in the adjustable
extender. With scissors cut the foam insulation panel approximately 1/8” larger for a snug fit. Slide foam in slot. Close
the window.
Install the center sash insulation
Cut the center sash insulation to the window height. Loop wire
tie around insulation for easy removal. Insert it in the gap
between the top window pane and the lower window frame with
the stiff insulation facing indoors. For some windows with a
narrow opening the insulation may be need to be smaller. Cut the insulation on
the softer insulation using scissors.
Enjoy Nature’s summer cooling!

877-565-1457 6
Operating Instructions –Note: All buttons will allow 10 seconds to change a setting. The unit will
revert back to the run operation when it does not sense any additional input for 10 seconds.
EcoBreeze2 controls are designed to optimize the efficiency of cooling with outside air
1. On/off button
2. Fan mode button
3. Humidity control button
4. + Increase button
5. –Decrease button
6. Set up button
Power
Plug the unit into a 120 volt outlet. Press the on/off button to turn the unit on and off.
Set desired indoor temperature
Use the +/- to raise or lower the desired indoor temperature set point. The first push will show the current set point
temperature. Additional push raise or lower the temperature. After 10 seconds it will show the room temperature. A
lower set point will increase the use of outside air and can precool the home delaying the need for air conditioning.
Set humidity on/off
EcoBreeze 2.2 has a humidity lock out feature that increases energy efficiency and comfort when the unit is being used
with air conditioning. Push the HUM button and the Hum Limit light will illuminate indicating the limit is on. The control
is adjustable for different climate zones and individual preference. Use +/- to adjust. 1 is the lowest setting for dryer
climates and 6 is the highest setting for humid climates. In this mode the unit continuously monitors indoor and
outdoor humidity and will not bring in humid outside air. If the outdoor humidity is too high the Outdoor Humidity will
be illuminated. When air conditioning is not used the control can be turned off and the Hum display light will turn off.
Please note EcoBreeze 2.2 measures dew point not relative humidity.
Select the fan mode
The fan button changes the fan mode. . Press the fan button to toggle through the fan modes. The first press shows the
current mode. O for manual ON, 1 for automatic low speed, and 2 for automatic high or turbo speed.
Automatic mode
This unit has two automatic modes, automatic low speed and automatic high speed. Automatic low will not increase the
fan speed above a desired maximum. Automatic low speed can be adjusted in the set up mode and is useful to limit the
fan speed and noise especially at night. Automatic high speed is good to use when maximum cooling is needed such as
cooling a bedroom in the early evening or in the morning to capture the full benefits of precooling a room to reduce the
need for AC during the day.
Manual speed mode
The fan will run continuously on this setting. Press the fan button to 0 and immediately press the +/- buttons to raise or
lower the fan speed. Note the display will continue to display O for on when the fan is in manual mode. Press the fan
button once to adjust the speed when it is already in this mode.
Change the filter
The filter should be changed regularly to maximize cleaning effectiveness. The filter reminder can be adjusted based on
the conditions in the area. If the filter is clogged go to the setup and reduce the hours between filter changes. If the
filter is clean increase the hours between filters changes. The filter drawer is at the bottom of the unit. It may be

877-565-1457 7
opened with the handle on the bottom or the two finger tabs on the side of the unit. Slide the drawer completely out of
the unit. Slide the cover back to access the filter. Remove the existing filter and replace with a new filter. The filter
dimensions are a nominal 12” x 12” x 1” and may be purchased from Nature’s Cooling Solutions. The filter has a
direction indicator for the airflow direction. The filter should be installed so the airflow goes toward the top of the filter
drawer. Replace the filter drawer for operation.
Set up and customization
EcoBreeze 2.2 can be customized for different conditions or user preferences.
The standard settings for EcoBreeze 2.2 are:
Auto low Fan Speed –6
Display Light setting - High
Filter change –500 hours
Temperature scale –Fahrenheit
The settings can be changed by pressing the setup button. It will revert back to the run operation when it does not
sense any additional input for 10 seconds.
First press of button –Displays thousands and hundreds of hours of fan run time
Second press of set button - Displays tens and single digit of hours of fan run time. The unit only has 2 positions on the
display so combining the first and second display would give lifetime run hours. I.e. 01, 95 would be 0195 hours of fan
run time. This will provide information on actual hours of natural cooling that the fan is providing. (Like a car odometer)
Third press of the set button –Displays the outdoor temperature
Fourth press of the set button –Displays the indoor humidity dew point temperature
Fifth press of the set button –Displays the outdoor humidity dew point temperature
Sixth press of the set button –This will customize the Maximum fan speed for the low auto mode (1). The lower fan
setting will limit the fan speed in the quiet mode. The settings are 1-10. Press + or –to raise or lower the maximum
speed based on your preference.
Seventh press –Customize display light level for your preferences.
0 –Off - in this mode the display will be off unless a button is pressed. When any button is pushed the display
will illuminate for 30 seconds and they return to the off mode.
1 –Dim
2 –Medium
3 –Maximum
Eighth press of set button –displays the hours remaining until the filter needs to be changed. Press +/- to reset to the
maximum hours
Ninth press of the set button –Filter change. Customize the hour of run time between filter changes. The hours are
the display times 10. A display of 50 represents a setting of hours. This is preset at 500 hours. For an area with a high
level of outdoor pollution decrease the hours between changes. For areas with a low level of outdoor pollution increase
the hours. Press + or –to raise or lower the hours.
Tenth press of the set button –Select temperature scale. Press + or –to toggle between Fahrenheit and Centigrade.
Push set Display Push set Display Change +/-
1st Hours of run time - thousands & hundreds
2nd Hours of run time –tens and single digits
3rd Outdoor Temperature
4th Indoor dew point
5th Outdoor dew point
6th Auto low Maximum fan speed - 1 low, 10 high
7th Light level 0 off, 1 dim, 3 bright
8th Filter Hours Remaining +/-reset to max
9th Max Filter hours (x10) 10 to 100
10th Temperature scale F or C

877-565-1457 8
Trouble shooting
EcoBreeze 2.2 not running
In auto mode EcoBreeze 2.2 will stay on or off for a
minimum of 3 minutes. This prevents short cycling.
Wait 3 minutes to confirm the fan is not running.
Confirm set point is less than indoor temperature.
If outdoor temp is illuminated outdoor temperature is
greater than indoor temperature and the fan will not
run.
If outdoor humidity light is on, the outdoor humidity is
above the set point and it is too humid for cooling. The
fan will not bring in humid air. This only works when
the humidity lock is on.
Check temperature and humidity readings.
Indoor temperature is displayed when no changes are
being made. The rest of the temperature and humidity
values can be displayed by pressing the settings button.
See the set up sequence on page 7.
Air flow decreases
If air flow decreases check the filter. If the filter is dirty
replace it and adjust filter reminder to a lower setting.
1 Year Limited Warranty
Nature’s Cooling Solutions (NCS) warrants that for a period of one year from the date of purchase, this product will be free from
defects in material and workmanship. NCS, at its option, will repair or replace this product or any component of the product found
to be defective during the warranty period. Replacement will be made with a new or remanufactured product or component. If the
product is no longer available, replacement may be made with a similar product of equal or greater value. This is your exclusive
warranty. Do NOT attempt to repair or adjust any electrical or mechanical functions on this product. Doing so will void this warranty.
This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable. Keep the original
sales receipt. Proof of purchase is required to obtain warranty performance. This warranty does not cover normal wear of parts or
damage resulting from any of the following: negligent use or misuse of the product, use on improper voltage or current, and use
contrary to the operating instructions, disassembly, repair or alteration by anyone other than NCS or an authorized NCS service
center. Further, the warranty does not cover: Acts of God, such as fire, flood, hurricanes and tornadoes. What are the limits on NCS’s
Liability? NCS shall not be liable for any incidental or consequential damages caused by the breach of any express, implied or
statutory warranty or condition. Except to the extent prohibited by applicable law, any implied warranty or condition of
merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty. NCS disclaims all
other warranties, conditions or representations, express, implied, statutory or otherwise. JCS shall not be liable for any damages of
any kind resulting from the purchase, use or misuse of, or inability to use the product including incidental, special, consequential or
similar damages or loss of profits, or for any breach of contract, fundamental or otherwise, or for any claim brought against
purchaser by any other party. Some provinces, states or jurisdictions do not allow the exclusion or limitation of incidental or
consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusion may not apply to
you. This warranty gives you specific legal rights, and you may also have other rights that vary from province to province, state to
state or jurisdiction to jurisdiction. How to Obtain Warranty Service in the U.S.A. If you have any questions regarding this warranty or
would like to obtain warranty service, please call 1-877-565-1457 or direct your correspondences to ATTN: Nature’s Cooling
Solutions, Customer Service, 4881 N Calle Bujia, Tucson, AZ 85718.
Revised April 2021