NEC PlasmaSync 60XC10 User manual

NEC Corporation of America
Visual Systems Division
P60XC10 Installation Guide
60” Plasma Display Rev 1.0
www.necvisualsystems.com P60XC10 Page 1 of 10
Contents:
Product Description and Notes Page 1
Ventilation Requirements Page 2
Display Dimensions
Front, Top, Bottom & Right Side Page 3
Rear Page 4
Display Dimensions w/Optional Speakers and Stand Page 5
Optional Stand Dimensions Page 6
Optional Speakers Dimensions Page 7
Connections Page 8
PC Control Page 9, 10
Product Description
Type: Plasma Display Screen Surface: Anti-Reflective
Resolution: 1366x768 Dimensions: 56.97”(W) x 34.48”(H) x 5.10”(D)
Aspect Ratio: 16:9 Weight: 154.3 lbs
FCC: ClassB
Notes
This document is intended to be used as a reference guide to supply useful information for a design or installation. It is not intended to
be a step-by step procedure for installation.
Any ceilings or walls must be strong enough to support the display and the installation must be in accordance with any local
building codes. All mounts should make secure contact to wood studs.
4:3 sources can be displayed on the 16:9 screen in either normal aspect ratio with bars on the left or right, or stretched horizontally to
fill the screen using the menus (see “Aspect Modes” in menus and user manual).
Distances are in inches, for millimeters multiply by 25.4.
Distances may vary ±5%.
Maximum Tilt Angles
Below are the maximum angles that the display can be tilted in both landscape and portrait mode
Landscape 20°
Portrait 20°

NEC Corporation of America
Visual Systems Division
P60XC10 Installation Guide
60” Plasma Display Rev 1.0
www.necvisualsystems.com P60XC10 Page 2 of 10
Ventilation Requirements (all models)
Dimensions below are minimum required for proper ventilation.
NOTE: The ventilation space should not be covered or closed off at the front of the opening. If for some reason the
opening needs to be covered, other means of ventilation will need to be incorporated into the design. Contact NEC for
design review and recommendations.
WALL
WALL
2
”
2
”
WALL
2
”
2
”
2
”

NEC Corporation of America
Visual Systems Division
P60XC10 Installation Guide
60” Plasma Display Rev 1.0
www.necvisualsystems.com P60XC10 Page 3 of 10
Display dimensions

NEC Corporation of America
Visual Systems Division
P60XC10 Installation Guide
60” Plasma Display Rev 1.0
www.necvisualsystems.com P60XC10 Page 4 of 10
Display dimensions (cont.)

NEC Corporation of America
Visual Systems Division
P60XC10 Installation Guide
60” Plasma Display Rev 1.0
www.necvisualsystems.com P60XC10 Page 5 of 10
Dimensions with optional speakers and stand

NEC Corporation of America
Visual Systems Division
P60XC10 Installation Guide
60” Plasma Display Rev 1.0
www.necvisualsystems.com P60XC10 Page 6 of 10
Optional Speakers and Stand Dimensions
Table Top Stand
ST-P60C1

NEC Corporation of America
Visual Systems Division
P60XC10 Installation Guide
60” Plasma Display Rev 1.0
www.necvisualsystems.com P60XC10 Page 7 of 10
Optional Speakers
SP-P60P1

NEC Corporation of America
Visual Systems Division
P60XC10 Installation Guide
60” Plasma Display Rev 1.0
www.necvisualsystems.com P60XC10 Page 8 of 10
Connections Located at Bottom of Display
Control Buttons

NEC Corporation of America
Visual Systems Division
P60XC10 Installation Guide
60” Plasma Display Rev 1.0
www.necvisualsystems.com P60XC10 Page 9 of 10
PC Control
1. Interface Standard Simple Special
Communication system Asynchronus Asynchronus Asynchronus
Protocol RS-232C RS-232C RS-232C
Baud rate 9600 bps 9600 bps 9600 bps
Data length 8 bits 8 bits 8 bits
Parity bit None None Odd
Stop bit 1 bit 1 bit 1 bit
Flow control None None None
Communication code ASCII ASCII Hex
2. Control command diagram
1) Standard Header Message Check Code Delimiter
2) StandardAddress code Function code Data code End code
3) Special Command1 Unit ID1 Unit ID2 Command2 Data length Data Check Sum
3. Command List
1
)
Standard
No Item
N
o
t
es
1 Power ON / OFF
2 Power Status
3In
p
ut Switch Chan
g
e
4Self-diagnosis status read
5 NULL Messa
g
e
6 Product Name Read
7 Serial Number Read
8Get
p
aramete
r
9 Set paramete
r
Item OP code page OP code Item OP code page OP code
Volume control 00h 62h V-POSITION 00h 30h
Audio Mute 00h 8Dh H-POSITION 00h 20h
Picture Mode 02h 1Ah V-HIGHT 02h 51h
SIZE 02h 70h H-WIDTH 02h 50h
CONTRAST 00h 12h CLOCK PHASE 00h 3Eh
BRIGHTNESS 00h 10h CLOCK 00h 0Eh
SHARPNESS 00h 8Ch AUTO PICTURE 00h 1Eh
COLOR 02h 1Fh UNDER SCAN 02h E3h
TINT 00h 90h BASS 00h 91h
NR 02h 20h TREBLE 00h 8Fh
COLOR TEMP. 00h 54h BALANCE 00h 93h
RED GAIN 00h 16h ALL RESET 02h CBh
GREEN GAIN 00h 18h POWER SAVE 00h E1h
BLUE GAIN 00h 1Ah PLE / PEAK BRIGHT 02h DCh
GAMMA 02h 68h ORBITER 02h DDh
COLOR CONTROL RED 00h 9Bh INVERSE/WHITE 02h C9h
COLOR CONTROL GREEN 00h 9Dh COOLING FAN - -
COLOR CONTROL BLUE 00h 9Fh SIDE MASK 02h DFh
COLOR CONTROL YELLOW 00h 9Ch DVI MODE 02h CFh
COLOR CONTROL MAGENTA 00h A0h Power ON DELAY - -
COLOR CONTROL CYAN 00h 9Eh CONTROL LOCK - -
FILM MODE 02h 23h MONITOR ID 02h 3Eh
LANGUAGE 00h 72h
COLOR SYSTEM 02h 21h
2) Simple
No Item Address code Function code End code Notes
1 Power ON '0'-'0' '!' 'CR'
2 Power OFF '0'-'0' '”' 'CR'
3In
p
ut Switch Chan
g
e '0'-'0' '
_
''CR'
4 Power Status '0'-'0' 'v'-'P' 'CR'
5In
p
ut Mode Re
q
uest '0'-'0' 'v'-'I' 'CR'
6 Picture Mode Request '0'-'0' 'v'-'M' 'CR'
3) Special
No Item Command1 Command2 Data length Notes
1 Power ON 9FH 4EH 00H
2 Power OFF 9FH 4FH 00H
3In
p
ut Switch Chan
g
e DFH 47H 01H
4 Power Status 1FH 88H 00H
5In
p
ut MODE Re
q
uest 1FH 41H 00H
6 Failure Mode Request 1FH 3FH 00H
SOH-'0'-Monitor ID-'0'-'E'-'0'-'A' STX-OP code
p
a
g
e-OP code-settin
g
value-ETX
SOH-'0'-Monitor ID-'0'-'A'-'0'-'6' STX-'C'-'2'-'1'-'6'-ETX
SOH-'0'-Monitor ID-'0'-'C'-'0'-'6' STX-OP code
p
a
g
e-OP code-ETX
SOH-'0'-'0'-Monitor ID-'B'-'0'-'4' STX-'B'-'E'-ETX
SOH-'0'-Monitor ID-'0'-'A'-'0'-'6' STX-'C'-'2'-'1'-'7'-ETX
Heade
r
Messa
g
e
SOH-'0'-Monitor ID-'0'-'A'-'0'-'C' STX-'C'-'2'-'0'-'3'-'D'-'6'-'0'-'0'-'0'-'1'-ETX
SOH-'0'-Monitor ID-'0'-'A'-'0'-'6' STX-'0'-'1'-'D'-'6'-ETX
SOH-'0'-Monitor ID-'0'-'E'-'0'-'A' STX-'0'-'0'-'6'-'0'-'0'-'0'-'0'-'1'-ETX
SOH-'0'-Monitor ID-'0'-'A'-'0'-'4' STX-'B'-'1'-ETX

NEC Corporation of America
Visual Systems Division
P60XC10 Installation Guide
60” Plasma Display Rev 1.0
www.necvisualsystems.com P60XC10 Page 10 of 10
PC Control Connector (D-Sub 9P)
NOTE: The only connections required are pins 2 (RxD), 3 (TxD) and 5 (GND).