Ness HTA 100 Guide

Installation and Assembly: Articulating Wall Arm for LCD screens
Model: HTA100
Tools Needed for
Assembly
Stud finder
("edge to edge"
stud finder is
recommended)
Installation to
Wood Stud Wall
Phillips
screwdriver
Drill with 1/4" and 5/32" drill bits
Important
Do not begin to install your mount product until you have read and understood the instructions.
This product should only be installed by someone of good mechanical aptitude, has experience with basic building construction, and fully understands these
Instructions. Consult a qualified professional installer if unsure.
Make sure that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
Never exceed the Maximum Load Capacity of 30 lbs.
If mounting to wood wall studs, mke sure that mounting screws are anchored into the center of the studs. Use of an “edge to edge” stud finder is highly
Recommended.
Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
Tighten screws firmly, but does not overtighten.Overtightening can damage the items, greatly reducing their holding power.

Using a stud finder, locate and mark the edges of the wood stud used in
mounting this product. Use of an edge to edge stud finder is highly
recommended. Use of level to draw a vertical line down the center of the
stud. Use wall plate as template to mark center of holes along the
vertical line. Drill two 5/32" (4mm) diaphones 2.5"(65mm) deep. Attach
wall arm assembly (AA) to wall using two #14x2.5" flat head wood
screws (D).
FOR VESA 75 MOUNTING PATTERN:
Choose whole pattern as shown below. Attach Wall arm assembly (AA) to back of screen using four M4x14mm screws (A).
Note: If whole Patten is in a pocket, attach wall arm assembly (AA) to back of screen using four M4x25mm screws (B) and four spacers (C).
FOR VESA 100 MOUNTING PATTERN:
Choose whole pattern as shown below.
Attach Wall arm assembly (AA) to
Back of screen using four M4x14mm
Screws (A).
If more or less tension is desired in the arm pivot points, do the following:
To increase tension, turn socket screw clockwise with 4mm Allen wrench (E) or 5mm Allen wrench (F).
To reduce tension, turn socket screw counter-clockwise with 4mm Allen wrench (E) or 5mm Allen
Important
Make sure that the supporting surface will safely
support the combined load of the equipment and
all attached hardware and components.
Important
Tighten screws so that wall plate is firmly attached,
but do not overtighten.Overtightening can damage
the screws, greatly reducing three holding power.
Never tighten in excess of 80 lbs.
Make sure that mounting screws are anchored into
the center of the studs. The use of an “edge to edge”
stud finder is highly recommended.
Important
If screws don’t get three complete turns in the screen inserts or if screws bottom out and
wall arm assembly is still not tightly secured, damage may occur to screen or product
may
Parts List
Description ty. Part#
AA Wall arm
assembly 1
095-0358-S
A M4x.7x14m
m phillips screw 4
520-2239
B M4x.7x25mm phillips screw
4
504-2015
C 437H spacer
4
590-5003
D #14x2. 5”flat head wood screw
2
520-2165
E 4 mm alle
n wrench 1
560-9706
F 5 mm allen wrench
1
560-9640
G concrete anchor
2
590-0097
AA
A
C
fig. 2.1
AA
A
C
fig. 2.1
AA
A
AA
DG
C
B
A

Wrench (F).Do not turns more than half a turn.
Installation to Solid Concrete and Cinder Block
Level and use wall plate as template to mark center of
holes.
Drill two 1/4" (6mm) dial, holes to a minimum depth of 2.5"
(65mm).Insert anchors (G) in holes flush with wall. Place wall arm assembly
(AA) over anchor and secure with wood screws (D).Make sure wall arm is level,
and tighten all fasteners.
Important
When installing mount wall mount on cinder block, verify that you have a minimum of 1-
3/8” of actual concrete thickness in the hole to be used for the concrete anchors. Do not
drills into mortar joints Be sure to mount in a solid part of the block, generally 1”
minimum from the side of the block? Cinder block must meet ASTM C-90 specifications.
It is suggested that a standard electric drill on slow setting is used to drill the hole instead
of a hammer drill to avoid breaking out the back of the hole when entering a void or cavity.
Concrete must be 2000 phi density minimum. Lighter density concrete may not hold concrete
Anchor.
Mark sure that the wall will safely support the combined load of the equipment and all
attached
Hardware and components