Onean X User manual

WARNING!
The practice of jet powered watersports can be dangerous if the necessary
precautions are not taken. For this reason, we have prepared this user’s manual.
It will help you to know your new Onean X board and to use it correctly.
It contains information related to the assembly, care, use and maintenance of
your Onean X board. Please read this manual carefully before using the equipment.
It is the user’s responsibility to take the necessary measures for safe use of the Aquila
Boards’s products. The company will not be responsible for any damages that may
arise from the improper use of the equipment as well as its deterioration due to an
incorrect maintenance.
!

index
1. Main Security checkS................................5
2. Packing LiSt..............................................6
2.1. Onean X BOard ....................................6
2.2. Onean X Bag..........................................6
2.3. 2 Jet Units..............................................6
2.4. Batteries................................................6
2.5. Chargers................................................6
2.6. remOte COntrOl.....................................6
2.7 grease.....................................................6
2.8. QiCharger fOr the wireless COntrOller...7
2.9. statOr+nOzzle.......................................7
2.10. impeller................................................7
2.11. handle.................................................7
2.12. tOOling Kit..........................................7
2.13. trigger.................................................7
2.14. fOOtstraps...........................................7
2.15. leash + seCUrity Key .............................7
2.16. Us BOX fins.........................................7
FirSt aSSeMbLy...............................................8
3.1. insert the fins.........................................8
3.2. install the leash.....................................8
3.3. insert the Battery magnet....................... 9
3.4 insert female COneCtOrs...........................9
3.5. pOsitiOning the fOOtstraps.....................9
uSe and conFiguration oF the equiPMent...10
4.1. Batteries..........................................10
4.1.3 battery charge...............................12
4.2. wireless COntrOller .......................13
4.3. leash...............................................17
4.4. seCUrity meChanisms .......................17
5. SaFety guideLineS.................................18
5.1 terms Of Use ....................................18
5.2. BefOre getting intO the water ..........18
5.3. first Use .........................................19
5.4. getting OUt Of the water..................19
5.5. general seCUrity measUres ..............20
6. Maintenance oF the equiPMent..............21
6.1. BOard maintenanCe..........................21
6.2. Battery maintenanCe........................21
6.3. wireless COntrOller maintenanCe....22
6.4 Charger maintenanCe........................22
7. rePair and rePLaceMent oF coMPonentS...23
7.1. impeller ...........................................23
7.2. COnneCtOrs......................................25
8. diagnoSiS SySteM .................................26

ONEAN X USER’S MANUAL 5
01
Main Security checkS
1. Main Security checkS
It is important to get familiar with the board’s security systems before starting
to enjoy it. Please make sure you use the boards following the instructions
provided in this manual.
• Always check the unit before entering the water. Make sure the
board, the safety disconnection system, the batteries and the wireless
controller are in good condition.
• Do not lend your equipment to anyone who has not been instructed
in the use of the Onean X.
• When entering the water, you must avoid entering through wave
breaking areas and in case of doing so, you must always place yourself
between the board and the wave. This way the board will not harm you in
case a wave strikes you.
• Never practice this sport if the conditions exceed your skill level.
• Always wear the leash attached while using the unit.
• When getting on the board you must always do it from one side, even in
areas of high depth. The board’s jet is powerful and could cause injuries.
• Never place your hands or feet near the impeller. The suction force
from the jet is very powerful and it could drag them to the interior. Even
with the batteries disconnected you must be aware of the impeller since
the leading edges are sharp and may cut.
• You must take into account that the board does not have a braking
system. Although you may discontinue to press the throttle, the board
will continue moving forward due to its inertia. This route can be relatively
long if you want to move from the glide status to the stopping one. It is
recommendable to slow down as you approach the target area where
you want to stop.
• Do not touch the steel tube right after use since it could be at elevated
temperature.

ONEAN X USER’S MANUAL
6
02 Packing List
2. Packing LiSt
The following describes a list of the components included with the equipment
and a description of them.
2.1. onean X board
Construction with EPS core and laminated breglass
and epoxy full sandwich.
• Weight (without batteries): 23 kg / 50 lbs
• Length: 240 cm / 7´8”
• Width: 70 cm / 27.7”
• Thickness: 15 cm / 5.9”
• Volume: 150 L
2.2. onean X bag
• Semi rigid Onean Bag.
• Full bag inner padded reinforcement.
• Includes detachable wheels that ease
transporting.
2.3. 2 Jet unitS
• Nominal power: 10 kW
• Nominal voltage: 44,4 VDC
• Speed: 45 km/h
2.4. batterieS
Short circuit, overcharge and temperature
protection. Waterproof.
• Type: multicell Litio-Ion
• Weight: 14 kg / 30 lbs
• Max. electric discharge: 130 A
• Nominal capacity: 40.0 Ah
• Nominal voltage: 44.4 V
• IP68 Certied
2.5. chargerS
Over voltage protection. Thermal protection. Short
circuit protection. Reverse polarity protection.
Charging indicator.
• Input power: 220-230 VAC (*Also available 110
VAC)
• Charging current: 15 A
• Output voltage: 50,4 VDC
2.6. reMote controL
Watertight. Thrust display. Battery display.
Pressure sensor Drop. Induction charging.
• Frequency: 2.4 GHz
• Battery: LiPo 300 mAh
2.7 greaSe
Silicone grease (white) for battery connectors,
blue grease for mechanical maintenance.

ONEAN X USER’S MANUAL 7
02
Packing List
2.8. qicharger For the wireLeSS controLLer
Qi inductive technology charger that
simplifies charging into just setting your
controller down on the charging pad. Input:
5 V-2 A, Output: 5 V-1 A.
2.9. Stator+nozzLe
• Custom designed and CNC machined
out of high strength and corrosion
resistant tempered aluminum.
• Parts are hard anodized and xed joint
2.10. iMPeLLer
• 63.7 mm diameter. Custom designed
and CNC machined out of high strength
and corrosion resistant tempered
aluminum.
• Hard anodized, providing extra
corrosion resistance and an increased
surface hardness.
2.11. handLe
Made of highly durable thermoplastic
rubber, end webbing is doubled and
stitched for extra strength and security.
2.12. tooLing kit
• Contains conventional manual tools.
• Screw set and custom made tools necessary for
impeller extraction/insertion.
• All high strength and corrosion resistant.
• Ex. Impeller extractor tooling.
2.13. trigger
Ideal to minimize the eort of pressing the drop. Just
place the drop inside the trigger and press on it. Easy
to install, easy to remove.
2.14. FootStraPS
Pre-formed arch prevents collapsing. 7 mm neoprene
padding. Internal adjustment system. Twist control
system.
2.15. LeaSh + Security key
7-Feet Coiled leash. Padded neoprene cu. Stainless
steel swivels to stop tangles. Custom made security
magnet pull system.
2.16. uS boX FinS
Hard plastic and bre 6,5 inch Us Box ns.

ONEAN X USER’S MANUAL
8
03First Assembly
3. FirSt aSSeMbLy
3.1. inSert the FinS
1. Insert the fin inside the finbox as
shown in the picture.
2. Insert the metallic square in the nbox
and move it until it alignes the screw.
3. Fix the screw attaching the fin to the
board.
3.2. inStaLL the LeaSh
1. Insert the screw through the insert and hold the leash.
2. Align the holes with the leash insert located on the left hand lower side of
the board on the non-slippery surface.
3. Screw the piece to secure it.
Leash insert
Leash insert
Leash screw
Screw
insert

ONEAN X USER’S MANUAL 9
03
First Assembly
3.3. inSert the battery Magnet
Before using the unit for the first time, the cylindrical magnet must be
inserted in the hole inside the battery compartment. A sticker is provided
inside the magnet’s plastic bag that must be placed after inserting the
magnet. The entire space must be covered to avoid water inside the magnet
compartment.
3.4 inSert FeMaLe conectorS
Please, screw the female connectors, found in the wireless controller case,
in the holes of the bottom part of the battery using the tool provided on the
tooling kit.
3.5. PoSitioning the FootStraPS
The board incorporates inserts valid for both goofy and regular riders.
1. Depending on the style of riding, place the footstraps over the desired
inserts. One on the front of the board and one on the back.
2. Place the screw through the screw insert and hold the footstrap.
3. Align the holes with the footstrap insert.
4. Screw the footstrap to secure it.
Female
connectors
Battery bottom
Footstraps
inserts
Footstrap insert
Footstrap screw
Screw
insert
Battery magnet
Battery compartment
Insert the magnet and
place the sticker above
it
MAGNET
STICKER

ONEAN X USER’S MANUAL
10
04 Use and ConfigUration of the eqUipment
4. uSe and conFiguration oF the equiPMent
4.1. batterieS
4.1.1. tranSPort and Storage oF batterieS
• In order to travel with the board, the batteries must be below 20% of charge.
This means that the LED bar must be only showing one LED.
Placing the drop near the battery display you will be able to check the
battery level.
• Do not transport the batteries inside the board unless you intend to
use it immediately.
• Between uses you should store the batteries between 0 ºC and 40 ºC (32
°F and 104 °F) always less than 3 months, in a ventilated area and with
a humidity between 0% - 80%. Do not store the batteries near metallic
objects.
4.1.2. connecting/diSconnecting the batterieS
Always charge the batteries and remote to the fullest before operating the
equipment.
Connection and disconnection of the battery:
1. Check the watertight seal and the battery housing to make sure they are
clean and free of sand. Verify there aren´t any signs of damage or water
inside the battery compartment before use.
2. Turn the vent one full round counter-clockwise. Place the battery
on the pad, near the battery compartment where the battery must
be placed. Once the battery is placed
on the pad, grab it by the upper handle
and place in the battery compartment.
The blue LED on the front of the board
will light up indicating the connection.
Drop
Sensor
Charging
indicator
Battery connectors
SYNC BATTERY
VisualizationVisualization Charge%Charge%
20%
40%
60%
80%
100%

ONEAN X USER’S MANUAL 11
04
uSe and conFiguration oF the equiPMent
3. Make sure the four pins are not visible and be aware of the
positioning while inserting it. Only one way is possible according to its
geometry.
4. Once the Battery is inserted in the board, insert
the four pins to lock the Battery. If the pins do
not enter easily, please, press down on the
battery so the watertight seal is sufficiently
compressed.
5. Close the vent completely, turning it clock wise to assure watertightness.
6. In order to ease the extraction of the batteries, turn the vent one full
round counter-clockwise. Pull from the upper handle perpendicularelly
to extract the batteries.
7. Keep the vent always closed in any other moment
and do not turn it more than three full turns.
Battery
Compartment
Board
Connectors
Antenna´s LED

ONEAN X USER’S MANUAL
12
04 Use and ConfigUration of the eqUipment
a) connection
1. In order to charge the battery it must be taken out from the board.
2. Insert the connector to the battery respecting the colours as shown in the
previous drawing (red with red and black with black).
3. When connecting the charger to the battery the LEDs will light up
indicating a successful connection. In case of the LEDs not lighting up,
please make sure that the charger is properly plugged to the wall
outlet and to the battery.
4. Once the battery is connected, the display LED indicator of the charger
will light up indicating the charge (img. A) until fully charging it, turning to
green (img. B).
5. The LEDs in the battery will progressively light up as the battery is being
charged.
6. When the battery is fully charged the LEDs will turn off and
you must proceed to disconnect the battery.
!
Frontal View
AC Cable
DC Cable
Static Yellow light indicates
normal charging
Green LED lights up when battery is
fully charged
¨A¨Charging “B” Full charge
Charging indicator
Connector body
Battery connectors
WARNING!
Always connect the charger to the wall outlet rst and then to the
battery.
It is extremely important to respect the colours when connecting the
cable to the battery. Reverse polarity could have some devastating
consequences for the battery.
4.1.3 battery charge

ONEAN X USER’S MANUAL 13
04
uSe and conFiguration oF the equiPMent
b) diSconnection
Avoid pulling from the cable, always pull
from the connector’s body.
c) iMPortant
Always supervise the charge, do not leave the batteries unattended while
charging.
• The batteries do not need to be fully discharged before charging. A
Lithium Ion battery doesn´t have memory effect. This means that
the maximum energy capacity won´t be aected if it´s charged after not
being fully discharged.
• Make sure that the batteries do not remain connected to the charger
after the charge has been completed.
• Always remember to close the battery rubber connector covers before
use.
• The temperature use for the batteries must always remain between 0 ºC
and 60 ºC (32 ºF y 140 ºF).
• Extreme temperatures will aect the batteries life, especially during
charge. Avoid charging the batteries while being exposed to direct sunlight
or extreme high or low temperatures. The charge is recommended to be
carried out with temperatures (between 10 ºC y 45 ºC / between 50 ºF y
113 ºF).
• Do not overdischarge the batteries. Do not continue riding once the
power starts to decrease and the LEDs on the top bar begin to blink, this
has been proven to decrease the battery’s capacity over time. This is an
extra energy resource which must be used only for emergencies.
4.2. wireLeSS controLLer
To activate the board you must press on the drop. The power of the Jet will
depend on the amount of pressure exerted on the drop.
4.2.1. controLLer conFiguration
Through the wireless controller you can set the maximum power for the Jet
and also adjust dierent proles.
In order to access the configuration menu, you must stick to the following
indications.
1. With the controller totally off (no LEDs ) place the drop over the logo.
SYNC BATTERY
Drop
Sync
Controller
battery
Board Battery
Power
Indicators
SYNC BATTERY
1
Connector’s
body
Cable

ONEAN X USER’S MANUAL
14
04 Use and ConfigUration of the eqUipment
2. On this position, press on the drop
until the first LED of the board display
on the controller begins to blink.
At this moment, the LED bar will
progressively light up. Each position
represents a different function.
a) Synchronization. 1St Led bLinking
Always with the batteries initially disconnected, and once the rst LED
begins to blink, you must press on the drop again to access the submenu.
In this submenu, the controller will start searching for a board for a
few seconds and the sync LED will begin to blink.
As the sync LED is blinking the battery must be inserted to complete
the synchronization (see 4.1.2.).
Once the board is synched, both LEDs will
blink at a higher pace indicating that the
process has been successfully completed.
b) MaXiMuM Power. 2 LedS
bLinking
Once the rst two LEDs start
ashing you must press on the drop to access this submenu.
The power bar will progressively light up. Press on the drop
to set the desired value according to the following description.
c) controLLer SenSitivity. 3 LedS bLinking
Once the rst three LEDs are ashing you must press on the drop to
access the submenu.
The power bar will progressively light up. Press on the drop
to set the desired value according to the following description.
• 1 LED: Staggered 1.
• On this profile we have discretized the power levels of
the jet in 5 different ranges of pressure on the drop. It
allows us to control and hold the pressure on each range.
SYNC BATTERY
LED Blinking
2
SYNC BATTERY
LEDs Power [W] Display
1 LEDs 1.500 W
2 LEDs 2.300 W
3 LEDs 5.100 W
4 LEDs 7.400 W Factory Settings
5 LEDs 10.000 W
Power %
Low
0
20
40
60
80
100
Medium High
Staggered 1

ONEAN X USER’S MANUAL 15
04
uSe and conFiguration oF the equiPMent
• 2 LEDs: Staggered 2. This prole has three power levels. The
rst one allows us to activate the jet at a low potency in order to go at
slow speeds (for example, to go from shore to a safe cruising area). The
second power level will allow us to decrease the power consumption
once planing is reached so we can get more battery life.
• 3 LEDs: Staggered 3. This is a prole similar to the previous
one with the difference that the second power level is at a higher
power. In case that ¨Staggared 2¨doesn´t allow us to reach planing we
could use this one.
• 4 LEDs: 100% / 0%. The jet will from 0 to 100% power
by pressing on the drop. This will be the most comfortable
setting for those wanting maximum power throughout
the ride but the battery life will be compromised.
Power %
Low
0
20
40
60
80
100
Medium High
Staggered 2
Power %
Low
0
20
40
60
80
100
Medium High
Staggered 3
Power %
Low
0
20
40
60
80
100
Medium High
Staggered 4
Power %
Low
0
20
40
60
80
100
Medium High
Staggered 5
• 5 LEDs: lineal. On this profile, the jet reacts
lineally to the pressure on the drop. It requires a bit more of
skills in order to use the entire range appropriately.

ONEAN X USER’S MANUAL
16
04 Use and ConfigUration of the eqUipment
d) reSet. 4 LedS bLinking
3. Once the controller has reached all 4 LEDs, all the
information will be stored and all LEDs will turn o.
If you do not want to change any of these parameters you don’t need
to do this process again, it will remain in the internal memory of the
controller.
4. To check the current status you can repeat step 1 but press on the drop
only one time instead of holding it pressed. The controller will show the
preferences for each category.
5. Always use the controller inside the controller wristband.
6. Always secure the wirstband before use.
7. In order to activate the jet, press on the drop with the index nger and
thumb.
8. The power will vary depending on the pressure placed on the drop.
4.2.2 . charging the controLLer
1. Connect the Qi charger through a USB.
2. Place the controller on the center of the Qi as shown in the drawing
below.
3. When charging, the green LED of the Wireless Controller will begin to
blink.
4. Once the controller is fully charged, the LED will turn o.
5. To check the status of the battery of the controller, please pick it up and
press on the drop to see the battery LED.
SYNC BATTERY

ONEAN X USER’S MANUAL 17
04
uSe and conFiguration oF the equiPMent
4.3. LeaSh
1. Attach the leash right below the knee of the front leg, as shown on the
drawing below.
2. Once the rider is ready to use the board, place the security magnet
key on the board.
The magnetic key is a security mechanism, the jet will not activate if this
key is not properly placed.
3. In case of a fall, the magnetic key will detach, stopping the jet. Once the
rider is back on the board ready to continue its use, the magnetic key
should be properly placed again.
4.4. Security MechaniSMS
The board has various security mechanisms that stop it automatically in case
of:
• Engine overheat.
• Battery overheat.
• Loss of communication between the controller and board.
• Tightening of the jet when starting or blockage of the turbine due to an
external object.
• Magnetic key disconnection. In case of a fall, it will automatically
disconnect the board.
• In case of a fall, or if the controller is submerged, the jet will stop as a
security measure.
• Sound warning system that alerts when the female and male connectors
overheat.
If any of the previous cases happens during use, the jet will automatically
stop. This security block will remain until the above causes are solved.
In order to reactivate the board, the security magnet must be disconnected
and reconnected.
Magnetic Key
Magnetic Key
Connector

ONEAN X USER’S MANUAL
18
05Safety GuidelineS
5. SaFety guideLineS
5.1 terMS oF uSe
• The Onean X board is suitable for fresh and salt water use.Ideal
conditions are with no wind and at water.
• Be aware of local regulations before using and the areas where this
kind of equipment is eligible for use.
• Taking into account that the jet sucks water through the intake it is
important to look for water that is free of oating elements at which
to practice this sport. Floating elements could cause damage to the
rotating components inside the jet.
• The Onean X Board has not been designed to be used at wave breaking
areas. Please look for an area of calm waters to enter the water.
• Taking into account the high speeds and maneuverability of the board,
it’s important to use the Onean X in large open spaces free of obstacles.
• Be aware of the tides. With the sea level changes, new obstacles may
arise depending on the tide.
• Avoid using this product in the vicinity of other people, vessels or objects
that may compromise the user’s or board’s security.
• Avoid crowded beaches and always respect the navigation channels.
• In case of entering the water through the beach, make use of the marked
areas that allow the entry and exit of watercrafts.
• It is advisable not to overturn/ip the board in the water.
• Do not grab or lift the board by the discharge connectors.
• Do not remove the goretex vent in the back of the board.
5.2. beFore getting into the water
• Make sure the leash and the magnetic security key (kill switch) are in good
condition.
• Make sure the remote works properly before heading to the water.
• Make sure to assemble your equipment over grass or sand in order not
to damage it. Any damage caused by manipulating your equipment over
a hard and abrasive surface will not be covered by the warranty.

ONEAN X USER’S MANUAL 19
05
Safety GuidelineS
5.3. FirSt uSe
5.3.1. Start uP
During the rst uses it is recommendable to use it on your knees.
1. Get on top of the board with the leash attached and the magnetic
key connected. You should place your knees on each side of the front
footstrap.
2. After being positioned, press on the drop to activate the jet. The power
will vary depending on the pressure being put on the drop.
3. Once you gain speed you can progressively stand on it.
Make sure not to accidentally press on the drop while getting on or o
the board.
5.3.2. turn
Before turning, make sure there is enough space to do so
and not interfere with the trajectory of any other vehicle.
Shift the weight towards the side where you intend to turn to ease the
movement. The more speed, the easier it will be to turn. The board turns like
a conventional board.
5.4. getting out oF the water
• Do not activate the jet outside of the water. The propulsion system is
not meant to be used outside of the water, this could signicantly damage
the jet.
• After a long use going full thrust, it´s recommendable to wait at least
one minute for the jet not to overheat.
• When the jet reaches high temperatures, an inner fan is automatically
activated for heat dissipation purposes. In order for this process to be
done appropriately, the jet must be in contact with the water.
• It is not recommendable to step on the battery surface. Although
it’s designed to hold weight, when stepping on it, the watertight seal
compresses facilitating water to get in.

ONEAN X USER’S MANUAL
20
05Safety GuidelineS
5.5. generaL Security MeaSureS
• This board could reach high speeds. It is recommendable to use a life
vest and a helmet while operating this product.
• Do not go further o shore than you can return swimming and always
have someone watching from shore. Do not operate this product alone.
• Be aware of climate changes or any other sudden change in the
located area (tides, shallow waters...) Do not use this product during
thunderstorms.
• Do not use this product near swimmers or scuba divers.
• Make sure that the water is deep enough to operate this board, be
aware of coral reefs.
• Do not operate in areas of high current or waves. The Onean X is not
meant to be used to surf waves. In case of being tilted by a wave, the
rider could suer severe damages.
• Do not use it behind another board. In case of doing so, make sure you
have enough space to turn in case the rider ahead falls.