NeedforSeat MAXNOMIC OFFICE-COMFORT Chair User manual

ASSEMBLY INSTRUCTIONS
®
CHAIRS „OFFICE-COMFORT“

Dear Customer:
®
Thank you for purchasing a MAXNOMIC Chair. You have selected a
high-quality product and we wish you many years of happy comfort.
For smooth assembly of your chair, we ask that you follow the
step-by-step instructions, especially the important safety information.
®
Your NEEDforSEAT Team
The chair shown in the photos might be a different model, however, the
assembly is the same for all of the chairs in this category.
When unpacking: you might find that the upholstery has slight wrinkles. This is
due to the tight packing. However, these will go away after a few days or simply
by using the chair.
First, create yourself a space to unpack the items and organize all of the pieces.
A second person to help you is perfect.
Before we begin:

Unpack all of the contents from the package; if you have
a delicate floor, protect it with a blanket or some other
covering before laying out the contents.
To reduce the shipping package dimensions, only one
armrest is pre-assembled. The second one will be
assembled during this process.
Careful when opening the accessories package, using a
knife with upward motions to protect the contents inside.
You will find the pillow just under the accessory package –
top portion.
Contents: 2 handles for tilt mechanism, 2 side covers for
backrest, head pillow, gas lift cylinder, wheels, bag of
screws/ universal tool, telescoping cover
Inside the bag of screws: 4 M8 35mm screws, 4 M8 30 mm
screws, 2 metal screws (Philips head), 8 washers (small,
self-locking type), 8 washers (large), 1 universal tool
Position the second armrest as shown; place the seat
upside down and remove the protective plastic.
Remove the pre-mounted screws from the underside along
with the washers.
1. 2.
3. 4.
5. 6.
7. 8.

Place the two washers as shown and place the armrest
near the seat.
First place the outside two screws with the other
washers and tighten them smoothly by hand only. Do
not force.
Insert the third screw and tighten by hand. Once in
place, use the tool to tighten all three screws.
The width of the armrest may be adjusted later in
the assembly process (if necessary).
Prepare the four long M8 screws for assembly of the
backrest as shown.
Place the backrest carefully between the brackets of
the seat bottom. It is important to NOT adjust the
position of the backrest during assembly.
Begin with the side opposite the tilt mechanism. Using
your pre-assembled M8 screws, gently insert and tighten
by hand (do not use the tool).
Now do the other side; here a second person to assist
with adjustment of the backrest would be very helpful.
9. 10.
11. 12.
13. 14.
15. 16.

The adjusted backrest can now be tightened
beginning with the two screws on each side of the
top, then the bottom screws.
Place the Philips head screw in the plastic cover.
Position the cover with the screw aiming at the hole.
Tighten the side covers using the universal tool with a
slight amount of pressure.
Do not tighten the screw too firmly – the covers are only
for appearance. Tightening the screw too hard may
damage the cover.
Now place the backrest all the way to the back position
(as shown).
Flip the complete chair over, facing down. Be careful to
not damage the chair or your floor.
Place the tilt mechanism over the hole as shown. The
adjustment parts need to face the front of the seat.
Insert the small M8 screws with one locking washer and
one regular washer then gently tighten by hand.
17. 18.
19. 20.
21. 22.
23. 24.

Place the tilt mechanism as straight as possible and
tighten the screws with the universal tool.
Place the plastic handles over the shafts of the tilt
mechanism as shown. The flat portions should point to
the front of the seat.
Once both are in the right direction, push the handles in
tightly.
Place the telescoping cover as shown over the gas lift
cylinder. The cylinder should stick out about 2 inches
(5cm).
Place the gas lift cylinder with the telescoping cover into
the hole at the base of the tilt mechanism.
Now place the base onto the cylinder and firmly press
into place.
One by one, insert the wheels into the footrest (base). You're almost there…
25. 26.
27. 28.
29. 30.
31. 32.

Now turn the chair over into the upright position, holding
the base and upper portions together (the parts become
tightly assembled once weight is placed on the chair).
You may place the head pillow over the backrest using
the elastic strip.
Bring the backrest into the upright position by pulling
upward on the tilt handle.
FINISHED! Enjoy your new MAXNOMIC® chair.
Please review this additional information:
®
adjustment button
forward / backward
adjustment button
slide left, right
Under the armrest:
adjustment button
High, low
Height adjustment Tilt mechanism
lock
Back pressure
adjustment
®
33. 34.
35. 36.
Safety Information: the maximum load/limit of the chair is
150kg (330 pounds). This can be increased to 170kg (375
pounds) with the purchase of an HD base.
PLEASE READ THE SAFETY INFORMATION ON THE LAST PAGE.

DON'T PUT YOUR WEIGHT ON THE BACKREST. WEIGHT MUST BE ON THE SEAT ITSELF.
THE CHAIR IS NOT FOR TWO USERS!
DON'T LET ANYONE PRESS DOWN ON THE BACKREST
WHILE THE SEAT IS IN A LEANING POSITION.
DO NOT SIT CLOSE TO THE FRONT SIT ALL THE WAY TO THE BACK
IMPORTANT SAFETY INFORMATION
We are not responsible for damage to the chair if these assembly instructions
are not carefully followed.
© NEEDforSEAT • Marco Wörenkämper • Wiesenstraße 13 B • 34246 Vellmar • Germany • www.needforseat.com
Pictures may differ from your actual chair and are only for demonstration. There may be differences in features and appearance.
All rights reserved
Copying of materials, even in part, only by written agreement.
® ®
NEEDforSEAT & MAXNOMIC are registrated trademarks in Germany and other countries.