NEC MultiSync FE750 JC-17W40 User manual

English
0
5
25
75
95
100

0
5
25
75
95
100

Contents
FE Series monitor box* should contain the following:
• MultiSync FE Series Monitor with tilt/swivel base
MultiSync FE750 (JC-17W40) or
MultiSync FE950 (JC-19W40) or
MultiSync FE1250 (JC-22W71)
• Power Cord
• Captive Signal Cable
• User’s Manual
* Remember to save your original box and packing material to transport
or ship the monitor.
Power Cord
User's Manual
Captive Signal
Cable
E-1
0
5
25
75
95
100

Quick Start
To attach the MultiSync FE Series monitor to your system,
follow these instructions:
1. Turn off the power to your computer and MultiSync monitor.
2. If necessary, install the display card. For more information, refer to the
display card manual.
3. For the PC: Connect the 15-pin mini D-SUB of the captive signal cable
to the connector of the display card in your system (Figure A.1).
Tighten all screws.
For the Mac: Connect the Macintosh Cable Adapter (not included) to the
monitor connector on the Macintosh (Figure B.1). Attach the 15-pin mini
D-SUB end of the captive signal cable to the Macintosh cable adapter on
the computer (Figure B.1). Tighten all screws.
Computer
Captive Signal
Cable
Mac Adapter
(not included)
Figure B.1
Computer
15-pin mini
D-SUB
Captive Signal
Cable
Figure A.1
E-2
0
5
25
75
95
100

4. Connect one end of the power
cord to the monitor and the
other end to the power outlet
(Figure C.1).
5. Turn on the monitor (Figure D.1) and the computer.
6. This completes the installation.
NOTE: If you have any problems, please refer to the Troubleshooting
section of this User's Manual.
Power Outlet
Power
Cord
Figure C.1
Power Button
Figure D.1
E-3
0
5
25
75
95
100

Controls
OSM (On-Screen Manager) control buttons on the front of
the monitor function as follows:
Main Menu Sub-Menu
EXIT Exits the OSM menu. Exits to the OSM main menu.
CONTROL
▲/▼Moves the highlighted area
up/down to select one of the
controls.
Moves the highlighted area
up/down to select one of the
controls.
CONTROL
-/+
Moves highlighted area
left/right to select one of the
controls.
Moves the bar in the - or +
direction to decrease or
increase the adjustment.
PROCEED Has no function . Only executes control or enters
sub, sub-menu.
RESET Resets all the controls within
the highlighted menu to the
factory setting.
Resets the highlighted control
to the factory setting.
NOTE: When RESET is pressed in the main and sub-menu, a warning
window will appear allowing you to cancel the reset function.
When OSM controls are activated, icons are displayed at the top of the
menu. If an arrow (→) is displayed in a sub-menu, it indicates further
choices are available. To enter a sub, sub-menu, press PROCEED.
ab Brightness/Contrast Controls
BRIGHTNESS: Adjusts the overall image and background screen brightness.
CONTRAST: Adjusts the image brightness in relation to the background.
DEGAUSS: Eliminates the build-up of stray magnetic fields which alter
the correct scan of the electron beams and affect the purity of the screen
colours, focus, and convergence. When activated, your screen image will
jump and waver a bit as the screen is demagnetized.
Caution: Please allow a minimum of 20 minutes to elapse between uses
of the Degauss function.
de Size and Position Controls
AUTO ADJUST: Automatically adjusts the horizontal and vertical size and
position settings for applicable signal timings.
LEFT/RIGHT: Moves the image horizontally (left or right).
DOWN/UP: Moves the image vertically (up or down).
NARROW/WIDE: Decreases or increases the horizontal size of the image.
SHORT/TALL: Decreases or increases the vertical size of the image.
E-4
0
5
25
75
95
100

xColor Control
Color Presets 1 through 5, selects the desired color setting. The bar is
replaced by the color setting choice from 1 to 5. Each color setting is
adjusted at the factory to the stated Kelvin. If a setting is adjusted, the
name of the setting will change from Kelvin to Custom.
RED, GREEN, BLUE: Decreases or increases red, green, or blue
depending upon which is selected. The change in color will appear on
screen and the direction (decrease or increase) will be shown by the bars.
pq Geometry Controls
The Geometry controls allow you to adjust the curvature or angle of the
sides of your display.
IN/OUT (pincushion): Decreases or increases the curvature of the sides
either inward or outward.
LEFT/RIGHT (pincushion balance): Decreases or increases the
curvature of the sides either to the left or right.
TILT (parallelogram): Decreases or increases the tilt of the sides either
to the left or right.
ALIGN (trapezoidal): Decreases or increases the bottom of the screen
to be the same as the top.
ROTATE (raster rotation): Rotates the entire display clockwise or
counter clockwise.
?Tools 1
MOIRÉ CANCELER: Moiré is a wavy pattern which can sometimes appear
on the screen. The pattern is repetitive and superimposed as rippled
images. When running certain applications, the wavy pattern is more
evident than in others. To reduce moiré, adjust the ON/Level by using the
–/+ CONTROL buttons.
BASIC CONVERGENCE: Aligns all three colors (R, G, B) to form a single
color (white). The purpose of this control is to ensure that a white line
drawn on the screen is as crisp and clear as possible.
• Use the Horizontal control to adjust the alignment of the white lines in
the up/down direction.
• Use the Vertical control to adjust the alignment of the white lines in the
left/right direction.
E-5
0
5
25
75
95
100

AREA CONVERGENCE: A small window will appear to indicate the area
of adjustment — Top Horizontal, Top Vertical, Bottom Horizontal or
Bottom Vertical.
CORNER CORRECTION: Allows you to adjust the geometry of the corners
of your display — Top, Top Balance, Bottom or Bottom Balance.
LINEARITY: The Linearity selection allows you to adjust the spacing of the
areas on the screen. The purpose of this control is to ensure that a 2 cm
circle is a true 2 cm circle wherever it is drawn on the screen. The best
way to determine the vertical linearity is as follows:
• Draw equally spaced horizontal lines using a drawing application that
has a ruler.
• Use the Vertical Balance control to adjust the lines near the top and
bottom of your screen.
• Use the Vertical control to adjust the spacing between the lines near
the centre and top of your screen.
GLOBALSYNC CONTROL (MultiSync FE950 and MultiSync FE1250 only):
Eliminates picture impurities that may result from the earth’s magnetic
field. While in the sub-menus (TOP LEFT, TOP RIGHT, BOTTOM LEFT or
BOTTOM RIGHT), use the –/+ control buttons to fine tune the GlobalSync
corrections.
Note: NEC recommends that you perform GlobalSync correction while
running a typical application such as a spreadsheet or text
document.
FACTORY PRESET: Selecting Factory Preset allows you to reset most OSM
settings back to the factory settings. A warning statement will appear to
confirm that you do want to reset ALL settings. Individual settings can be
reset by highlighting the control to be reset and pressing the RESET button.
?Tools 2
LANGUAGE: OSM menus are available in 7 languages.
OSM TURN OFF: The OSM menu will stay on as long as it is in use. In
the OSM Turn Off sub-menu, you can select how long the monitor waits
after the last touch of a button to shut off the OSM menu. The preset
choices are 10, 20, 30, 60, 120 seconds.
E-6
0
5
25
75
95
100

OSM LOCK OUT: This control completely locks out access to all OSM
functions except brightness and contrast controls. When attempting to
activate OSM while in the lockout mode, a screen will appear indicating
that OSM controls are locked out. To activate the OSM Lockout function,
press PROCEED, then press “▲” and hold down simultaneously. To
de-activate the OSM Lockout, press PROCEED, then press “▲” and hold
down simultaneously.
IPM System Off Mode:
ENABLE: The IPM works normally, all stages
of the energy saving are used.
DISABLE: The OFF MODE of the IPM is not
used.
NOTE: For standard computers and display cards you should keep
the factory setting ENABLE.
EDGELOCK CONTROL: Operating your monitor at a non-standard
timing may cause images to appear darker than normal or have color
distortion. Use of the EdgeLock control will adjust images to their normal
state.
REFRESH NOTIFIER: A message will advise you if the refresh rate of the
signal being applied to the monitor by the computer is too low. For
further information, please refer to your display card or system manual.
Factory setting is OFF.
zInformation
Provides you with additional information which includes the following:
DISPLAY MODE: Indicates the current mode and frequency setting of the
monitor.
MONITOR INFO: Indicates the model number and the serial number.
E-7
0
5
25
75
95
100

Recommended use
Safety Precautions and Maintenance
FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE
FOLLOWING WHEN SETTING UP AND USING
THE MULTISYNC FE SERIES COLOR MONITOR:
•DO NOT OPEN THE MONITOR. There are no user serviceable parts
inside and opening or removing covers may expose you to dangerous
shock hazards or other risks. Refer all servicing to qualified service
personnel.
• Use the monitor in a clean, dry area.
• Do not spill any liquids into the cabinet or use your monitor near water.
• Do not insert objects of any kind into the cabinet slots, as they may
touch dangerous voltage points, which can be harmful or fatal or may
cause electric shock, fire or equipment failure.
• Do not place any heavy objects on the power cord. Damage to the cord
may cause shock or fire.
• Do not place this product on a sloping or unstable cart, stand or table,
as the monitor may fall, causing serious damage to the monitor.
• Keep the monitor away from high capacity transformers, electric motors
and other devices such as external speakers or fans, which may create
strong magnetic fields.
• If possible, position the monitor so that it is facing the east to minimize
the effects of the earth’s magnetic field.
• Changing the direction of the monitor while it is powered on may cause
image discoloration. To correct this, turn the monitor off for 20 minutes
before powering it back on.
• To separate the equipment from the power source you have to remove
the plug from the inlet socket.
• When operating the MultiSync monitor with its AC 220-240V worldwide
power supply, use a power supply cord that matches the power supply
voltage of the AC power outlet being used. The power supply cord you use
must have been approved by and comply with the safety standards of your
country. (Type H05VV-F should be used except in UK)
• In UK, use a BS-approved power cord with molded plug having a black
(5A) fuse installed for use with this monitor. If a power cord is not
supplied with this monitor, please contact your supplier.
Immediately unplug your monitor from the wall outlet and refer servicing
to qualified service personnel under the following conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled, or objects have fallen into the monitor.
E-8
0
5
25
75
95
100

• If the monitor has been exposed to rain or water.
• If the monitor has been dropped or the cabinet damaged.
• If the monitor does not operate normally by following operating
instructions.
• Allow adequate ventilation around the monitor so that
heat can properly dissipate. Do not block ventilated
openings or place the monitor near a radiator or other
heat sources. Do not put anything on top of monitor.
• The power cable connector is the primary means of
detaching the system from the power supply. The
monitor should be installed close to a power outlet
which is easily accessible.
• Handle with care when transporting. Save packaging
for transporting.
CORRECT PLACEMENT AND ADJUSTMENT OF THE
MONITOR CAN REDUCE EYE, SHOULDER AND NECK
FATIGUE. CHECK THE FOLLOWING WHEN YOU
POSITION THE MONITOR:
• Adjust the monitor height so that the
top of the screen is at or slightly
below eye level. Your eyes should
look slightly downward when
viewing the middle of the screen.
• Position your monitor no closer than
40 cm and no further away than
70 cm from your eyes. The optimal
distance is 60 cm.
• Rest your eyes periodically by
focusing on an object at least 6 m
away. Blink often.
• Position the monitor at a 90° angle
to windows and other light sources to minimize glare and reflections.
Adjust the monitor tilt so that ceiling lights do not reflect on your screen.
• If reflected light makes it hard for you to see your screen, use an
anti-glare filter.
• Clean your monitor regularly. Use a lint-free, non-abrasive cloth and a
non-alcohol, neutral, non-abrasive cleaning solution or glass cleaner to
minimize dust.
CAUTION
E-9
0
5
25
75
95
100

• Adjust the monitor’s brightness and contrast controls to enhance
readability.
• Use a document holder placed close to the screen.
• Position whatever you are looking at most of the time (the screen or
reference material) directly in front of you to minimize turning your
head while you are typing.
• Get regular eye checkups.
Ergonomics
To realize the maximum ergonomics benefits, we recommend the
following:
• Adjust the Brightness until the background raster disappears
• Do not position the Contrast controls to its maximum setting
• Use the preset Size and Position controls with standard signals
• Use the preset Color Setting and Sides Left/Right controls
• Use non-interlaced signals with a vertical refresh rate between
75-160 Hz
• Do not use primary color blue on a dark background, as it is difficult to
see and may produce eye fatigue due to insufficient contrast
E - 10
0
5
25
75
95
100

Specifications
Monitor
Specifications MultiSync FE750 Monitor Notes
Picture Tube Diagonal:
Viewable Image Size:
Radius:
43 cm (17 inch)
41 cm (16 inch)
50000 mm
90° deflection, 0.25 mm grille pitch, medium short
persistence phosphor, aperture grille CRT,
multi-layered, anti-static screen coating, dark tint
screen and OptiClear screen surface.
Input Signal Video:
Sync:
ANALOG 0.7 Vp-p/75 Ω
Separate sync. TTL Level
Horizontal sync. Positive/Negative
Vertical sync. Positive/Negative
Composite sync. (Positive/Negative) (TTL Level)
Display Colors Analog input: Unlimited number of Colors Depends on the display card
Synchronization
Range
Horizontal:
Vertical:
31 kHz to 92 kHz
55 Hz to 160 Hz
Automatically
Automatically
Resolutions Supported
Resolution based on horizontal and vertical
frequencies only
640 x 480 @60 to 160 Hz
800 x 600 @55 to 141 Hz
832 x 624 @55 to 136 Hz
1024 x 768 @55to112Hz..................
1152 x 870 @55 to 99 Hz
1280 x 1024 @55 to 85 Hz
1600 x 1200 @55 to 73 Hz
Some systems may not support all modes listed
NEC cites recommended resolution at 85 Hz for
optimal display performance.
Active Display Area
(Factory setting)
Horizontal:
Vertical:
315 mm
236 mm
Dependent upon signal timing used, and does not
include border area.
Active Display Area
(Full scan)
325 mm
243 mm
Dependent upon signal timing used, and does not
include border area.
Power Supply AC 100-120 V / 220-240 V, 50/60 Hz
Current Rating 1.1 A @100-120 V / 0.5 A @220-240 V
Dimensions 403 (W) x 427 (H) x 424 (D) mm
Weight 20.0 kg
Enviromental Considerations
Operating Temperature:
Humidity:
Altitude:
Storrage Temperature:
Humidity:
Altitude:
+10°C to +35°C
30% to 80%
0 to 3000 m
-20°C to +60°C
10% to 90%
0 to 13700 m
NOTE: Technical specifications are subject to change without notice.
E - 11
0
5
25
75
95
100

Monitor
Specifications MultiSync FE950 Monitor Notes
Picture Tube Diagonal:
Viewable Image Size:
Radius:
49.5 cm (19 inch)
45.8 cm (18 inch)
57800 mm
90° deflection, 0.25-0.27 mm (variable) grille pitch,
medium short persistence phosphor, aperture grille
CRT, multi-layered, anti-static screen coating,
semi-dark tint screen, and OptiClear screen surface.
Input Signal Video:
Sync:
ANALOG 0.7 Vp-p/75 Ω
Separate sync. TTL Level
Horizontal sync. Positive/Negative
Vertical sync. Positive/Negative
Composite sync. (Positive/Negative) (TTL Level)
Display Colors Analog input: Unlimited number of Colors Depends on the display card
Synchronization
Range
Horizontal:
Vertical:
31 kHz to 96 kHz
55 Hz to 160 Hz
Automatically
Automatically
Resolutions Supported
Resolution based on horizontal and vertical
frequencies only
640 x 480 @60 to 160 Hz
800 x 600 @55 to 152 Hz
832 x 624 @55 to 146 Hz
1024 x 768 @55 to 119 Hz
1152 x 870 @55 to 104 Hz
1280 x 1024 @55to89Hz..................
1600 x 1200 @55 to 76 Hz
1792 x 1344 @55 to 68 Hz
Some systems may not support all modes listed
NEC cites recommended resolution at 85 Hz for
optimal display performance.
Active Display Area
(Factory setting)
Horizontal:
Vertical:
356 mm
267 mm
Dependent upon signal timing used, and does not
include border area.
Active Display Area
(Full scan)
366 mm
275 mm
Dependent upon signal timing used, and does not
include border area.
Power Supply AC 100-120 V / 220-240 V, 50/60 Hz
Current Rating 1.2 A @100-120 V / 0.6 A @220-240 V
Dimensions 442 (W) x 456 (H) x 447 (D) mm
Weight 24.3 kg
Enviromental Considerations
Operating Temperature:
Humidity:
Altitude:
Storrage Temperature:
Humidity:
Altitude:
+10°C to +35°C
30% to 80%
0 to 3000 m
-20°C to +60°C
10% to 90%
0 to 13700 m
NOTE: Technical specifications are subject to change without notice.
E - 12
0
5
25
75
95
100

Monitor
Specifications MultiSync FE1250 Monitor Notes
Picture Tube Diagonal:
Viewable Image Size:
Radius:
55.3 cm (22 inch)
50.8 cm (20 inch)
57800 mm
90° deflection, 0.25-0.27 mm (variable) grille pitch,
medium short persistence phosphor, aperture grille
CRT, multi-layered, anti-static screen coating,
semi-dark tint screen, and OptiClear screen surface.
Input Signal Video:
Sync:
ANALOG 0.7 Vp-p/75 Ω
Separate sync. TTL Level
Horizontal sync. Positive/Negative
Vertical sync. Positive/Negative
Composite sync. (Positive/Negative) (TTL Level)
Display Colors Analog input: Unlimited number of Colors Depends on the display card
Synchronization
Range
Horizontal:
Vertical:
31 kHz to 110 kHz
55 Hz to 160 Hz
Automatically
Automatically
Resolutions Supported
Resolution based on horizontal and vertical
frequencies only
640 x 480 @60 to 160 Hz
800 x 600 @55 to 160 Hz
832 x 624 @55 to 160 Hz
1024 x 768 @55 to 136 Hz
1152 x 870 @55 to 120 Hz
1280 x 1024 @55 to 102 Hz
1600 x 1200 @55to88Hz..................
1792 x 1344 @55 to 78 Hz
1800 x 1440 @55 to 73 Hz
1856 x 1392 @55 to 75 Hz
1920 x 1440 @55 to 73 Hz
Some systems may not support all modes listed
NEC cites recommended resolution at 85 Hz for
optimal display performance.
Active Display Area
(Factory setting)
Horizontal:
Vertical:
396 mm
297 mm
Dependent upon signal timing used, and does not
include border area.
Active Display Area
(Full scan)
406 mm
305 mm
Dependent upon signal timing used, and does not
include border area.
Power Supply AC 100-120 V / 220-240 V, 50/60 Hz
Current Rating 1.4 A @100-120 V / 0.7 A @220-240 V
Dimensions 483 (W) x 501 (H) x 472 (D) mm
Weight 32.0 kg
Enviromental Considerations
Operating Temperature:
Humidity:
Altitude:
Storrage Temperature:
Humidity:
Altitude:
+10°C to +35°C
30% to 80%
0 to 3000 m
-20°C to +60°C
10% to 90%
0 to 13700 m
NOTE: Technical specifications are subject to change without notice.
E - 13
0
5
25
75
95
100

Features
Flat Aperture Grille CRT: Delivers an unparalleled viewing experience
with a virtually flat image, eliminating distortion and reducing glare so
that what you see on-screen is what you get on your printed output. The
striped phosphor alignment of the CRT delivers superior vertical definition
with improved brightness for more uniform image contrast.
OptiClear Screen Surface: Reduces reflection and glare and increases
contrast without sacrificing focus level, clarity or brightness.
Dual Dynamic Beam Focus: Provides precise, continuous focus
adjustment of the electron beams and optimum image quality, even to
the far edge of the screen.
Color Control System: Allows you to change between five color settings
on your display to match your personal preference.
OSM (On-Screen Manager) Controls: Allow you to quickly and easily
adjust all elements of your screen image via simple to use on-screen menus.
ErgoDesign Features: Enhance human ergonomics to improve the
working environment, protect the health of the user and save money and
is compliant with TCO'99 and MPRII for lower emissions.
Plug and Play: The Microsoft®solution with the Windows®95/98
operating system facilitates setup and installation by allowing the monitor
to send its capabilities (such as screen size and resolutions supported)
directly to your computer, automatically optimizing display performance.
IPM (Intelligent Power Manager) System: Provides innovative
power-saving methods that allow the monitor to shift to a lower power
consumption level when on but not in use, saving your monitor energy costs,
reducing emissions and lowering the air conditioning costs of the workplace
and is compliant with NUTEK, VESA DPMS and EPA ENERGY STAR.®
Mode LED Indicator Power Saving
On Green None
Stand By Green Minimum (Quickest Recovery)
Suspend Yellow Moderate (< 15 Watts, Moderate Recovery)
Off (IPM Mode) Orange Maximum (< 5 Watts, Slow Recovery)
Off (Power
Switch, Off) No Light No Power Used (Fully Off)
Reduced Magnetic Field Technology: Reduces magnetic and
alternating electric field emissions and static electricity, addressing
ergonomic concerns regarding potential risks from extended computer
monitor use and is compliant with TCO'99 and MPRII.
E - 14
0
5
25
75
95
100

Multiple Frequency Technology: Automatically adjusts monitor to the
display card’s scanning frequency, thus displaying the resolution required.
FullScan Capability: Allows you to use the entire screen area in most
resolutions, significantly expanding image size.
GlobalSync/Corner Purity Control (MultiSync FE950 and
MultiSync FE1250 only):NEC’s unique design eliminates picture
impurities that may result from stray magnetic fields (including the earth’s
permanent magnets, etc.) and now allows you to easily adjust impurities
in the four corners of your monitor.
Auto Adjust: Allows you to easily and quickly adjust the suitable
horizontal and vertical size and position settings.
Convergence Control: Allows you to adjust the horizontal and vertical
convergence of the top and bottom area to ensure that a white line
drawn on the screen is as crisp and clear as possible.
E - 15
0
5
25
75
95
100

Troubleshooting
No Picture
• The display card should be completely seated in its slot.
• Power Switch and computer power switch should be in the ON position.
• The signal cable should be completely connected to the display
card/computer.
• Check the connector for bent or pushed-in pins.
Image is scrolling or unstable
• Signal cable should be completely attached to the computer.
• Check the pin assignment and signal timing of your monitor and
display card with respect to the recommended timing and pin
assignment.
• If the Macintosh adapter is used, check for proper connection or make
sure the display card is Macintosh compatible and that the card is
properly seated in the computer.
LED on monitor is not lit (no green, orange or yellow color can be seen)
• Power Switch should be in the ON position and the power cord should
be connected.
Picture is fuzzy or color looks blotchy
• If the picture is fuzzy, adjust the Moire Canceler Control. If the color
looks blotchy, adjust the Brightness, Contrast or GlobalSync Controls,
or use the EdgeLock control to change modes.
• Access the Degauss Control through OSM. Activate the Degauss
Control.
CAUTION: A minimum interval of 20 minutes should exist before the
Degauss Function is used a second time.
Picture bounces or a waving pattern is present in the
picture
• Move electrical devices that may be causing electrical interference away
from the monitor.
Edges of the display image are not square
• Use the OSM Geometry Controls to straighten the edges.
• If possible, position the front of the monitor facing east.
E - 16
0
5
25
75
95
100

Display image is not centered, too smaIl, or too large
• Use the OSM Size and Position controls to adjust the image.
Thin lines appear on your screen
• Thin lines are normal for an aperture grille CRT and are not a
malfunction. These are shadows from the damper wires used to
stabilize the aperture grille and are most noticeable when the screen's
background is light (usually white).
E - 17
0
5
25
75
95
100

0
5
25
75
95
100