Onix AN-8006 User manual

Car Stereo
Car CD/CD-R/CR-RW Compatible/AM/FM 2 Band Radio
Model Number AN-8006
After Sales Support
TEL: [phone] Made in China
INSTRUCTION MANUAL
N13275

After Sales Support TEL: [phone]
1
What your 1year warranty means
Congratulations on choosing to buy a ONIX product.
All products brought to you by ONIX are manufactured to the
highest standards of performance and safety, and, as part of our
philosophy of customer service and satisfaction, are backed by
our comprehensive 1Year Warranty.
We hope you will enjoy using your purchase for many years to
come.
Car Stereo

After Sales Support TEL: [phone]
2
1 What your 1 year warranty means
2 Contents
3 Installation
7 Using the detachable front panel
8 Wiring Diagram
9 Operations
9 Location and Function of Keys
11 Using the Remote Control
13 General Operations
18 Radio Operations
20 CD/MP3 Operations
24 Mixed-Mode CDs Operations
25 SD/MMC Memory Card Play Operations
25 AUX in Operations
26 USB Device Operations
27 Disc Notes
30 Specications
31 Important notes
32 FAQ’s
Contents

After Sales Support TEL: [phone]
3
NOTES:
- Choose the mounting location where the unit will not interfere with
the normal driving function of the driver.
- Before nally installing the unit, connect the wiring temporarily
and make sure it is all connected up properly and the unit and the
system work properly.
- Use only the parts included with the unit to ensure proper installa-
tion. The use of unauthorised parts can cause malfunctions.
- Consult with your nearest dealer if installation requires the drilling of
holes or other modications of the vehicle.
- Install the unit where it does not get in the driver’s way and cannot
injure the passenger if there is a sudden stop, like an emergency
stop.
- If installation angle exceeds 30° from horizontal, the unit might not
give its optimum performance
- Avoid installing the unit where it would be subject to high
temperature, such as from direct sunlight, or from hot air, from
the heater, or where it would be subject to dust, dirt or excessive
vibration.
Din Front/Rear-Mount
This unit can be properly installed either from ‘Front’(conventional
DIN Front-mount) or ‘Rear’ (DIN Rear-mount installation, utilising
threaded screw holes at the sides of the unit chassis).
For details, refer to the following illustrated installation methods.
Take out the screw before installation:
Installation
Before installing the unit,
please remove the two screws.

After Sales Support TEL: [phone]
4
Installation
1. DIN FRONT-MOUNT (Method A)
Installation Opening
This unit can be installed in any dashboard having an opening as
shown below:
Installing the unit:
Be sure you test all connections rst, and then follow these steps to
install the unit.
1. Make sure the ignition is turned o, and then disconnect the cable
from the vehicle battery’s negative (-) terminal.
2. Disconnect the wire harness and the antenna.
3. Press the button on the front panel and remove the control panel
(For details, refer to ‘using the detachable front panel’).
4. Lift the top of the outer trim ring then pull it out to remove it.
5. The two supplied keys release tabs inside the unit’s sleeve so you
can remove it. Insert the keys as far as they will go (with the notches
facing up) into the appropriate slots at the middle left and right
sides of the unit. Then slide the sleeve o the back of the unit.
53mm
182m m
WARNING: This unit must be installed by a professional
technician only or the warranty will be void.

After Sales Support TEL: [phone]
5
6. Mount the sleeve by inserting the sleeve into the opening of the
dashboard and bend open the tabs located around the sleeve with
a screwdriver. Not all tabs will be able to make contact, so examine
which ones will be most eective. Bend open the appropriate tabs
behind the dashboard to secure the sleeve in place.
7. Reconnect the wire harness and the antenna and be careful
not to pinch any wires or cables.
8. Slide the unit into the sleeve until it locks into place.
9. To further secure the unit, use the supplied metal strap to secure
the back of the unit in place. Use the supplied hardware (Hex Nut
(M5mm) and Spring Washer) to attach one end of the strap to the
mounting bolt on the back of the unit. If necessary, bend the metal
strap to t your vehicle’s mounting area. Then use the supplied
hardware (Tapping Screw (5x25mm) and Plain Washer) to attach
the other end of metal strap to a solid metal part of the vehicle
under the dashboard. This strap also helps ensure proper electrical
grounding of the unit.
Install the short threading terminal
of the mounting bolt to the back of
the unit and the other long threading
terminal to the dashboard.
Installation

After Sales Support TEL: [phone]
6
10. Reconnect the cable to the vehicle battery’s negative (-) terminal.
Then replace the outer trim ring and install the unit’s front panel
(see the steps of ‘to install the front panel’).
Removing the unit:
1. Make sure the ignition is turned o, and then disconnect the cable
from the vehicle battery’s negative (-) terminal.
2. Remove the metal strap attached to the back of the unit (if attached).
3. Press the release button to remove the front panel.
4. Lift the top of the outer trim ring then pull it out to remove it.
5. Insert both of the supplied keys into the slots at the middle left and
right sides of the unit then pull the unit out of the dashboard.
2. DIN REAR-MOUNT (Method B)
If your vehicle is a Nissan, Toyota, follow this mounting instruction.
Use the screw holes marked T (Toyota), N (Nissan) located on both
sides of the unit to fasten the unit to
the factory radio mounting brackets
supplied with your vehicle. Fasten the
unit to the factory radio mounting
brackets. Align the screw holes on
the bracket with the screw holes on
the unit, and then tighten the screws
(5x5mm) on each side.
NOTE: The outer trim ring, sleeve
and the metal strap are not used for
method B installation.
Installation

After Sales Support TEL: [phone]
7
Removing and protecting the detachable front panel
The front panel of the unit may be removed as a theft deterrent. After
removing the front panel, use the case provided to keep the front
panel from getting damaged.
1 Press the OPEN button to ip down the front panel.
2 Grasp the right side of the front panel, then gently push the front panel
towards the left side before pulling it out from the unit.
3 Store the front panel in the protective
case provided for safe keeping.
To attach the front panel
Hold the right side of the front panel with the plate facing down.
First attach the left side of the front panel to the unit by inserting the
hole into the left holder.
Then slightly push it leftward and attach the right side hole into the
right holder. Finally push up the front panel.
Open button
front panel
front panel
protective case
1
2
Using The Detachable Front Panel

After Sales Support TEL: [phone]
8
Wiring Diagram

After Sales Support TEL: [phone]
9
Location and function of the keys
Front panel:
Operations
Thefrontfacetafterremovingthefrontpanel:

After Sales Support TEL: [phone]
10
Descriptions of function controls:
1 Power( )/ Mute Button
2 LCD display
3 Encoder Volume Control/ SEL Button
4 Open ( ) Button
5 Disc slot
6 Eject ( ) key
7 SD/MMC Memory Card Slot
8 USB Port
9 MODE Button
10 DISP Button
11 Anti-theft LED Indicator
12 Reset Button
13 Band/ ID3 Button
14 Preset Station (M1-M6) Buttons
15 PS/AS(Preset memory / Scan Auto-storage)
16 UP ( ) Button
Tune up, Seek up, track up, fast forward
17 DOWN ( ) Button
Tune down, Seek down, track down, fast reverse
18 ST Button
19 LOUD(Loudness) Button
20 Scan Button
21 EQ Button
22 Playing/Pausing( ) Button
23 Scan(SCN) Playback Button
24 Repeat(RPT) Playback Button
25 Shue(SHF) Playback Button
26 Skip 10 tracks(-10) Down Button
27 Skip 10 tracks(+10) Up Button
28 AUX Input Jack
29 IR Remote Control Sensor

After Sales Support TEL: [phone]
11
Using the remote control:
Remark:
* Before using the remote control, please take the transparent
insulator slice o the bottom of remote control.
* Point the remote control at the remote sensor within 2 metres.
* It may not be possible to operate the remote control if the remote
control sensor is exposed to direct sunlight.
* Operation angle: about ±30°in each the direction of the front of the
remote sensor.
* The remote control is a small, lightweight precision device.
To avoid damage, short battery life, operational errors and poor
response, observe the following.
- Do not subject the remote control to excessive shock.
- Do not put in a trouser pocket.
- Keep away from food, moisture and dirt.
- Do not place in direct sunshine.
NOTE: Refer to page 10
for key reference.

After Sales Support TEL: [phone]
12
Battery replacement:
Battery type: a button cell lithium battery (CR2025 3V)
1. Remove the battery holder by pressing the locking tab with your
thumb and pulling it out.
2. Replacing the battery:
Replace the battery with the same type and the (+) side facing up.
3. Closing the cover:
Gently push in the holder until it is securely locked into place.

After Sales Support TEL: [phone]
13
Reset the unit:
Operating the unit for the rst time, after replacing the car battery or
changing the connections, you must reset the unit.
1. Turn o the unit power.
2. Press the OPEN ( ) button and remove the front panel, then press
the RESET button with a ballpoint pen to restore the unit to the
original factory settings.
Reset the unit:
In power o mode, switch on the unit by pressing any button except
the OPEN button and the EJECT ( ) button or inserting a disc into
the disc slot. When the system is on, press and hold the POWER ( )
button for several seconds to turn o the unit.
Sound Adjustment:
- Rotate the rotary encoder to adjust volume level.
- Press the SEL button once and/or repeatedly to select the following
sound modes:
Volume, bass, treble, balance and fader.
Press the VOL+ or VOL - button to adjust level of
the selected sound mode:
- VOL: Min,01,02 ~ 44,45,Max
- BAS / TRE: -6, -5 ~,0, ~ +5,+6,
- BAL: 6L,5L, ~,0, ~, 5R, 6R
- FAD: 6R, 5R, ~, 0, ~, 5F, 6F
NOTE: In each mode, when the mode has not been adjusted for 3
seconds, display mode returns to normal radio, DISC, SD/MMC
card, USB or AUX mode.
General operation

After Sales Support TEL: [phone]
14
System menu:
Press the SEL button and hold for more than 2 seconds to access the
system menu mode, then press the SEL momentarily to select the
menu items in series and circulation as follow:
SEEK PRI/STEP RPI DX/LOCAL LOUD ON/OFF VOL LAST/ADJ
P-VOL BEEP ON/OFF.
After selecting the desired menu item, rotate the rotary encoder to
select the mode of the selected item.
SEEK PRI / STEP PRI:
After entering this mode, rotate the rotary encoder to select the SEEK
PRI or STEP PRI.
- SEEK PRI: If you select this mode , the automatic search will be prior
when you briey press the or button.
- STEP PRI: If you select this mode, the manual search will be prior when
you briey press the or button.
STEREO / MONO:
FM listening is received in stereo mode. However, if the signal is weak
or the reception is not as good as you would like, switching to MONO
mode usually improves the overall sound quality.
Rotate the rotary encoder to choose FM STEREO or MONO audio
eect.
LOCAL / DX:
In urban settings, most stations are strong enough and it should
be set in local mode. However, if a station has weaker signals, try
switching to distant(DX) mode. After entering this mode, rotate the
rotary encoder to local reception mode.

After Sales Support TEL: [phone]
15
LOUD ON / OFF:
This function is used to enhance the intensity of bass, after entering
this mode,rotate the rotary encoder to choose loudness on or o.
VOL LAST/ADJUST:
Rotate the rotary encoder to choose between VOL LAST and VOL ADJ.
- VOL LAST: The unit switches on at the last volume level when it was
last switched o.
- VOL ADJ: This function allows you to set the switch-on volume level,
regardless of what level the volume was set at when the
unit was switched o.
PVOL:
To set the volume to a certain level, press the SEL button momentarily
until “PVOL” is shown on the LCD display. Then rotate the rotary
encoder to adjust to a certain volume level.
BEEP ON / OFF:
The car audio device is equipped with 2 beep tone on, beep tone o
function. After entering this mode by pressing the button, rotate the
rotary encoder to choose one.
- Beep on mode: The conrmation beep is heard whenever
a button is pressed.
- Beep o mode: The conrmation beep is switched o when
a key is pressed.
MUTE ON / OFF:
In power on mode, press the POWER ( )/ MUTE button briey to
toggle mute on or o. The muted state will also be released when the
rotary encoder, MODE button is used.

After Sales Support TEL: [phone]
16
LOUD ON / OFF:
Press the LOUD button to enhance the intensity of bass. Press again to
cancel the loudness eect.
To select EQ mode:
The car audio device is equipped with 4 preset equalization modes.
Press the EQ button repeatedly to select the EQ modes as follow: DSP
OFF CLASSIC ROCK POP FLAT .
To select playback mode:
In power on mode, press the MODE button repeatedly to select the
dierent modes as the following sequence: TUNER, DISC (with a CD/
MP3 disc inside the disc slot), USB, SD/MMC memory card, AUX mode.
To select the audio auxiliary input mode:
During TUNER, DISC, USB or SD/MMC memory card playback mode,
press the AUX button to switch to audio auxiliary input mode. Press
again to exit and resume original playback mode.
Last position memory feature:
- During disc, USB, SD/MMC card playback, if you turn o the unit and
then switch it on, the unit will resume playing from the point that it
was interrupted.
-During disc, USB, SD/MMC card playback, if you switch to other
modes, and then return to the previous mode again, the unit will
resume playing from the point that it was interrupted.

After Sales Support TEL: [phone]
17
Clock display and adjustment:
To view the current time, press the DISP button briey, it will be
shown for about 5 seconds and then revert to the previous display
mode unless the DISP button is pressed again. During the period
when the time is shown on the LCD display, you can adjust the clock
time, press and hold the DISP button, the hour will twinkle, rotate the
rotary encoder on the head unit or press the VOL UP or VOL DOWN
button to adjust hour. Then press the DISP button, the minute will
twinkle, then you can adjust minute by rotating the rotary encoder or
pressing the VOL UP or VOL DOWN button.
TEL MUTE:
The audio system automatically mutes whenever a call comes in.
NOTE: The function will not work if a cable is not connected
to the car phone.
1. When a call is received,‘TEL CALL’ is displayed and all the unit
functions are temporarily interrupted.
2. Hang up the phone the ‘TEL CALL’disappears from the display.
The original source is returned to automatically and the volume
restored gradually.
ESP Function:
This unit has the electronic shockproof function. it can be shockproof
for several seconds:
CD: 40 seconds.
MP3/WMA:120 seconds.
Anti-theft LED Indicator:
Designed as a theft deterrent, the red LED will ash when the unit is
turned o and the face plate is removed.

After Sales Support TEL: [phone]
18
To select a radio band:
In tuner mode, press the BAND button repeatedly to select a radio
broadcasting band you would like to hear. The FM band is toggled
cyclically through the tuning bands: ->FM 1-> FM 2 -> FM 3 ->MW 1
-> MW 2.
Auto / Manual tuning:
1. When you select the SEEK PRI in the system setup menu:
- Automatic search mode:
Briey press the or button, the auto search will start. It will
search upward or downward for the strongest signal radio stations
within the current band. During auto tuning press the or
button to stop tuning. Pressing and holding the or button for
about 2 seconds until “MANUMODE” appears on LCD display, it will
change into manual search mode.
- Manual search mode:
Press the or button once and/or repeatedly to manually search
upward or downward step by step for the desired radio station within
the current band. In manual search process, if both buttons haven’t
been pressed within 5 seconds, it will change into automatic search
mode automatically, “SEEK MODE”will be visible on the LCD display.
2. When you select the STEP PRI in the system setup menu:
Press the or button to manually search upward or downward
step by step for the desired radio station within the current band.
Press and hold the or button and the auto search will start.
It will search upward or downward for the strongest signal radio
stations within the current band. During auto tuning press the or
button to stop tuning.
Radio Operations

After Sales Support TEL: [phone]
19
To store / recall a preset radio stations:
You can store up to a total of 18 FM and 12 MW radio stations in the
memory, manually or automatically.
To store a station:
- Select a band (if needed).
- Select a station by pressing the or buttons.
- Hold a preset button (M1~M6) which you want to store the station
for at least 2 seconds, the current station will be saved into the
relevant preset memory bank.
To recall a station:
- Select a band (if need).
- Press a preset button (M1-M6) briey to recall the stored station.
Auto store / Preset scan:
- Preset scan:
Short pressing the PS / AS button, it scans each preset stations in the
memories of the current band. Each preset station will blink for 5 seconds
with releasing mute, then go to next station, nally the radio will go to
play the start preset station. Press again to stop preset scanning.
- Auto store:
Pressing the PS / AS button for more than 2 seconds, it will enter auto
store mode. The whole band is scanned and the six strongest stations
are stored into the preset memories, after scanning is nished.
Scan function:
Press the SCAN button briey, the tuner starts scanning. When the
tuner detects a good station, it pauses for about 5 seconds after that
continues to scan. Press any function key to stop the scanning.