Nokia OZO camera User manual

MAKING VIRTUAL REALITY

Index
Box Content 4 - 5
WARNINGS
Ventilation 7
Overheating 8
Operating and Storage Temperature 9
Protective Cover 10
Safety and Handling 11
General Warnings 12 - 13
BASICS
Device Handling 15
Mounting 16
Changing the Tripod Adapter 17
Connector Cap Removal 18
Connecting SDI 19
Connecting Power 20
Cartridge Replacement 21
Charging Battery 22
Extracting Data 23
OZO Applications 24
Basic Operation 25 - 26
WARRANTY AND LEGAL
Warranty 28 - 29
Regulatory and Safety Notices 30 - 31
Recycling 31

Box Content
11 12
10
8
2
1
4
9
The Protective NANUK 950 carrying case is intended for normal transportation
of OZO and included accessories. Please keep the cardboard shipping box and
packing, and reuse when transporting the camera by courier or shipping agent.
7 6
3
5

1. ProtectiveCover(comesttedtocamera)
2. Largetripodadapter(comesttedtocamera)
3. OZO Professional VR Camera PC-01
4. 3G-SDI adapter card in protective ESD bag, for external recording/
monitoring
5. T6 tool, for removing Connector Cap of power/SDI slot
6. Digital Cartridge DC-01, including 33Wh Li-Ion rechargeable battery
7. Media Module MM-01, including 500GB solid state storage
8. Docking Station DS-01, for battery charging and data transfer
9. Media Cable MC-01, for USB3 data transfer to computer directly from Media
Module or cartridge in Docking Station.
10. Small tripod adapter
11. Camera External AC power supply and AC cables
12. Docking Station AC power supply and AC cables
NOTE:Duetothesizethecaseshouldtravelasholdluggagewhenyingwith
OZObutthecartridges(containingLi-Ionbatteries)shouldberemovedand
carried as hand luggage according to international regulations.
5

WARNINGS

Ventilation
Do not cover the ventilation opening
(A).
TheDeviceiscooledbyairowing
between the outer and inner
structure.
Keep the device ventilation upright
(B).
Covering the opening or mounting
the device in a way that the
openings are not vertically on top
of each other would prevent the air
fromowing.
7
B
A

Overheating
Capture or broadcast will stop on
overheat
The Device is protected against
overheating by switching to standby
when the temperature of the device
exceeds a set limit (A).
Switching to standby discontinues any
kind of capturing because the sensors
are powered down.
If the temperature continues to
rise even after switching to standby
a second threshold triggers full
shutdown (B).
Do not use near heat sources or in a
space with insucient ventilation.
These may cause the device to
overheat, and stop capture.
Direct sunlight may also cause the
device to heat up more quickly.
8
BA

Operating and Storage Temperature
Operating Temperature
The device should only be used
between +32°F and +86°F (0°C and
+30°C).Donotuseoutsidethisrange.
Storage Temperature
The device should be stored between
-4°Fand+122°F(-20°Cand+50°C).
Do not store outside this range.
9
+32°F / +86°F 0°C / +30°C
-4°F / +122°F -20°C / +50°C

Protective Cover
Do not remove the protective cover
until the device is fully mounted.
Keeping the protective cover on
the device for as long as possible
decreases the risk of lens damage
signicantly.
To remove or attach the cover, open
it only the necessary amount.
Avoid contact with the lenses as
much as possible.
1
10
2 2

Safety and Handling
Handle with care
Thedeviceweightis4.2kg(9.3lbs)
including the digital cartridge.
Do not lift the device by holding the
protective cover or cartridge.
Do not manipulate the device without
the protective cover.
Care should be taken when moving
the device.
Do not place or mount the device on
unstable objects.
To avoid damage to the device,
remove and insert the Digital
Cartridge according to the
instructions given in the section
“Cartridge replacement” p. 21.
To avoid damage to the 3G-SDI card,
attach and remove SDI cables according
to the instructions given in the section
“Attaching SDI DIN cable” p. 19.
Mount correctly
The device must be mounted
securely before use according to
the instructions given in the section
“Mounting” p. 16.
Failure to mount securely could cause
damage to the device, or injury.
Specictoolsandthecorrectamount
of torque must be used when
changing the tripod adapter.
Do not place or mount the device on
vibrating or oscillating objects as this
may cause mechanical failure.
11

General Warnings
Do not drop the device
If the device is dropped, it may be
damagedormodiedexternallyor
internally and become unusable for
the intended purpose.
After dropping, in case of damage or
incorrect operation, please contact
themanufacturerfor(non-warranty)
repair. Take care to avoid injury if glass
lenses become broken.
Battery
Do not disassemble or open, crush,
bend or deform, puncture, or shred.
Do not modify or remanufacture,
attempt to insert foreign objects into
the battery, immerse or expose to
water or other liquids, or expose to
re,explosion,orotherhazard.
Only use the battery for the system
forwhichitwasspecied.
Only use the battery with a charging
systemthathasbeenqualiedforuse
withthesystem.Useofanunqualied
battery or charger may present a risk
ofre,explosion,leakage,orother
hazard.
Do not short circuit a battery or allow
metallic or conductive objects to
contact the battery terminals.
Please contact the manufacturer for
(non-warranty)repairtoreplacethe
battery with another battery that has
beenqualiedwiththesystem.Useof
anunqualiedbatterymaypresenta
riskofre,explosion,leakage,orother
hazard.
Do not insert a fully charged battery
into the charger repeatedly. Due to
the high initial charge, the battery
could be overcharged which could lead
to damage to the battery and to the
battery charger.

Promptly dispose of used batteries in
accordance with local regulations.
Battery usage by children should be
supervised.
The battery should only be charged
or used by a compatible device or
charger, and will fail to operate if
inserted to an incompatible system.
Avoid dropping the battery. If the
battery is dropped, especially on
a hard surface and you suspect
damage, take it to a service center
for inspection. Improper battery use
mayresultinare,explosion,orother
hazard.
Water / humidity
Do not use in or near water. The
device is not waterproof, and may be
damaged if used underwater, in rain,
or in environments with high moisture
or humidity.
Repairs / opening the device
Repairs should be performed only by
qualiedservicepersonnel.Donot
attempt to open the device, as this
may cause damage which will void the
warranty.
Power source
Use only the supplied power sources.
Take precautions when handling
power plugs. Do not use with power
outlets or extension cords if they are
overloaded, dusty, wet or physically
damaged.
Cables
Do not use the supplied USB cable to
directly connect two computers, as
this may cause damage. Do not walk
or step on cables. Do not place heavy
objects on cables. Do not twist cables.
13

BASICS

Device Handling
This is the most reliable way of
handling the device.
Lift the device at the “tail” applying
armandsafegrip.
Additionally you can hold the device
by the OZO Tripod adapter if it is
properly attached.
15

Mounting
Securely mounting a base plate
(A) to the tripod adapter (B) is
recommended.
The Device is delivered with the large
OZO Tripod adapter attached.
The large OZO tripod adapter
includes 5 x standard 3/8” tripod
mounting hole.
The included alternative small OZO
tripod adapter includes 1 x standard
3/8” tripod mounting hole.
B
A
16

Changing the Tripod Adapter
Specic force is required to ensure
the newly-attached tripod adapter is
securely xed.
1. Carefully remove the mounted
adapter (A) using an M8 tool.
2. Attach the alternative adapter (B).
3. Apply exactly 20 Nm with a
torquewrenchtoolandx
securely. Do not overtighten.
Do not replace the M8 screw.
If damaged, always replace with
original spare parts.
17
A
B

Connector Cap Removal
For streaming data through SDI and
supplying external power, remove
the connector cap (A) located below
the “tail” section by using the
provided T6 Torx tool.
For stand alone use, place the
connector cap back in the slot and
tighten by hand without excessive
torque.
This cap provides basic sealing and
protection for the SDI and power
connectors.
18
A

Connecting SDI
Attaching 3G-SDI card
Carefully remove the 3G-SDI SFP+
card (A) from the ESD bag, and insert
itrmlyintotheSFP+socket(B).
To remove, lift the latch (C) on the SDI
card and carefully apply backwards
pressure to the frame of card, NOT to
the DIN sockets.
Attaching SDI DIN cable
Attach a standard SDI DIN connector
(D) to the lower DIN socket shown by
arrow facing away from device.
To remove the cable, lift the cover
of the DIN connector, and apply
pressure.
Take care not to apply lateral force to
the DIN sockets. Use cable strain relief
where necessary, otherwise damage
may occur.
19
B
C
A
D

Connecting Power
Insert the external power plug into
the device rmly, and rotate the lock
ring (A) clockwise until it is tight.
Always ensure the external plug is
fully inserted, otherwise the device
may not power up, or may use
battery power only.
The socket-outlet shall be installed
near the equipment and shall be
easily accessible.
20
A