CORNING Pretium EDGE User manual

STANDARD RECOMMENDED PROCEDURE 003-809 | ISSUE 4 | DECEMBER 2011 | PAGE 1 OF 4
| PRETERMINATED SYSTEMS | CABLES | CONNECTORS | CABLE ASSEMBLIES | HARDWARE | TOOL KITS AND ACCESSORIES | TEST EQUIPMENT | SPLICE EQUIPMENT | FAN-OUT KITS | TRAINING |
=
Pretium EDGE™ Rackless
Mounting Kits
p/n 003-809, Issue 4
1. General
This document describes installation of the Pretium EDGE 1U and 4U housings onto an
overhead wire tray using mounting kit EDGE-BKT-WT-2RU and EDGE-BKT-WT-4RU
respectively or into a ladder rack using mounting kit EDGE-BKT-LR-2RU or EDGE-BKT-LR-4RU.
2. Carton Contents
Use the part numbers below to determine the carton contents for your installation.
2.1 Wire Tray Mounting Kit 2U (EDGE-BKT-WT-2RU)
• (1) Bottom Plate
• Hardware kit containing:
• (2) Waterfall 01U
• (2) Omega bracket, Horizontal position
• (2) Omega bracket, Vertical position
• (8) 10-32 x .5 stainless-steel screw
• (8) Split lock stainless-steel washer
• (4) 4-40 x .125 stainless-steel screw
• (2) 10-32 x .375 stainless-steel screw
2.2 Wire Tray Mounting Kit 4U (EDGE-BKT-WT-4RU)
• (1) Bottom Plate and bar preinstalled
• Hardware kit containing:
• (2) Omega bracket, Horizontal position
• (2) Omega bracket, Vertical position
• (8) 10-32 x .5 stainless-steel screw
• (8) Split lock stainless-steel washer
• (2) 10-32 x .375 stainless-steel screw
2.3 Ladder Rack Mounting Kit (EDGE-BKT-LR-2RU)
• (1) Bottom Plate / (2) Omega brackets preinstalled
• Hardware kit containing:
• (2) Waterfall 01U
• (4) 4-40 x .125 stainless-steel screw
• (2) 10-32 x .375 stainless-steel screw
2.4 Ladder Rack Mounting Kit 4U (EDGE-BKT-LR-4RU)
• Bottom Plate / (2) Omega brackets and bar preinstalled
• Hardware kit containing:
• (2) 10-32 x .375 stainless-steel screw
related literature |
003-794 Pretium EDGE 1U and 4U Housings

STANDARD RECOMMENDED PROCEDURE 003-809 | ISSUE 4 | DECEMBER 2011 | PAGE 2 OF 4
=
3. Tools and Materials Required
• Phillips-head screwdriver
4. Rackless Wire Tray Mounting Kit 2U or 4U
NOTE: This installation requires two people.
Step 1: The first person places the mini-frame under the wire tray.
Step 2: The second person aligns the X axis and Z axis brackets over the wire tray in line with the
slots in the mini-frame.
Step 3: The first person slides the captive screws on the underside of the mini-frame under the X
and Z axis brackets and loosely inserts the screws into the threaded nuts on the brackets.
Step 4: Adjust the kit location in the X direction (left or right) and tighten the screws in the X axis
brackets from the underside of the mini-frame.
Step 5: Adjust the kit location in the Z direction (forwards or backwards) so the housing will align
with the front of the cabinet below, if present. Consider the 4.5-inch frontal projection in
your calculations. Tighten the screws on the Z brackets from the underside.
NOTE: Calculate the Z dimension carefully. Once the kit is installed, any adjustment needed along
the Z axis will require that the housing be removed.
X axis bracket
Z axis bracket
1
Z axis
X axis
23
KPA-2557
Figure 1 — Install Rackless Wire Tray Mounting Kit (2U or 4U) (2U kit shown)

STANDARD RECOMMENDED PROCEDURE 003-809 | ISSUE 4 | DECEMBER 2011 | PAGE 3 OF 4
=
Step 6: Once the kit is secured in position, install the EDGE-01U or EDGE-04U housing, as
applicable, or any other device that has the ability to be installed into a 19-inch rack
space, by securing the mounting brackets on each side into the mounting holes on front
of the kit. If installing only one housing, place it in the top position.
Step 7: To prevent the housings from tilting in the rack, insert screws into the sides of the housing
as shown in Figure 2.
5. Rackless Ladder Rack Mounting Kit 2U or 4U
Step 1: Loosen the screws as shown in Figure 3 to allow the rails to slide.
Step 2: Place the mini-frame in the middle of the cross members. Slide the Omega brackets to
the left and right to lock the system in the horizontal (X) axis.
NOTE: The kit is able to move in X and Z directions.
Step 3: Adjust the kit location in the Z direction (forwards or backwards) so the housing will align
with the front of the cabinet below, if present. Consider the 4.5-inch frontal projection in
your calculations. Tighten the screws on the underside of the mini-frame.
KPA-2558
~4.5 inch
~4.5 inch
2U 4U
Pretium EDGE™
Pretium EDGE™
Pretium
EDGE™
Figure 2 — Install Housing(s) into Mounting Kit
2
Z axis
X axis
1
KPA-2517
2
Z axis
X axis
1
2U 4U
Figure 3 — Install Rackless Ladder Rack Kit (2U or 4U)

STANDARD RECOMMENDED PROCEDURE 003-809 | ISSUE 4 | DECEMBER 2011 | PAGE 4 OF 4
Corning Cable Systems LLC √PO Box 489 √Hickory, NC 28603-0489 USA
1-800-743-2671 √FAX [phone] √International [phone] √http://www.corning.com/cablesystems
Corning Cable Systems reserves the right to improve, enhance, and modify the features and specifications of Corning Cable Systems’ products without prior notification.
Pretium EDGE is a trademark of Corning Cable Systems Brands, Inc.All other trademarks are the properties of their respective owners. Corning Cable Systems is ISO 9001
certified.
©2009-2011 Corning Cable Systems. All rights reserved. Published in the USA.
=
NOTE: Calculate these dimensions carefully. Once the housing is installed, any adjustment needed
along the Z axis will require that the housing be removed.
Step 4: Once the kit is secured in position, install the EDGE-01U or EDGE-04U housing, as
applicable, or any other device that has the ability to be installed into a 19-inch rack
space, by securing the mounting brackets on each side into the mounting holes on front
of the kit. If installing only one housing, place it in the top position.
Step 5: To prevent the top housing from tilting in the rack, insert screws into the sides of the
housing as shown in Figure 4.
6. Waterfall Kit Installation
(Applies to 1U Housing ONLY) Open door and pull shelf out to access the underside of the shelf.
Attach waterfalls to each side of the shelf (Figure 5) with screws on the underside.
NOTE: If additional 1U housings are to be installed, contact Corning Cable Systems Customer
Services to purchase additional waterfalls.
~4.5 inch
35
4
2U 4U
Pretium EDGE™
Pretium EDGE™
Pretium
EDGE™
~4.5 inch
3
5
4
KPA-2
Figure 4 — Install Rackless Ladder Rack Kit (2U or 4U)
KPA-2383
4-40 x .125 screws
Pretium EDGE™
Pretium EDGE™
Figure 5 — Attach Waterfalls to 1U Housing