Optoma 3 Series User manual

MOBILE TROLLEY
ST01
User guide - Optoma 3-Series IFP setup and installation
The xed mobile trolley allows you to easily transport your display between locations.
optoma.com

English
1
SETUP AND INSTALLATION
Wall Mounting Installation
Use only an Optoma-approved optional wall mount kit (available separately). Kit will include the following items:
Screw A(x4) Screw B(x8) Screw C(x2)
Dual mounting brackets and wall mount Anchor (x8) Washer (x8)
Wall Mount Specications
Model Name VESA Grid Screw Type & Length
65-inch 600 x 400 mm M8*25L
75-inch 800 x 400 mm M8*25L
86-inch 800 x 400 mm M8*25L
65-inch 75-inch
M8 M8
M8
M8
237.7
400305.8
473.2 600 473.2
485.1 800 485.1
309.1
400
362.2
209.1
262.2
600
M8
M8 M8
M8
609.7 800 609.7
380.1400
432.3
229.8
282.6
700
M8
M8 M8
M8
86-inch

English 2
SETUP AND INSTALLATION
To mount the IFP on the wall, complete the following steps:
1. Install the dual mounting brackets on the rear of the IFP. Then secure the brackets with four
screws (A).
A
2. Drill eight small holes on the mounting location and insert the anchors into the holes.
3. Position the wall mount on the wall, then secure the wall mount with eight screws (B) through the
washers into the installed anchors on the wall.
B

English
3
SETUP AND INSTALLATION
4. Align and hook the dual mounting brackets to the wall mount.
5. Secure the dual mounting brackets and the wall mount with two screws (C).
C
Note:
•
•
•
•
The maximum wall mount kit load capacity:160kg (352lbs).
Please ensure that the wall mount is installed on a wall that can bear the weight of the IFP. If an
appropriate wall is not available, we recommend using a stand instead. Please refer to page 5. Screws
must be tightly secured; however, to avoid damage to the mounting brackets, wall mount, or IFP, do
not overtighten the screws.
The installation should only be performed by qualied technicians. Improper installation may cause the
IFP to fall or malfunction.

English 4
SETUP AND INSTALLATION
Installing an External Mini Computer
Install the mini PC bracket on the rear side of the IFP, then complete one of the following to install the mini
computer:
• Install the screws onto the mini computer, then align and hook the mini computer to the mini PC bracket.
• Align and install the mini computer to the mini PC bracket. Then secure it with four screws.

English
5
SETUP AND INSTALLATION
Stand Mounting Installation (Optional)
The stand mount kit includes the following items:
Pen tray (x1) Wheel (x4) Screw J(x16) Screw H(x4)
Nut G(x4) Washer G1 (x4) Split Ring Lock
Washer G2 (x4)
Stand pole (x2) Stand base (x1) Screw K(x4) Washer K1 (x4) Nut K2 (x4)
To mount the IFP on the stand, complete the following steps:
1. Install the dual mounting brackets on the rear of the IFP. Then secure the brackets with four
screws (A).
A
Note: Dual mounting brackets, wall mount, and screws (A)are included in the wall mount kit. Refer to
“Wall Mounting Installation” on page 1.

English 6
SETUP AND INSTALLATION
2. Flip the stand base so that you can see the screw holes for the wheel, then install the wheel onto its
slot and secure it with four screws (J).
Repeat the same procedure to install the remaining three wheels.
J
3. Place the stand base on the stable surface, then install the stand pole onto its slot and secure both
standoffs with two nuts (G) through the washers (G2 and G1).
Repeat the same procedure to install another stand pole.
G
G2
G1

English
7
SETUP AND INSTALLATION
4.
5.
Align the pen tray with the screw
holes on the middle part of the poles,
then secure the pen tray with four
screws (H).
Install the wall mount on the upper
part of the poles, then insert the
screws (K) through the screw holes
from the rear side of the poles. *
6. Place the washers (K1)and the nuts
(K2) into the screws, then tighten the
nuts (K2) to secure the wall mount in
place.
7. Align and hook the dual mounting brackets to the installed wall mount on the stand poles.
H
K
K1
K2
* Please Note:
a) For safest use and to avoid risk
of tipping, do not mount at
highest point on ST01 stand.
b) Do NOT stand underneath ST01
stand when adjusting mount
height
Please Note:
•Do not operate or place the ST01
stand on a sloped surface as this
can cause rolling and/or result in
injury or harm to self and others.