Onean Carver User manual

WARNING!
The practice of jet powered watersports can be dangerous if the necessary
precautions are not taken. For this reason, we have prepared this user manual.
It will help you to know your new Carver board and to use it correctly.
It contains information related to the assembly, care, use and maintenance of
your Carver board. Please read this manual carefully before using the equipment.
It is the responsibility of the user to take the necessary measures for a safe use of the
products from Aquila Boards. The company will not be responsible for any damages
that may arise from the improper use of the equipment as well as its deterioration
due to incorrect maintenance.
!

Last update: 2017/07/11
This user’s manual is subject to be changed due to potential modifi cations
in design.

CARVER USER’S MANUAL 5
It is important to get familiar with the board’s security systems before starting
enjoying it. Please make sure you use the board following the instructions
provided in this manual.
• Always check the unit before entering the water. Make sure the
board, the safety disconnection system, the battery and the wireless
controller are in good condition.
• Do not lend your equipment to anyone who has not been instructed
in the use of the Carver.
• When entering the water, you must avoid entering through wave break
areas and in case of doing so, you must always place yourself between
the board and the wave. This way the board will not harm you in case a
wave strikes you.
• Never practice this sport if the conditions exceed your skill level.
• Always wear the Leash attached while using the unit.
• When getting on the board you must always do it from one side, even
in areas of high depth. The water jet has great power and could cause
injuries.
• Never place your hands or feet near the impeller. The suction force
from the jet is very powerful and it could drag them to the interior. Even
with the battery disconnected you must be aware of the impeller since
the leading edges are sharp and may cut.
• You must take into account that the board does not have a braking
system. Although you may discontinue to press the throttle, the board
will continue moving forward due to its inertia. This route can be relatively
long if you want to move from the glide status to the stopping one. It is
recommendable to slow down as you approach the target area where
you want to stop.
• Do not touch the steel tube right after use since it could be at elevated
temperature.

CARVER USER’S MANUAL
6
The following describes a list of the components included with the equipment
and a description of them.
Construction with EPS core and laminated fi breglass and epoxy full sandwich.
• Weight (without the battery): 13kg / 28.6lbs
• Length: 240cm / 7´8”
• Width: 70cm / 27.7”
• Thickness: 15cm / 5.9”
• Volume: 170L

CARVER USER’S MANUAL 7
• Nominal power: 5KW
• Nominal voltage: 44,4 VDC
• Static push: 240N
Short circuit, overcharge and temperature
protection. Waterproof.
• Type: multicell Litio-Ion
• Weight: 12,5kg / 26.5lbs
• Max. electric discharge: 130 A.
• Nominal capacity: 40.0 Ah
• Nominal voltage: 44.4V
Over voltage protection. Thermal
protection. Short circuit protection. Reverse
polarity protection. Charging indicator.
• Input power: 220-230Vac (*Also
available 110Vac)
• Charging current: 15 Amps
• Output voltage: 50,4 Vdc
Watertight. Thrust display. Battery display. Pressure
sensor Drop. Induction charging.
• Frequency: 2.4Ghz
• Battery: LiPo 300mAh
Qi inductive technology charger that simplifies
charging into just setting your controller down on
the charging pad. Input:5V-2A, Output: 5V-1A.
Pre-formed arch prevents collapsing. 7mm neoprene
padding. Internal adjustment system. Twist control
system.
7-Foot Coiled leash. Padded neoprene cuff . Stainless
steel swivels to stop tangles. Custom made security
magnet pull system.
Hard plastic and fi ber 6,5 inch UsBox fi ns.
SYNC BATTERY

CARVER USER’S MANUAL
8
1. Insert the fin inside the finbox as
shown in the picture.
2. Insert the metallic square
in the finbox and move
it until it alignes the screw.
3. Fix the screw attaching the fin to the
board.
1. Insert the screw through the insert and hold the leash.
2. Align the holes with the leash insert located on the left hand lower side of
the board on the non-slippery surface.
3. Screw the piece to secure it.
Leash insert
Leash insert
Leash screw
Screw
insert

CARVER USER’S MANUAL 9
Before using the unit for the first time, the cylindrical magnet must be
inserted in the hole inside the battery compartment.
The board incorporates inserts valid for both goofy and regular riders.
1. Depending on the style of riding, place the footstraps over the desired
inserts. One on the front of the board and one on the back.
2. Place the screw through the screw insert and hold the footstrap.
3. Align the holes with the footstrap insert.
4. Screw the footstrap to secure it.
Footstraps
inserts
Footstrap insert
Footstrap screw
Screw
insert
Battery magnet
Battery compartment
Insert for the
battery magnet

CARVER USER’S MANUAL
10
• In order to travel with the board, the battery must be below 30% of charge.
This means that the LED bar must be only showing one LED.
Placing the drop near the battery display you will be able to check the
battery level.
• Do not transport the battery inside the board unless you intend to use
it inmediately. Always use the side handle to transport the battery pack.
Do not pick it up by the top handle.
• Between uses you should store the battery between 0ºC y 40ºC (32°F a
104°F) always less than 3 months, in a ventilated area and with a humidity
between 0% - 80%. Do not store the battery near metallic objects.
Always charge the battery and remote to the fullest before operting the
equipment.
Connection and disconnection of the battery:
1. Check the watertight seal and the battery housing to make sure they are
clean and free of sand. Make sure there aren´t any signs of damage before
use. Make sure there isn´t any water inside the battery compartment.
2. Turn the vent one full round counter-clock wise. Place the battery
on the pad, near the battery compartment where the battery must
be placed. Once the battery is placed
on the pad, grab it by the upper handle
and place in the battery compartment.
The blue LED on the front of the board
will light up indicating the connection.
Display Battery percentage
20%
40%
60%
80%
100%
Drop
Sensor
Battery level
indicators
Battery Connectors
SYNC BATTERY

CARVER USER’S MANUAL 11
3. Make sure the four pins are not visible and be aware of the positioning
while inserting it. Only one way is possible
according to its geometry.
4. After inserting the battery turn it
180º clock wise and fold it until
it is on the same level as the board.
In case that the handle doesn´t turn easily, press down on the
battery to help the watertight seal to compress. Please make
sure that the sign (unlocked) is not visible after locking the
battery.
5. Close the vent completely, turning it clock wise to assure watertightness.
6. In order to ease the extraction of the battery, turn the vent one full round
counte-clock wise and turn the handle counter-clock wise as well. Pull
from the upper handle perpendicularelly to extract the battery.
7. Keep the vent always closed in any other moment
and do not turn it more than three full turns.
Side
Handle
Upper Handle
Battery
Compartment
Board
Connectors
O
Antenna’s LED
OPEN CLOSED

CARVER USER’S MANUAL
12
WARNING!
Always connect the charger to the wall outlet fi rst and then to the
battery.
It is extremely important to respect the colors when connecting the
cable to the battery. Reverse polarity could have some devastating
consequences for the battery.
1. In order to charge the battery it must be taken our from the board.
2. Insert the connector to the battery respecting the colors as shown in the
previous drawing (red with red and black with black).
3. When connecting the charger to the battery, The LEDs will
light up indicating a successful connection. In case of the
LEDs not lighting up, please make sure that the charger
is properly plugged to the wall outlet and to the battery.
4. Once the battery is connected, the display LED
indicator will light up indicating the charge (img.
A) until fully charging it, turnining to green (img. B).
5. The LEDs in the battery will progressively light
up as the battery is being charged.
6. When the battery is fully charged the LEDs will turn off and
you must proceed to disconnect the battery.
!
Frontal View Back View
On/Off Indicator
AC Cable
DC Cable
Charge indicator
Led connection
indicator
Led connection
indicator
Led charging
indicator
Led charging
indicator
¨A¨Charging B Full charge
Charge
Indicators
Connector
Body
Input battery
connectors

CARVER USER’S MANUAL 13
Avoid pulling from the cable, always pull
from the connector body.
Always supervise the charge, do not leave
the battery unnatended while charging.
• The battery does not need to be fully discharged before charging. A
Lithium.Ion battery doesn´t have memory effect. This means that the
maximum energy capacity won´t be aff ected if its charged after not being
fully discharged.
• Make sure that the battery does not remain to be connected to the
charger after the charge has been completed.
• Always remember to close the battery rubber connector covers before
use.
• The temperture use for the battery must always remain between 0ºC y
60ºC (32ºF y 140ºF).
• Extreme temperatures will aff ect the battery life, specially during charge.
Avoid charging the battery while being exposed to direct sunlight or
extreme high or low temperatures. The charge is recommended to be
carried out with temperatures (between 10ºC y 45ºC / between 50ºF y
113ºF).
To activate the board you must press on the drop. The power of the Jet will
depend on the amount of pressure done on the drop.
Through the wireless controller you can set the maximum power for the Jet
and also adjust diff erent profi les.
In order to access the configuration menu, you must follow the following
indications. Always with the battery initially disconnected:
1. With the controller totally off (no LEDs ) place
the drop over the logo.
2. On this position, press on the drop
until the fi rst LED of the board display
SYNC BATTERY
Drop
Sync
Controller
battery
Board Battery
Power
Indicators
SYNC BATTERY
1
Connector
body
Cable

CARVER USER’S MANUAL
14
on the controller beings to blink. At
this moment, the LED bar will begin to
progressively light up. Each position
represents a different function.
Once the fi rst LED begins to blink, you
must press on the drop again to access the submenu.
In this submenu, the controller will begin to search for a board for a few
seconds and the sync LED will begin to blink.
As the sync LED is blinking the battery must be inserted to complete
the synchronization (see 4.1.2.).
Once the board is synched, both LEDs will blink at a higher pace
indicating that the process has been successfully completed.
Once that the fi rst two LEDs are fl ashing
you must press on the drop to access this
submenu.
The power bar will progressively light up. Press on the drop
to set the desired value according to the following description.
Once the fi rst three LEDs are fl ashing you must press on the drop to
access the submenu.
The power bar will progressively light up. Press on the drop to set
the desired value according to the following description.
• 1 LED: Staggered 1.
• On this profile we have discretized the power levels of
the jet in 5 different ranges of pressure on the drop. It
allows us to control and hold the pressure on each range.
SYNC BATTERY
LED Blinking
2
SYNC BATTERY
LEDs Power [W] Display
1 LEDs 800
2 LEDs 1.200
3 LEDs 2.600
4 LEDs 3.700 Factory Settings
5 LEDs 5.000
Low
0
20
40
60
80
100
Medium High
Staggered 1

CARVER USER’S MANUAL 15
• 2 LEDs: Staggered 2. This profi le has three power levels. The
fi rst one allows us to activate the jet at a low power in order to go at
slow speeds (for example, to go from shore to a safe cruising area). The
second power level will allow us to decrease the power consumption
once planing is reached so we can get more battery life.
• 3 LEDs: Staggered 3. This is a profi le similar to the previous
one with the difference that the second power level is at a higher
power. In case that ¨Staggared 2¨doesn´t allow us to reach planing we
could use this one.
• 4 LEDs: 100%/0%. The jet will from 0 to 100% power
by pressing on the drop. This will be the most confortable
setting for those wanting maximum power thrughout
the ride but the battery life will be compromised.
• 5 LEDs: lineal. On this profile, the jet reacts
lineally to the pressure on the drop. It requires a bit more
of skills in order to use the entire range appropriaetly.
Low
0
20
40
60
80
100
Medium High
Staggered 2
Pr
Low
0
20
40
60
80
100
Medium High
Staggered 3
Low
0
20
40
60
80
100
Medium High
Staggered 4
Low
0
20
40
60
80
100
Medium High
Staggered 5

CARVER USER’S MANUAL
16
3. Once the controller has reached all 4 LEDs, all
the information will be stored and all LEDs turn off .
If you do not want to change any of these parameters you don’t need
to do this process again, it will remain in the internal memory of the
controller.
4. To check the current status you can repeat the step 1 but press on the
drop only one time instead of holding it pressed. The controller will show
the preferences for each category.
5. Always use the controller inside the controller wristband.
6. Always secure the wirstband before use.
7. In order to activate the jet, press on the drop with the index fi nger and
thumb.
8. The power will vary depending on the pressure placed on the drop.
1. Connect the Qi charger through a USB.
2. Place the controller on the center of the Qi as shown in the drawing
below.
3. When charging, the green LED will begin to blink.
4. Once the controller is fully charged, the LED will turn off .
5. To check the status of the battery of the controller please pick it up and
press on the drop to see the battery LED-.

CARVER USER’S MANUAL 17
1. Attach the leash right below the knee of the front leg, as shown on the
drawing below.
2. Once the rider is ready to use the board,
place the security magnet key on the board.
The magentic key is a security mechanism, the jet will not activate if this
key is not properly placed.
3. In case of fall, the magnetic key will detatch, stopping the jet. Once the
rider is back on the board ready to continue its use, the magnetic key
should be properly placed again.
The board has various security mechanisms that stop it automatically in case
of:
• Engine overheat.
• Battery overheat.
• Loss of communication between the controller and board.
• Tightening of the jet when starting or blockage of the turbine due to an
external object.
• Magnetic key disconnection. In case of fall, it will automatically disconnect.
• In case of fall, or if the controller is submerged, the jet will stop as a
security measure.
If any of the previous cases happes during use, the jet will automatically stop.
This security block will remain until the above causes are solved.
In order to reactivate the board, the security magnet must be disconnected
and reconnected.
Magnetic Key
Magnetic Key
Connector

CARVER USER’S MANUAL
18
• The Carver board is suitable for fresh ans salt water use. Ideal conditions
are with no wind and fl at water.
• Be aware of local regulations before using and the areas where this kind
of equipment is eligible for use.
• Taking into account that the jet sucks water through the intake it is
important to look for waters free of fl oating elements at which to practice
this sport. Mentioned floating elements could cause damage to the
rotating elements inside the waterjet.
• The Carver Board has not been designed to be used at wave breaking
areas. Please look for an area of calm waters at which to entry the water.
• Taking into account the high speeds and maneuverability of the board, it
important to use the Carver at large open spaces free of obstacles.
• Be aware of the tides. With the sea level changes, new obstacles may
arise depending on the tide.
• Avoid using this product in the vicinity of other people, vessels or objects
that may compromise the user’s or board’s security.
• Avoid crowded beaches and always respect the navigation channels.
• In case of entering the water throught the beach, make use of the marked
areas that allow the entry and exit of watercrafts.
• It is advisable not to overturn/fl ip the board in the water.
• Do not grab or lift the board by the discharge connectors.
• Do not remove the goretex vent in the back of the board.
• Make sure the leash and the magnetic security key (kill switch) are in good
condition.
• Make sure the remote works properly before heading to the water.
• Make sure to assemble your equipment over grass or sand in order not
to damage it. Any damage caused by manipulating your equipment over
a hard and abrasive surface will not be covered by the warranty.

CARVER USER’S MANUAL 19
During fi rst uses it is recommendable to use it on your knees.
1. Get on top of the board with the leash attached and the magnetic
key connected. You should place your knees on each side of the front
footstrap.
2. After being positioned, press on the drop to activate the jet.The power
will vary depending on the pressure being put on the drop.
3. Once you gain speed you can progressively stand on it.
Make sure not to accidentally press on the drop while getting on or off
the board.
Before turning, make sure there is enough space to do so
and not interfere with the trajectory of any other vehicle.
Shift the weight towards the side where you intend to turn to ease the
movement. The more speed, the easier it is to turn. The board turns like a
conventional board.
• Do not activate the jet outside of the water. The propulsion system is
not meant to be used outside of the water, this could signifi cantly damage
the jet.
• After a long use going full thrust, it´s recommendable to wait at least one
minute for the jet not to overheat.
• When the jet reaches high temperatures, an inner fan is automatically
activated for heat dissipation purposes. In order for this process to be
done appropriately, the jet must be in contact with the water.
• It is not recommendable to step on the battery surface. Although
it’s designed to hold weight, when stepping on it, the watertight seal
compresses facilitating water to get in.

CARVER USER’S MANUAL
20
• This board could reach high speeds. It is recommendable to use a life vest
and a helmet while operating this product.
• Do not go further off shore than you can return swimming and always
have someone watching from shore. Do not operate this product alone.
• Be aware of climate changes or any other sudden change in the located
area (tides, shallow waters,..). Do not use this product while electric
storms.
• Do not use this product near swimmers or scuba divers.
• Make sure that the water is deep enough to operate this board, be aware
of coral reefs.
• Do not operate in areas of high current or waves. The Carver is not
meant to be used to surf waves. In case of being tilted by a wave, the
rider could suff er severe damages.
• Do not use behind another board. In case of doing it, make sure you
have enough space to turn in case the rider ahead falls.