NewMar ULM-100 User manual

P.O. Box 1306
Newport Beach
California 92663
Phone: [phone]
Fax: [phone]
E-Mail: [email protected]
www.newmartelecom.com
Unity Low Voltage
Disconnect & Monitor
Installation/Operation Manual
Model: ULM-100
Table of Contents Page Table of Contents Page
1.0 Overview 2 5.14 LVD Level Mapping 4
2.0 Materials Provided 2 5.2 Meter 4
3.0 Mounting 2 5.21 Voltage Monitoring 4
3.1 Rack Ears 2 5.23 Backlighting Adjustment 4
4.0 Wiring 2 5.24 Temperature Monitoring 4
4.1 Rectifier Input 2 5.25 Meter Power Source Selector 4
4.2 Battery Input 2 5.26 Restore to Factory Settings 5
4.3 Load Output 2 5.3 Battery Circuit Breaker 5
4.4 Alarms 3 5.4 Alarm LED 5
5.0 Operation & Adjustments 3 6.0 Connecting Rectifier Types 5
5.1 Low Voltage Disconnect 3 6.1 Unity Rectifier Shelf (URS) 5
5.1 Manual/Auto Selector Switch 4 6.2 Power Modules (PM Series) 5
5.12 LVD Adjustment 4 7.0 Troubleshooting 6
5.13 LVD Alarms: Pre-Disconnect & Disconnect 4 8.0 Specifications 6
9.0 Outline & Mounting Drawing 7
M-ULM100
030315

P.O. Box 1306
Newport Beach
California 92663
Phone: [phone]
Fax: [phone]
E-Mail: [email protected]
www.newmartelecom.com
1.0 Overview
This 1RU assembly contains numerous DC control and monitoring features that integrate power and distribution
components into a highly functional system. Built in features include: low voltage disconnect, digital monitor of voltage
and amperage, battery disconnect breaker, and alarm contacts. The digital display monitors bus voltage, battery
voltage, system output current, and low voltage connect/disconnect set points. Alarm contacts actuate on low voltage
and battery disconnect conditions. Rear panel bus bars provide ample terminal landings for easy integration with rack
mount rectifiers, distribution panels and batteries.
Figure 1: Overview - Front Panel
2.0 Materials Provided
Qty. Description
2 Mounting ears for 19” rack mounting (Note: Contact Newmar Technical Support for 23” rack mount ears)
6 6-32 x 3/8” Phillips head screws, black-mount the two mntg. ears
1 Molex pigtail alarm connector/wire assembly (six wires)
10 ¼-20 Hex Head bolt for rectifier, battery input & load connection
10 ” split lock washer - one per 1/4-20 Hex Head bolt above
1 Installation/Operation Manual
3.0 Mounting
3.1 Rack Ears: One pair of rack ears for 19” rack mounting are provided. Optional 23” rack mounting ears are available
- please contact Newmar for p/n 699-3918-0, qty.2. Two mounting options are available: Flush mount and 6” off-set or
‘center mount’.
4.0 Wiring
Figure 2: Wiring - Rear Panel
See Table 1 for Recommended Wire Size
4.1 Rectifier Input: Three sets of landings for ¼” ring lug terminals are provided for rectifier Hot and RTN input connections.
Maximum total rectifier current is 100 Amps. See section 6.0 for more information on connecting Newmar rectifiers.
4.2 Battery input: One pair of landings for ” ring lug terminals are provided for connecting the battery. The ULM-100
incorporates a 100 Amp battery breaker on the front panel however for long battery cable runs we recommend a fuse or
breaker wired on the battery hot side, located as close to the battery as practical.
4.3 Load output: One pair of landings for ” ring lug terminals are provided for connecting the load or feeding a
distribution panel such as Newmar model DST-FB, DST-10, DST-20A or FDP fuse panels. Maximum load current is 100 Amps.
2
Temperature
Sensor
¼
¼
¼

P.O. Box 1306
Newport Beach
California 92663
Phone: [phone]
Fax: [phone]
E-Mail: [email protected]
www.newmartelecom.com
Table 1: Wire Size Chart
Amperage Minimum Wire Size in AWG
1-10A #16
11-20A #14
21-30A #12
31-35A #10
36-50A #8
51-70A #6
71-90A #4
91-100A #2
4.4 Alarms: Pre-disconnect & Disconnect- Two sets of Form C alarm contacts are provided for the following: Pre-LVD
Disconnect & LVD Disconnect. Wiring is via the Molex six conductor alarm wire pigtail included with the ULM-100. See
section 5.12 & 5.13 for information on setting Pre-disconnect and LVD activation thresholds.
5.0 Operation & Adjustments
Figure 3: LCD Menu
5.1 Low Voltage Disconnect: The ULM-100 incorporates a 100 Amp solid state LVD circuit which automatically removes
the battery when battery voltage drops to a pre-set DISCONNECT threshold (or when manually activated- see section
5.11) and automatically re-connects the battery when battery voltage rises above the selected CONNECT threshold (see
Specification 8.0 for default LVD thresholds and adjustment ranges)
3

P.O. Box 1306
Newport Beach
California 92663
Phone: [phone]
Fax: [phone]
E-Mail: [email protected]
www.newmartelecom.com
5.11 Manual/Auto selector switch: The LVD selector switch sets the way the LVD circuit functions.
• Manual connect - Battery always online
• Automatic - LVD function enabled (factory default)
• Manual disconnect - Battery always offline
5.12 LVD Adjustment: The ULM-100 offers easy adjustment of both dis-connect and re-connect LVD settings without the
need for an external, adjustable power supply. These thresholds can be selected from the SETTINGS page using the menu
knob, the default factory setting for the particular item is also displayed. A press on the menu knob will save the settings
and is retained even after powering down the unit. LVD threshold adjustment can be made while the system is operating.
5.13 LVD Alarms: Pre-disconnect & disconnect - Two external alarms can be triggered by the ULM-100: the Pre-disconnect
(‘PRELVD’) and the LVD dis-connect (‘LVDDISCON’). The LVD Pre-disconnect alarm is a warning to an impending battery
disconnect. It is triggered by an adjustable voltage thresholds set above the LVD dis-connect threshold and below the
re-connect threshold. The LVD dis-connect alarm is automatically set using the LVD dis-connect threshold (see 5.12). Both
alarms will trigger the LED Alarm light.
5.14 Voltage Level Mapping - 12 VDC example shown
12.5v NORMAL VOLTAGE
12.3v LVD RE-CONNECT (ADJUSTABLE)
11.6v PRE-LVD ALARM (ADJUSTABLE)
11.0v LVD DIS-CONNECT (ADJUSTABLE)
Normal Voltage - Typical system voltage with rectifiers supplying load(s), batteries not deeply discharged.
LVD Re-Connect - Level at which the battery will be re-connected after a dis-connect event when AC power is restored.
Pre-LVD Alarm - Level at which the pre-LVD alarm contact triggers as an early warning for a low battery disconnect. (See
Specification Section 8.0 for factory default.)
LVD Dis-Connect - Minimum allowable battery voltage level has been reached and will disconnect battery to prevent
damage. Will also trigger LVD alarm. (See Specification Section 8.0 for factory default.)
5.2 Meter
Figure 4: LCD Home Screen
5.21 The home screen shows DC voltage, DC current and Ambient temperature in degrees Celsius. The display always
returns to the home screen after 30 seconds of inactivity. A push of the menu button will display the alarm screen and
rotating the knob will send it to adjacent display pages.
5.22 Plant Current Monitoring: The total current being produced by the rectifier(s) connected is displayed on the main
screen. This includes current drawn by the load and battery charging current.
5.23 Back Lighting: The ULM-100 allows the user to adjust LCD backlight level to match environment lighting or suit user
preferences. Changes can be made in the settings menu and is adjustable from 20% to 100% levels.
5.24 Temperature Monitoring: Ambient temperature is displayed on the home screen in Celsius and on the temperature
screen in both Fahrenheit and Celsius. The sensor is located on the front panel next to the alarm LED.
5.25 Meter Power Source Selector: The LCD meter can be powered from the rectifier side or the battery side by using the
selector switch. Powering the meter from the rectifier side(default) causes the ULM-100 to completely shutdown during a
Low battery voltage disconnect thus reducing battery drain. Powering from the battery side will allow the LCD meter to
continue operating even with a an LVD disconnect event.
4

P.O. Box 1306
Newport Beach
California 92663
Phone: [phone]
Fax: [phone]
E-Mail: [email protected]
www.newmartelecom.com
5.26 Restore to Factory Settings: The ULM-100 comes with default factory settings that will work for most applications.
This feature will clear all user setting changes back to factory settings. This is particularly useful in the event the ULM-
100 contactor begins cycling. Example: Connect and Disconnect thresholds set too close toghether. The ‘Restore Setting’
feature can be activated in the settings menu.
5.3 Battery Circuit Breaker: The Hot side of the battery input goes to a front panel mounted 100 Amp circuit breaker
labeled ‘BATTERY’. This circuit breaker incorporates auxiliary contacts which will alert the user via the LCD display (‘Battery
offline’) and red ‘Alarm’ LED, should the breaker trip or be placed in to the OFF position inadvertently.
5.4 Alarm LED: This red LED will illuminate when any of the following conditions occur:
• Battery circuit breaker in OFF position
• LVD Pre-disconnect threshold crossed (see section 5.13 for more info)
• LVD activation- manually or automatically
6.0 Connecting Rectifier Types
The ULM-100 will accept any filtered rectifier input (s) providing total rectifier amperage does not exceed 100 Amps. See
Figure 5 and 6 for wiring examples of Newmar Unity Rectifier Shelf (URS) and Power Modules (PM Series).
6.1 Unity Rectifier Shelf (URS): The URS has two sets of output terminals. Both are marked ‘OUTPUT/BATTERY’. One set uses
a barrier style terminal block with # 6 screw terminals located near the optional UFP-5 fuse panel location and the other
is a european style terminal block on the opposite end of URS rear panel which will accommodate up to 8 AWG wire size.
The ULM-100 Rectifier Input can be connected to either one of these two sets of output terminals.
UFP-5 Note: If using the optional Unity UFP-5 GMT Fuse Distribution Panel, the UFP-5 Hot & RTN/GND input leads will have
to be extended with a pair of 14 AWG wires and crimp butt connectors. Connect extended UFP-5 input wires to the ULM-
100 LOAD terminals.
Figure 5: ULM-100 and Unity Rectifier Shelf (URS) with Optional UFP-5 Wiring Diargram
6.2 Power Module (PM Series): One or more Newmar PM Series Power Modules can be connected to the ULM-100 Rectifier
Input (100 Amps max. total). Use the ‘Vout’ or diode isolated terminal when connecting 2 or more PM’s in parallel. Figure
6, ULM-100 and Power Module wiring diagram - next page.
5

P.O. Box 1306
Newport Beach
California 92663
Phone: [phone]
Fax: [phone]
E-Mail: [email protected]
www.newmartelecom.com
7.0 Troubleshooting
• Meter Display Errors: In the event the LCD display gets out of sync with the micro-controller and displays incorrect
information, a simple fix is to power cycle the LCD. To power cycle the meter without disconnecting the load: first ensure
the rectifiers are on, slide the breaker to OFF position then slide the meter power to ‘Battery’ then back to ‘Rectifier’. This will
briefly disconnect power to the meter and allow a safe power cycling and clear the display error. Turn on battery breaker.
• LVD Stability Issues After Settings Change: If the LVD contactor cycles frequently after making changes to the LVD
default settings, the ULM-100 can be restored to factory settings to aid in troubleshooting (see 5.26 and the menu diagram
for details).
8.0 Specifications
Electrical
Nominal System Voltage: 12, 24 or 48 VDC
Voltage Range: 8 to 65 vdc
Grounding: Positive or Negative (polarity insensitive)
Maximum Continuous Current: 100 Amps DC
Battery Breaker: 100 Amps with handle guard
Low Voltage Battery Disconnect: 100 Amp, solid state (FET)
Factory Default:
LVD Set Points 12 Volt 24 Volt 48 Volt
Disconnect 10.4V 21.0V 42.0V
Connect 12.0V 24.5 49.0V
Factory Default LVD Pre-Disconnect Alarm Threshold (Adjustable):
System Voltage 12V 24V 48V
LVD Pre- Disconnect 11.2V 22.8V 45.5V
6
Figure 6: ULM-100 and Power Module
Mechanical
Chassis: Aluminum with vinyl lamination, black powder
coat front panel
Terminals: Plated copper. Landings for up to three
rectifier inputs, with separate battery & load
terminals
Rack Size: 19”, 1U
Cooling: Convection
Dimensions: 1.75” H x 19” W x 11” D
Weight: 6.25 Lbs.
Environmental
Operating Temperature range: 0 to +60°C
* Fuse Hot near
battery on long
cable runs

P.O. Box 1306
Newport Beach
California 92663
Phone: [phone]
Fax: [phone]
E-Mail: [email protected]
www.newmartelecom.com
7
9.0 Outline & Mounting Dimensions