One Stop Systems Max Express OSS-lanPMC-4GC User manual

One Stop Systems, Inc. OSS-lanPMC-4GC User Manual
Rev. A
OSS-lanPMC-4GC
2235 Enterprise Street, Suite 110
Escondido, CA 92029
Phone: [phone]
Fax: [phone]
www.onestopsystems.com
Four Port Gigabit PMC Adapter

One Stop Systems, Inc. OSS-lanPMC-4GC User Manual
Rev. A 2
Description
The OSS-lanPMC-4GC is a four port (Quad) Gigabit Ethernet over Copper PMC module. This design facilitates a computer system
to communicate via four Ethernet ports at 10/100/1000 Mbit/sec rate. Attached to the OSS-lanPMC-4GC PCB is a PMC bezel with a
custom stamp out to accommodate four RJ45 modular connectors and four bi-color LEDs. The OSS-lanPMC-4GC offers four ports
of either 1000, 100 or 10 MHz connectivity providing clear-channel communication. Frames are transferred between theGigE ports
and a 33/66-MHz, 64-bit host PCI bus.
Initial Set-Up
Unpacking Instructions
1. If the carton is damaged when you receive it, request that the carrier's agent be present when you unpack and inspect the
equipment.
2. After unpacking, verify that all items listed in the packing list are present.
3. Inspect the equipment for shipping damage.
4. Save all packing material for storage or return shipment of the equipment.
5. For repairs or replacement of equipment damaged during shipment, contact One Stop Systems, Inc. to obtain a Return
Materials Authorization (RMA) number and further shipping instructions.
PMC-Pn1
Intel 82546EB
Controllers
PMC-Pn3
4X Bi-color
LED
PMC-Pn2
RJ45 Connectors
PCI-PCI
Bridge

One Stop Systems, Inc. OSS-lanPMC-4GC User Manual
Rev. A 3
Installation and Removal
1. Power down the host system.
2. Open the chassis according to your system documentation.
3. Let the power supply cool down, if necessary.
4. Remove the host board from the system.
5. Remove the OSS-lanPMC-4GC from the protective bag, observing proper ESD safety procedures.
Installing the OSS-lanPMC-4GC:
1. Press the OSS-lanPMC-4GC bezel into the cutout in the PTMC carrier I/O panel. The gasket around the OSS-lanPMC-
4GC bezel makes a tight fit to ensure an electromagnetic seal. Check that the bezel and gasket are pressed firmly into the
carrier I/O.
2. Press the OSS-lanPMC-4GC down onto the carrier so PN1–PN3 plug into JN1–JN3 on the PMC carrier.
3. Install four screws to secure the board in place
Installation Diagram
.
Screw
OSS-lanPMC-4GC
OSS-lanPMC-4GC
PMC Carrier Card
PMC Carrier Card
Screw

One Stop Systems, Inc. OSS-lanPMC-4GC User Manual
Rev. A 4
Specifications
Electrical/Mechanical Specifications
Form Factor:
64 bit, 33/66 MHz PMC interface (PCI Rev 2.2), 3.3V Signaling, 5V tolerant
Dimensions (H x L):
5.86 x 2.91 inches (148.8 x 73.9mm) (See component height section below)
Front Panel Connectors:
Four RJ45 connectors
Front Panel Indicators:
4X Bi-color LED
Power Consumption (designed to meet the following conditions
9.48W typical @ 3.3V [Note that this is higher than the 7.5W PMC spefication]
Operating Environment (designed to meet the following conditions)
Temperature Range:
-5° to 55°C (23° to136°F)
Relative Humidity:
20 to 80% non-condensing
Shock:
30g acceleration peak (11ms pulse)
Vibration:
5-17 Hz 0.5” double amplitude displacement; 7-2000Hz, 1.5g acceleration.
Agency Compliance Designed to meet, but not tested
Pending
Component Height
Due to the density of the OSS-lanPMC-4GC design it is not possible to conform to the PMC component height restrictions. The
height envelop (dotted line in the Figure) will be violated by approximately 0.040” next to the I/O space

One Stop Systems, Inc. OSS-lanPMC-4GC User Manual
Rev. A 5
Block Diagram
Busmode Pins
Since OSS-lanPMC-4GC supports only the PCI bus protocol at the PMC connectors, the BUSMODE1# pin is asserted LOW for two
reasons only; (1) to indicate its presence to the host, and (2) to indicate that it is capable of performing PCI Bus protocol. The
OSS-lanPMC-4GC responds within ten PCI clock cycles after detecting the state of BUSMODE[4:2]# pins.
BUSMODE[4:2]# state (input)
Mode
BUSMODE1# output state
Response explanation
000
“Card Present” test.
0
“Card Present” mode.
No bus protocol is used and
card is held in reset
001
Return Card Present
0
Capable of performing
if PCI capable and
PCI protocol.
uses PCI protocol.
All other states
-
1
Card held in reset.

One Stop Systems, Inc. OSS-lanPMC-4GC User Manual
Rev. A 6
PMC Voltage Keying
The PCI-to-PCI bridge is capable of operating in either 3.3-volt or 5-volt signaling environments. Therefore, both voltage keying
holes are provided on the PCB as shown in Figure 1. When installing the card on a host, the voltage coding key (on the host) must
be installed in accordance with the host requirements. Note that 66MHz operation is only defined for 3.3-volt signaling.
Ethernet Controller
Intel 82546EBis a Dual Port Gigabit Ethernet Controller in a single, compact component with two fully integrated Gigabit Ethernet
MAC and PHY functions. The controller is capable of transmitting and receiving two channels of data at rates of 1000 Mbps, 100
Mbps, or 10 Mbps. It has a 64-bit wide PCI 2.2 compliant interface capable of operating at up to 66MHz (PCI-X 133MHz though
supported by the device is not supported on this design). The device is in a 364 ball 1mm pitch BGA package. Two of these devices
are used to implement the four ports of 10/100/1000BASE-T
The 82546EB have a System Management Bus (SMB) interface and Serializer/Deserialzer interface. These interfaces are not used
on OSS-lanPMC-4GC.
LEDs
There is a 4X Bi-color LED on the front, with one LED for each port. When a LINK is asserted the green LED will be turned on.
When there is activity the yellow LED will be turned on. If there are continuous periods of activity, the green and yellow LEDs will
alternate.

One Stop Systems, Inc. OSS-lanPMC-4GC User Manual
Rev. A 7
Connectors (continued)
Communication on the host PCI bus is done across two PMC connectors, Pn1 and Pn2.
The OSS-lanPMC-4GC can use the Pn4 connector for rear I/O.
Pn1 32-bit PCI
Pn2 32-bit PCI
Pn3 64-bit PCI
Pin
#
Name
Name
Pin
#
Pin
#
Name
Name
Pin
#
Pin
#
Name
Name
Pin
#
1
TCK
-12V
2
1
+12V
TRST#
2
1
PCI-
RSVD
Gr ound
2
3
Gr ound
INTA#
4
3
TMS
TDO
4
3
Gr ound
C/BE[7]#
4
5
INTB#
INTC#
6
5
TDI
Gr ound
6
5
C/BE[6]#
C/BE[5]#
6
7
BUSMODE1#
+5V
8
7
Gr ound
PCI-RSVD
8
7
C/BE[4]#
Gr ound
8
9
INTD#
PCI-
RSVD
10
9
PCI-RSVD
PCI-RSVD
10
9
V(I/O)
PAR64
10
11
Gr ound
3.3Vaux
12
11
BUSMODE2#
+3.3V
12
11
AD[63]
AD[62]
12
13
CLK
Gr ound
14
13
RST#
BUSMODE3#
14
13
AD[61]
Gr ound
14
15
Gr ound
GNT#
16
15
+3.3V
BUSMODE4#
16
15
Gr ound
AD[60]
16
17
REQ#
+5V
18
17
PME#
Gr ound
18
17
AD[59]
AD[58]
18
19
V(I/O)
AD[31]
20
19
AD[30]
AD[29]
20
19
AD[57]
Gr ound
20
21
AD[28]
AD[27]
22
21
Gr ound
AD[26]
22
21
V(I/O)
AD[56]
22
23
AD[25]
Gr ound
24
23
AD[24]
+3.3V
24
23
AD[55]
AD[56]
24
25
Gr ound
C/BE[3]#
26
25
IDSEL
AD[23]
26
25
AD[53]
Gr ound
26
27
AD[22]
AD[21]
28
27
+3.3V
AD[20]
28
27
Gr ound
AD[52]
28
29
AD[19]
+5V
30
29
AD[18]
Gr ound
30
29
AD[51]
AD[50]
30
31
V(I/O)
AD[17]
32
31
AD[16]
C/BE[2]#
32
31
AD[49]
Gr ound
32
33
FRAME#
Gr ound
34
33
Gr ound
PMC-RSVD
34
33
Gr ound
AD[48]
34
35
Gr ound
IRDY#
36
35
TRDY#
+3.3V
36
35
AD[47]
AD[46]
36
37
DEVSEL#
+5V
38
37
Gr ound
STOP#
38
37
AD[45]
Gr ound
38
39
Gr ound
LOCK#
40
39
PERR#
Gr ound
40
39
V(I/O)
AD[44]
40
41
PCI-RSDV
PCI-
RSVD
42
41
+3.3V
SERR#
42
41
AD[43]
AD[42]
42
43
PAR
Gr ound
44
43
C/BE[1]#
Gr ound
44
43
AD[41]
Gr ound
44
45
V(I/O)
AD[15]
46
45
AD[14]
AD[13]
46
45
Gr ound
AD[40]
46
47
AD[12]
AD[11]
48
47
M66EN
AD[10]
48
47
AD[39]
AD[38]
48
49
AD[09]
+5V
50
49
AD[08]
+3.3V
50
49
AD[37]
Gr ound
50
51
Gr ound
C/BE[0]#
52
51
AD[07]
PMC-RSVD
52
51
Gr ound
AD[36]
52
53
AD[06]
AD[05]
54
53
+3.3V
PMC-RSVD
54
53
AD[35]
AD[34]
54
55
AD[04]
Gr ound
56
55
PMC-RSVD
Gr ound
56
55
AD[33]
Gr ound
56
57
V(I/O)
AD[03]
58
57
PMC-RSVD
PMC-RSVD
58
57
V(I/O)
AD[32]
58
59
AD[02]
AD[01]
60
59
Gr ound
PMC-RSVD
60
59
PCI-
RSVD
PCI-
RSVD
60
61
AD[00]
+5V
62
61
ACK64#
+3.3V
62
61
PCI-
RSVD
Gr ound
62
63
Gr ound
REQ64#
64
63
Gr ound
PMC-RSVD
64
63
Gr ound
PCI-
RSVD
64

One Stop Systems, Inc. OSS-lanPMC-4GC User Manual
Rev. A 8
Limited Warranty
One Stop Systems warrants this product to be free of defects in material and workmanship for an initial period of two years from
date of delivery to the original purchaser from One Stop Systems.
During this period, One Stop Systems will, at its option, repair or replace this product at no additional charge to the purchaser,
except as set forth in this warranty agreement.
One Stop Systems will, at its option, repair or replace this product at no additional charge to the purchaser, if the defect is related to
the One Stop Systems manufactured product, such as a power supply, backplane, other chassis components or CPUs. One Stop
Systems is not liable for any defects in material or workmanship of any peripherals, products or parts, which One Stop Systems
does not design or manufacture. However, One Stop Systems will honor the original manufacturer’s warranty on these products.
One Stop Systems will analyze the defective component and the customer will be charged in the following instances:
No problem found: $75 (U.S. dollars).
Damage: Parts and labor at $75 per hour with a $100 minimum charge (U.S. dollars). Receipt of damaged goods voids the One
Stop Systems warranty.
Repair parts and replacement products will be furnished on an exchange basis and will be either new or reconditioned. All
replacement parts and products shall become the property of One Stop Systems, if such parts or products are provided under this
warranty agreement. In the event a defect is not related to theOne Stop Systems manufactured product, One Stop Systems shall
repair or replace the defective parts at the purchaser’s cost and deliver the defective parts to the purchaser.
This limited warranty shall not apply if the product has been misused, carelessly handled, defaced, modified or altered, or if
unauthorized repairs have been attempted by others. The above warranty is the only warranty authorized by One Stop Systems and
is in lieu of any implied warranties, including implied warranty of merchantability and fitness for a particular purpose. In no event will
One Stop Systems be liable for any such damage as lost business, lost profits, lost savings, downtime or delay, labor, repair or
material cost, injury to person or property or any similar or dissimilar consequential loss or damage incurred by the purchaser, even
if One Stop Systems has been advised of the possibility of such losses or damages.
In order to obtain warranty service, the product must be delivered to the One Stop Systems facility, or to an authorized One Stop
Systems service representative, with all included parts and accessories as originally shipped, along with the proof of purchase and
a Returned Merchandise Authorization (RMA) number.
The RMA number is obtained, in advance, from One Stop Systems Customer Service Department and is valid for 30 days. The
RMA number must be clearly marked on the exterior of the original shipping container or equivalent. Purchaser will be responsible
and liable for any missing or damaged parts. Purchaser agrees to pay for shipping charges one way, and to either insure the
product or assume the liability for loss or damage during transit. Ship to:
One Stop Systems
ATTENTION: RMA REPAIR DEPARTMENT
RMA ####
2235 Enterprise Street, Suite 110
Escondido, CA 92029
www.onestopsystems.com
2235 Enterprise Street, Suite 110 Escondido, CA 92029 Tel [phone] Fax [phone]