Nexo P Series User manual

PAGE 1 OF 4
- Read this document before using.
- Keep this document.
- Observe all warnings and cautions.
PNI-P12TO2L15
DP5816 –01b - DI
P12 Under 2xL15 Rigging System
Contents:
X1 Ceiling Plate
X1 Left Plate
X1 Right Plate
X2 L15 Plate
X2 Main Plate
X8 M10x30 (a)
X8 M10x16 (a)
X2 M6x30 (a)
X1 Left spacer
X1 Right
spacer
(a): The type of the screws may differ from the representation
Weight: 22.5 kg / 49.5 lb

PAGE 2 OF 4
- Read this document before using.
- Keep this document.
- Observe all warnings and cautions.
Dimensions:
For fixation, you have the choice between M8 and M10 (Fasteners not provided)
WARNINGS
Ensure that the mounting location and fasteners can support at least 4 times the weight of all the installed cabinets, auxiliary
equipment and cables.
Use only the provided screws (thread lock coated) and accessories.
Implementation of L15
Prepare the Main plates by screwing the M10x30 screws on the holes (see picture below), do not tighten completely and leave
at least 6mm.
Assemble the Plates on each side of L15 using the M10x16 screws.
CARDIO mode
OMNI Mode



















PAGE 3 OF 4
- Read this document before using.
- Keep this document.
- Observe all warnings and cautions.
Assembly on the ceiling plate
Place the assembly below the ceiling plate.
Tighten the screws. Secure with the 2 provided M10x30 screws.
Implementation of P12
Place the adhesive left
rubber pad on the left plate.
Place the adhesive right rubber
pad on the right plate.
Place P12 between the plates, position at the chosen angle,
fasten with M10x30 screws and secure with M6x30 screws.
PNI-P12TO2L15 frame tilt
P12
Holes 1
Holes 2
Holes 3
Holes 4
Holes 5
Holes 6
Holes 7
Holes 8
Holes 9
0°
6.5°
4.5°
2.5°
0.5°
-2°
-4°
-6°
-9°
-11°
-15°
6.5°
4.5°
2.5°
0.5°
-2°
-4°
-6°
-9°
-10.5°
-25°
7°
5°
2.5°
0.5°
-2°
-4°
-6°
-9°
-10.5°
-35°
7.5°
5.5°
3°
0.5°
-1.5°
--3.5°
-6°
-8.5°
-10°
-45°
8°
6°
3.5°
1°
-1°
-3°
-5.5°
-8°
-10°
-55°
8.5°
6°
3.5°
1°
-1°
-3°
-5.5°
-8°
-10°
Note 1 : Holes 1 are those toward F.O.H.
Note 2 : All angles measurements have been done without cables weight.
Note 3 : Angles are in relation to Horizontal position ( 0° )

PAGE 4 OF 4
- Read this document before using.
- Keep this document.
- Observe all warnings and cautions.
Standard inclinations :
0°
-15°
-25°
-35°
-45°
-55°
•NEXO cannot accept responsibility for accidents caused by any factor other than defects in this product itself.
•Please check the web site nexo-sa.com for the latest update.