Nexgrill 720-0486 Quick reference guide

PLEASE CONTACT 1-800-913-8999 FOR ASSISTANCE
ABOUT ASSEMBLY OR GRILL OPERATION
DO NOT RETURN TO THE PLACE OF PURCHASE
ASSEMBLY & OPERATING INSTRUCTIONS
FOR OUTDOOR USE ONLY
Model: 720-0486
FOR PROPANE GAS USE ONLY J05Y06P-1

WARNING
Do not try to light this appliance without first reading the “LIGHTING INSTRUCTIONS”
section in this manual.
MESSAGE TO OUR CONSUMERS
Thank you for selecting our stainless steel gas grill.
Because this appliance contains features which may not be found on other grills, we
recommend that you read this entire booklet before your first use. Keep it in a handy
place as it has answers to questions that may occur during future use.
Read this booklet carefully and be sure your gas grill is properly assembled, installed and
maintained. Failure to follow these instructions could result in serious bodily injury and/or
property damage. This gas grill is intended for outdoor use only and is not intended to be
installed in or on recreational vehicles or boats.
NOTE TO INSTALLER: Leave these instructions with the consumer after installation.
NOTE TO CONSUMER: Retain for future reference.
IMPORTANCE
Danger
I f you smell gas:
1 Shut off gas to the appliance.
2 Extinguish any open flame.
3 Open lid
4 If odor continues, keep away from the appliance
and immediately call you gas supplier or your fire
department.
Warning
1.Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
2.An LP cylinder not connected for use shall not be
stored in the vicinity of this or any other appliance.
WARNING
Combustion byproducts produced when using this
product contain chemicals known to the State
of California to cause cancer, birth defects, or
other reproductive harm.
WARNING
Failure to comply with these instructions could result
in a fire or explosion that could cause serious bodily
injury, death, or property damage.
WARNING
Your grill will get very hot. Never lean over the cooking area while using your grill. Do not touch cooking
surfaces, grill housing, Lid or any other grill parts while the grill is in operation, or until the gas grill has
cooled down after use. Keep any electrical supply cord and the fuel supply hose away from any heated
surface.

TABLE OF CONTENTS
SECTION ONE
Table of Contents & Importance--------------
Precautions----------------------------------------1-2
Placement of the Grill--------------------------- 3
SECTION TWO
Assembly Instructions------------------------4-13
To Match Light The Grill-----------------------14
Gas Hook Up-----------------------------------15-16
Installer Final Check List------------------------16
Leak Testing------------ -----------------------17-18
SECTION THREE
Operating Instruction--------------------------19-20
Grill Lighting Instruction-----------------------20-23
Lighting Illustration-----------------------------24
SECTION FOUR
Care & Maintenance-------------------25-26
SECTION FIVE
Trouble Shooting-------------------------27-28
Exploded View----------------------------29
Part List-------------------------------------30
Operating Parts & Grilling Hints---------31
SECTION SIX
Grill Cooking Chart----------------------32-34
SECTION SEVEN
Grill Recipe Suggestions--------------35-37
SECTION EIGHT
Limited Warranty------------------------38

PRECAUTIONS
WARNING
Do not try to light this appliance without
first reading the “LIGHTING
INSTRUCTIONS” section in this manual.
TESTED IN ACCORDANCE WITH ANS
Z21.58a •CSA 1.6a-2006 STANDARD FOR
OUTDOOR COOKING GAS APPLIANCES.
THIS GRILL IS FOR OUTDOOR USE ONLY.
Check your local building codes for the
proper method of installation. In the
absence of local codes, this unit should be
installed in accordance with the National
Fuel Gas Code ANSI Z223.1/NFPA 54,
OR CSA B149.1 Natural Gas and
Propane Installation Code, and the
National Electrical Code, ANSI/NFPA 70,
or Propane storage and handling code,
B149.2.
CALIFORNIA PROPOSITION 65-WARNING
The burning of gas fuel generates some by-
products, which are on the list of
substances, which are known by the State
of California to cause cancer or
reproductive harm. California law requires
businesses to warn customers of potential
exposure to such substances. To minimize
exposure to these substances, always
operate this unit according to the use and
care manual, ensuring you provide good
ventilation when cooking with gas.
SAFETY PRACTICES TO AVOID PERSONAL
INJURY
When properly cared for, your stainless
steel grill will give safe, reliable service for
many years. However, extreme care must
be used since the grill produces intense
heat and that can increase accident
potential. When using this appliance basic
safety practices must be followed, including
he following:
Read this Care and Use Manual carefully
and completely before using your grill to
reduce the risk of fire, burn hazard or other
injury.
Do not repair or replace any part of the grill
unless specifically recommended in this
manual. All other service should be referred
to a qualified technician.
CHILDREN SHOULD NOT BE LEFT
ALONE OR UNATTENDED IN AN AREA
WHERE THE GRILL IS BEING USED.
NEVER ALLOW THEM TO SIT, STAND
OR PLAY ON OR AROUND THE GRILL
AT ANY TIME.
1

PRECAUTIONS
Moist or damp potholders on hot surfaces
may cause burns from steam. Do not use a
towel or bulky cloth in place of potholders.
Do not let potholders touch hot portions of
the grill rack.
Grease is flammable. Let hot grease cool
before attempting to handle it. Avoid letting
excess grease deposits collect in the
grease tray at the bottom of the grill’s
firebox. Clean often.
DO NOT USE ALUMINUM FOIL TO LINE
THE GRILL RACKS OR GRILL BOTTOM.
This can severely upset combustion air flow
or trap excessive heat in the control area.
For proper lighting and performance of the
burners keep the burner ports clean. It is
necessary to clean them periodically for
optimum performance. The burners will
only operate in one position and must be
mounted correctly for safe operation.
Clean the grill with caution. Avoid steam
burns; do not use a wet sponge or cloth to
clean the grill while it is hot. Some cleaners
produce noxious fumes or can ignite if
applied to a hot surface.
INSECT WARNING!!! Spiders and insects
can nest in the burners of this and any
other grill, and cause the gas to flow
improperly. This is a very dangerous
condition which can cause a fire to occur
behind the valve panel, thereby damaging
the grill and making it unsafe to operate.
Inspect the grill twice a year.
Be sure all grill controls are turned off and
the grill is cool before using any type of
aerosol cleaner on or around the grill. The
chemical that produces the spraying action
could, in the presence of heat, ignite or
cause metal parts to corrode.
DO NOT STORE ITEMS OF INTEREST
TO CHILDREN AROUND OR BELOW
THE GRILL OR IN THE CART. NEVER
ALLOW CHILDREN TO CRAWL INSIDE
OF THE CART.
Never let clothing, pot holders or other
flammable materials come in contact with
or too close to any grate, burner or hot
surface until it has cooled. Fabric may
ignite and result in personal injury.
For personal safety, wear proper apparel.
Loose fitting garments or sleeves should
never be worn while using this appliance.
Some synthetic fabrics are highly
flammable and should not be worn while
cooking.
Only certain types of glass, heat-proof
glass ceramic, earthenware, or other
glazed utensils are suitable for grill use.
These types of materials may break with
sudden temperature changes. Use only on
low or medium heat settings according to
the manufacturer’s directions.
Do not heat unopened food containers as
a build-up of pressure may cause the
container to burst.
Use a covered hand when opening the
grill lid. Never lean over an open grill.
WHEN LIGHTING A BURNER, ALWAYS
PAY CLOSE ATTENTION TO WHAT
YOU ARE DOING. BE CERTAIN YOU
ARE TURNING THE IGNITER LABELED
FOR THE BURNER YOU INTEND ON
USING.
When using the grill, do not touch the grill
rack, burner grate or immediate
surroundings as these areas become
extremely hot and could cause burns. Use
only dry potholders. 2

PRECAUTIONS
Do not use the grill for cooking
excessively fatty meats or products which
promote flare-ups. Do not operate the grill
under unprotected combustible
construction. Use only in well ventilated
areas. Do not use in buildings, garages,
sheds, breezeways or other such
enclosed areas. THIS UNIT IS FOR
OUTDOOR USE ONLY.
Keep the area surrounding the grill free
from combustible materials, trash, or
combustible fluids and vapors such as
gasoline or charcoal lighter fluid. Please
check the surrounding area before use.
And keep a minimum of 24”(61cm)
clearance from combustible material. Do
not obstruct the flow of combustion and
ventilation air. Keep the ventilation
openings of the cylinder enclosure free
and clear from debris. This must be
checked before each use. If the unit is
stored indoors ensure that it is cool. If
propane is used, the cylinder must be
unhooked and the propane cylinder stored
outside in a well ventilated area, out of the
reach of children.
DO NOT USE BRIQUETTES OF ANY
KIND IN THE GRILL.
This stainless steel grill is designed for
optimum performance without the use of
briquettes. Do not place briquettes on the
flame tamer as this will block off the area
for the grill burners to vent. Adding
briquettes can damage ignition components
and knobs, and void the warranty.
Keep the back of the cart free and clear
from debris. Keep any electrical supply
cord, or the rotisserie motor cord away
from the heated areas of the grill.
Never use the grill in extremely windy
conditions. If located in a consistently windy
area (oceanfront, mountaintop, etc.) a
windbreak will be required (see below).
Always adhere to the specified clearance.
NEVER USE A DENTED OR RUSTY
PROPANE TANK.
PLACEMENT OF THE GRILL
CLEARANCE
To Non-Combustible Construction
A minimum of 24”(61cm) clearance from the
back of the grill to non-combustible
construction is required for the lid to open
fully.
DO NOT INSTALL THIS UNIT INTO
COMBUSTIBLE ENCLOSURES!
LOCATION
When determining a suitable location take
into account concerns such as exposure to
wind, proximity to traffic paths and keeping
any gas supply lines as short as possible.
Locate the grill only in a well-ventilated area.
Never locate the grill in a building, garage,
breezeway, shed or other such enclosed areas
without an approved ventilation system. During
heavy use, the grill will produce a lot of smoke.
Lock the wheels after the grill is placed in a
suitable position according to the sticker
located behind the right door. Keep any
electrical supply cord and the fuel supply hose
away from any heated surfaces. Storage of an
outdoor gas cooking appliance indoors is
permissible only if the cylinder is disconnected
and removed from the appliance.
This outdoor cooking gas appliance shall be
used only outdoor and shall not be used in a
building, garage or any other enclosed area.
This appliance is not intended to be installed
on or on recreational vehicles and/or boats
3

ASSEMBLY INSTRUCTIONS
PLEASE READ THE INSTURCTION CAREFULLY AND FOLLOW STEP
BY STEP
●Propane Tank is not included
●Philips head Screwdriver (not provided)
●The following hardware is provided
4
8pcs
1/4x50mm
philips head screw
4pcs
3/16
3
hex nut
3/16 4pcs
9
lockingwa s h e r
4
5
5/32x10mm 2pcs
1/4x15mm
philips head screw
2
1
QuantitySpecificationDes c r i pt i on
Item
7
philips head screw
locking
wa s h e r 5/32 2pcs
lockingwa s he r
1/4
8
philips head screw
3/16x10mm 12pcs
1/4
flat wa s h e r
64pcs
28pcs
32pcs

ASSEMBLE INSTRUCTIONS
5
ASSEMBLY INSTRUCTIONS
PLEASE READ THE INSTRUCTIONS CAREFULLY AND FOLLOW STEP
BY STEP.
TOOLS REQUIRED:
(1) PHILIPS HEAD SCREWDRIVER – NOT PROVIDED
STEP 1:
Attach bottom panel to side panel with 4 pieces 1/4x50mm philips head
screws with 4 pieces 1/4 locking washer as shown figure below.
STEP 2:
Attach the black panel to the two side panels with 4 pieces 1/4x15mm philips
head screws and 4 pieces 1/4 locking washers, and attach the gas tank
supporting onto the bottom with 4 pieces 1/4x15mm philips head screws and
4 pieces 1/4 locking washers.

ASSEMBLY INSTRUCTIONS
6
STEP 3:
Attach the casters to the legs of the bottom.Tighten caster bolts securely
using hex nut wrench provided in parts pack.
STEP4:
Attach door shaft to the outside of cart legs with 4 pieces ¼’’x50mm philips
head screws and 4 pieces 1/4 locking washer, then using 2 pieces
¼’’x15mm philips head screws and 2pieces 1/4 locking washers to inside of
cart legs. Then place the basket into basket brackets of left side panel.
1/4X15mm
head screws
1/4x50mm
philips head screws

ASSEMBLY INSTRUCTIONS
7J05Y06P-2
STEP 5:
Remove the grill head unit from carton, place onto cart from above as
shown on diagram (below). And secure to cart frame.
Caution!!! Head unit is heavy, to avoid injury, we strongly recommend
2 or more people for this step.
STEP 6:
Secure the head unit to cart with 4 pieces 1/4” x 15mm philips head
screws and 4 pieces flat washers as shown on diagram below.
(Note: Remove cooking grids and flame tamers before this step)

8
ASSEMBLY INSTRUCTIONS
STEP 7:
Attach the left door handle using 4pieces 3/16x10mm philips head screws
with 4 pieces 3/16 locking washers. Then attach right door handle using 4
pieces 3/16x10mm philips head screws with 4pieces 3/16 locking washers
as shown on below figure.
STEP 8:
Attach the hinge pin in bottom of right side door into hole at the bottom
right front cart leg, then align door with right side door bracket. Depress
spring pin located on top edge of door and slide door lomard right side
door bracket until spring pin locks into hole in door bracket.

ASSEMBLY INSTRUCTIONS
9
STEP 9:
•Attach side burner front panel to side burner with 3 pieces ¼’’x15mm
philips head screws with 3 pieces locking washers.
•Insert 4pieces ¼’’x15mm philips head screws with 4pieces ¼’’ locking
washers halfway to the right side grill body panel.
•Place side burner assembly keyholes over bolts and slide down,then
tighten securely.
•Fasten side burner front panel to grill body with 1pieces 5/32’’x10mm
philips head screws and 1pieces 5/32’’ locking washers.
STEP 10:
• Attach side shelf front panel to side shelf with 3pieces 1/4x15mm philips
head screws with 3 pieces ¼’’ locking washers.
•Insert 4 pieces 1/4x15mm philips head screws with 4 pieces ¼’’ locking
washers halfway to the left side grill body panel.
•Place side table assembly keyholes over bolts and slide down,then tighten
securely.
•Fasten side shelf front panel to grill body with 1pieces 5/32’’x10mm philips
head screw and 1 pieces 5/32’’ locking washers.

ASSEMBLY INSTRUCTIONS
10
STEP 11:
Attach the grease collector into slide rails under firebox from back of grill.
Place the grease tray into rails on grease slide.
STEP 12:
Attach the tool drawer into front opening under control panel by dropping
roller wheels into side channels.

ASSEMBLY INSTRUCTIONS
11
STEP 13:
Place the heat distribution plates on lower level of grill body assembly
directly above burners. Place porcelain cast iron cooking grills on support
ribs directly above heat distribution plates. Place warming rack in grooves
so that it sits above the cooking grills.
STEP 14:
Fasten Rotisserie motor bracket to grill body with 2 pieces 3/16’’x10mm
philips head screws and 2pieces 3/16” hex nuts with 2 pieces 3/16 ‘’ locking
washers.
Fasten Rotisserie bracket to grill body with 2 pieces 3/16’’x10mm philips
head screws and 2pieces 3/16” hex nuts with 2 pieces 3/16 ‘’ locking
washer.

ASSEMBLY INSTRUCTIONS
12
STEP 15:
Unscrew the ignition battery cap. (Found at far-left of control panel)
Insert battery into ignition box with positive terminal facing outward.
Replace the ignition battery cap after the battery has been installed.

ASSEMBLY INSTRUCTIONS
STEP 16:
Attach propane gas tank to regulator inlet fitting by turning the regulator
clockwise as shown in figure below. LP gas cylinder must be fitted with a
listed overfill prevention device (OPD). Secure liquid propone gas cylinder
to the slide out tray using the gas cylinder retention screw.
CYLINDER TANK FIXED
13

TO MATCH LIGHT THE GRILL
1. If the burner will not light after several attempts then the burner can be
match lit.
2. If you’ve just attempted to light the burner with the igniter, allow 5
minutes for any accumulated gas to dissipate. Keep your face and hands
as far away from the grill as possible. Insert a lit extended match or lighter
through the cooking grids to the burner. Press the control knob and rotate
left to the HI setting, continue to press the knob until the burner ignites.
Burner should light immediately. If the burner does not light in 4 seconds
turn the knob off, wait 5 minutes and try again.
14

GAS HOOK-UP
NEVER CONNECT AN UNREGULATED
GAS SUPPLY LINE TO THE APPLIANCE.
USE THE REGULATOR/HOSE
ASSEMBLY SUPPLIED.
This is a liquid propane configured grill.
Do not attempt to use a natural gas supply.
Total gas consumption (per hour) of this
stainless steel gas grill with all burners on
“IGNITE/HI”:
Main burner 60,000 Btu/hr.
Side burner 12,000 Btu/hr
Rear burner 10,000 Btu/hr
Total 82,000 Btu/hr.
L.P. TANK REQUIREMENT
A dented or rusty L.P. tank may be
hazardous and should be checked by your
L.P. supplier. Never use a cylinder with a
damaged valve. The L.P. gas cylinder
must be constructed and marked in
accordance with the specifications for L.P.
gas cylinders of the U.S. Department of
Transportation (DOT) or the National
Standard of Canada, CAN/CSA-B339,
Cylinders, Spheres and Tubes for
Transportation of Dangerous Goods; and
Commission, as applicable. Overfilling
prevention device (OPD) shall be provided
on cylinder & QCCI connection on the
cylinder valve, ANSI/CGA-V-1. The
cylinder supply system must be arrange
for vapor withdrawal. Make sure tank is
leveled with bottom panel for proper vapor
withdraw. The cylinder must include a
collar to protect the cylinder valve. The
cylinder must be provided with a shut off
valve terminating in an L.P. gas supply
cylinder valve outlet specified, as
applicable, for connection type QCC1 in
the standard for compressed gas
cylinder valve outlet and inlet
connection ANSI/CGA-V-1.
Manifold pressure: 11 inches water column
(W.C.).
L.P. GAS HOOK-UP
Ensure that the rubber “O” Ring on the LP
cylinder valve are in place and that the
hose does not come into contact with the
grease tray or the grill head. Set the liquid
propane gas cylinder into the slide-out tray
making sure that the cylinder is level with
the bottom panel, thus allowing proper
vapor withdrawal.
CONNECTION
Your stainless steel grill is equipped with
gas supply orifices for use only with liquid
propane gas. It is also equipped with a high
capacity hose/regulator assembly for
connection to a standard 20lb. L.P. cylinder
(18-1/4” (46.35cm) high, 12-1/4”(31cm)
diameter). To connect the L.P. gas supply
cylinder, please follow the steps below:
1. Make sure tank valve is in its full off
position (turn clockwise to stop)
2. Check tank valve to assure it has
proper external male threads (type 1
connection per ANSIZ21.81)
3. Make sure all burner valves are in their
off position.
4. Inspect valve connections, port, and
regulator assembly. Look for any
damage or debris. Remove any debris.
Inspect hose for damage. Never
attempt to use damaged or obstructed
equipment. See your local L.P. gas
dealer for repair.
15

GAS HOOK-UP
5. When connecting regulator assembly to
the valve, hand tighten the quick
coupling nut clockwise to a complete
stop. Do not use a wrench to tighten.
Use of a wrench may damage the quick
coupling nut and result in a hazardous
condition.
6. Open the tank valve fully
(counterclockwise). Use a soapy water
solution to check all connections for
leaks before attempting to light the grill,
see below. If a leak is found, turn the
tank valve off and do not use the grill
until a local L.P. gas dealer can make
repairs.
To disconnect L.P. gas cylinder:
1. Turn the burner valves off.
2. Turn the tank valve off fully (turn
clockwise to stop).
3. Detach the regulator assembly from the
tank valve by turning the quick coupling
nut counterclockwise.
INSTALLER FINAL CHECK LIST
9Specified clearance maintained
24”(61cm) from combustibles.
9All internal packaging removed.
9Knobs turn freely.
9Burners are tight and sitting properly
on orifices.
9Pressure regulator connected and set.
Gas connections to grill using hose &
regulator assembly provided (pre-set
for 11.0” water column).
9Unit tested and free of leaks.
9User informed of gas supply shut off
valve location
USER, PLEASE RETAIN THIS MANUAL
FOR FUTURE REFERENCE.
PROPANE CYLINDER CAUTIONS
a) Do Not store a spare LP-gas
cylinder under or near this
appliance.
b) NEVER fill the cylinder beyond 80
percent full.
c) If the information in “a” and “b” is
not followed exactly, a fire causing
death or serious injury may occur.
16

LEAK TESTING
Only those parts recommended by the
manufacturer should be used on the grill.
Substitution will void the warranty. Do not use
the grill until all connections have been
checked and do not leak.
GAS FLOW CHECK
Each grill burner is tested and adjusted at the
factory prior to shipment; however, variations
in the local gas supply may make it necessary
to adjust the burners. The flames of the
burners should be visually checked.
Flames should be blue and stable with no
yellow tips, excessive noise or lifting. If any of
these conditions exist, check to see if the air
shutter or burner ports are blocked by dirt,
debris, spider webs, etc. If you have any
questions regarding flame stability, please call
customer service 1-800-913-8999 .
Check all gas supply fittings for leaks
before each use. It is handy to keep a
spray bottle of soapy water near the
shut-off valve of the gas supply line.
Spray all the fittings. Bubbles indicate
leaks.
ALWAYS CHECK FOR LEAKS AFTER
EVERY L.P. TANK CHANGE
17
GENERAL
Although all gas connections on the grill are
leak tested at the factory prior to shipment, a
complete gas tightness check must be
performed at the installation site due to
possible mishandling in shipment, or excessive
pressure unknowingly being applied to the unit.
Periodically check the whole system for leaks
following the procedures listed below. If the
smell of gas is detected at anytime you should
immediately check the entire system for leaks.
BEFORE TESTING
Make sure that all packing material is removed
from the grill including the burner tie-down
straps.
DO NOT SMOKE WHILE LEAK TESTING.
NEVER PERFORM LEAK TEST WITH AN
OPEN FLAME.
Make a soap solution of one part liquid
detergent and one part water. You will need a
spray bottle, brush, or rag to apply the solution
to the fittings. For the initial leak test, make
sure the L.P. cylinder is full.
TO TEST
1. Make sure the control valves are in the “OFF”
position, and turn on the gas supply.
2. Check all connections from the LP gas
regulator and supply valve up to and including
the connection to the manifold pipe assembly
(the pipe that goes to the burners). Soap
bubbles will appear where a leak is present.
3. If a leak is present, immediately turn off the
gas supply and tighten the leaky fittings.
4. Turn the gas back on and recheck.
5. Should the gas continue to leak from any of
the fittings, turn off the gas supply and contact
customer service at 1-800-913-8999.