ONFORU BDB55D-3 User manual

Quick Start Guide
LED DUSK TO DAWN
WALL LIGHT
MODEL: BDB55D-3 BDJ55D-3 BDL40D-3
BDI45D-2 BDC80D-3 BDD100D-3

2
COMPONENTS AND STRUCTURE
BDJ55D-3
BDI45D-2 BDC80D-3
BDD100D-3
BDB55D-3
BDL40D-3

SPECIFICATIONS
Model
Input Voltage
CCT
CRI
Power Factor
L
70
B
50
lifetime
Beam Angle
ta
Luminaire Location
BDB55D-3 BDJ55D-3 BDI45D-2 BDC80D-3 BDD100D-3 BDL40D-3
Input Current
Rated Power
Luminous Flux
0.38A
45W
4000lm
0.5A
55W
5500lm
0.5A
55W
5500lm
0.58A
70W
6200lm
0.35A
40W
4000lm
0.83A
100W
9000lm
120°
-20-40°C/-4°F-104°F
SUITABLE FOR WET LOCATIONS
100-120V～60Hz
6500K
≥80
≥0.9
30000hours L
70
B
50
@25°
LED WALL LAMP
3
PARTS LIST
Wire Nuts
QTY: 3 FLong Machine Screw
QTY: 1 GSilicone Gasket QTY: 1 HMachine Screw QTY: 2
Machine Screw
QTY: 3
Expansion Rubber Plug
QTY: 3
EVA Gasket
QTY: 1
Mounting Bracket
QTY: 1
IMachine Screw
QTY: 2

4
SPECIFICATIONS
Model
Weight
Max Projected Area
Max. Lighting Coverage
The testing standard of the product's
luminous flux:Place the three/two lights
on the same horizontal surface for
testing, and the tested luminous flux
is the accurate luminous flux.
Note:
Dimensions（LxHxW）
DIMENSIONS
0.9kg/1.98 lb
0.0214m²/0.23ft²
90m²/968ft²
272x123x121mm/
10.71x4.84x4.76 in
BDB55D-3
0.83kg/1.83 lb
0.0214m²/0.23ft²
90m²/968ft²
270x152x109 mm/
10.63x5.98x4.29 in
BDJ55D-3
1.45 kg/3.2 lb
0.049m²/0.52ft²
160m²/1722ft²
455x182x120 mm/
17.9x7.16x4.72 in
BDD100D-3
0.68 kg/1.5 lb
0.022m²/0.23ft²
60m²/645ft²
279x136x118 mm/
10.98x5.35x4.64 in
BDL40D-3
0.9kg/1.98 lb
0.286m²/0.307ft²
70m²/753ft²
256x140x145 mm/
10.08x5.5x5.7 in
BDI45D-2
Model
Weight
Max Projected Area
Max. Lighting Coverage
Dimensions（LxHxW）
1.2 kg/2.64 lb
0.044m²/0.47ft²
115m²/1237ft²
365x195x118 mm/
14.4x7.67x4.64in
BDC80D-3
1. Cover
2. LED Light Source
3. Lamp Bracket
4. Sensor head
1 2
3
4
W
H
L

PREPARATION
5
Before beginning assembly of product,make sure all parts are present.Compare parts with
parts list.If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time:30-60 minutes.
Product appearance may vary from image shown.
Recommended to be installed on the ground above 2.5m (8.2 ft) and no higher
than 5 m (16.4 ft).
TOOLS REQUIRED（not included）
Flathead
screwdriver
screwdriver Silicone Sealant Eye Protection Pliers Step Ladder
WARNING:
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH
THE APPLICABLE INSTALLATION CODE BY A PERSON
FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF
THE PRODUCT AND THE HAZARDS INVOLVED.
NOTE:
CAUTION:
PLEASE MAKE SURE YOUR WALL SWITCH AND POWER AT
MAIN CIRCUIT BREAKER BOTH ARE OFF.
IF IN DOUBT ABOUT ELECTRICAL INSTALLATION, CONSULT
A LICENSED ELECTRICIAN.

RISK OF SHOCK:
BEFORE BEGINNING INSTALLATION,TURN OFF ELECTRICITY
AT THE CIRCUIT BREAKER BOX OR THE MAIN FUSE BOX.
PREPARATION
6
DO NOT CONNECT THIS LIGHT FIXTURE TO AN UNGROUNDED
ELECTRICAL SYSTEM. ATTACH GROUND FIXTURE WIRE TO
EITHER GREEN GROUND SCREW ON MOUNTING PLATE OR
THE GROUND WIRE IN THE OUTLET BOX.
WARNING:
INSTALLING THIS LIGHT IN AN UNGROUNDED ELECTRICAL
SYSTEM MAY CAUSE THE METAL PARTS OF THE LIGHT TO
CARRY CURRENT IF ANY WIRES OR WIRE CONNECTIONS ARE
DAMAGED OR LOOSE. IN THIS CASE, ANYONE WHO TOUCHES
THE LIGHT WILL RECEIVE AN ELECTRIC SHOCK, RESULTING IN
INJURY OR DEATH.
NOTE:
BE SURE TO USE WIRE NUTS/CONNECTORS RATED FOR
THE CORRECT GAUGE AND NUMBER OF WIRES USED.
MAKE SURE THERE ARE NO EXPOSED WIRE BUNDLES
OUTSIDE THE WIRE NUT/CONNECTOR (IF APPLICABLE).
BE CAREFUL NOT TO DAMAGE OR CUT THE WIRE INSULA-
TION (COVERING) DURING INSTALLATION. DO NOT LET THE
WIRES TOUCH ANY SHARP EDGES.

FOR WET LOCATION, MAKE SURE FILL FULL THE GAP OF EVA GASKET AND MOUNTING
SURFACE WITH SEALING COMPOUND OR SILICON GLUE.
7
INSTALLATION STEPS
D
E
H
BLACK
LIVE WIRE
BLACK
LIVE WIRE
FROM FIXTURE
FROM HOUSE
GREED
GROUND WIRE
GREED
GROUND WIRE
FROM FIXTURE
FROM HOUSE
WHITE
NEUTRAL LINE
WHITE
NEUTRAL LINE
FROM FIXTURE
FROM HOUSE
NOK OK

8
GF
F
The raised part (RA) of the metal plate must be
engaged with the recessed part (RE) of the base,
otherwise it cannot be installed.
Note：
RA RE

TROUBLESHOOTING
LED senses a
movement, the light
does not light up
LED sensor light
illuminates during
the day
Cause RemedyMalfunction
1. The light is not energized
2. Other surrounding light
sources make the light
misjudge it as daytime
The shadows around the
sensor make it mistakenly
think it's night
1. Check power-on status
2. Turn off the nearby lights or
sensor head to other directions
Do not cover the sensor head
LED sensor light
flashing
1. Surrounded by other unstable
light sources shining onto the
induction
2. The light from the lamp itself
is reflected on the sensor
1. Avoid being exposed to such
light sources
2. Follow the instructions in
“LED DUSK TO DAWN WALL
LIGHT – Matters Needing
Attention” to readjust the
light sensor
OPERATION INSTRUCTIONS
9
NOTE:
Sensor head:
Do not cover the sensor head, otherwise it will affect the normal operation of
the lamp.
When the ambient brightness is less than
10~20LUX at night, the light will be on
automatically.
When the ambient brightness is more than
30~60LUX during the day, the light will be
off automatically.
Sensor head

Manufacturer / Hersteller:
ShenZhenShiMengZhiTuoKeJiYouXianGongSi
Address: qianwanyilu1haoAdong201shiqianhaishenganghezuoquShenZhen,Guang
Dong, 518000,CN
[email protected] www.onforuleds.com
69 Aberdeen Avenue, Cambridge CB2 8DL,
United Kingdom | [email protected]
EU REP MDH LIGHTING LTD
Suite 302, 292 Strovolos Avenue, 2048 Strovolos
Nicosia, Cyprus | [email protected]
Made in China
UK REP MDH LIGHTING LTD