HumanCentric 101-2018 User manual

Model 101-2018
ADDITIONAL TOOLS REQUIRED
Under-Desk and Wall Mount for CPU / Computer Case
www.humancentric.com/patents
PARTS INCLUDED
© 2017 HumanCentric Ventures LLC www.humancentric.com
Phillips Head Screwdriver
Flat Head Screwdriver
Adjustable Wrench
Note: Not all parts will be used in the installation. Multiple configuration options are provided to fit dierent
TVs, and dierent parts are used for dierent configurations.
A Computer Case Holder
COMPATIBILITY INFORMATION
Weight capacity:
10kg (22lbs)
Maximum Dimensions:
Width: 3.5” to 8” (88mm to 203mm)
Height 12” to 21” (300mm to 533mm)
Power drill with ¼” (wood stud) or ⅛” (concrete wall or block) drill bit
Level
Marking Pencil
For wall mounting :
F Washers (4)
GAllen Wrench
E Felt pads (12)
DPlastic wall anchors (4)
B st4.8 (#10) x 16mm Self-Tapping Screw (4)
Cst4.8 (#10) x 38mm Self-Tapping Screw (4)
Read the entire instruction manual, including the warnings at the end of the manual, before you start installation and assembly.
If you have any questions regarding any of the instructions or warnings, please contact the HumanCentric support team for
assistance at [email protected]
CAUTION
Use with products heavier than the maximum weights indicated may result in damage to the mounted devices or
personal injury.
IMPORTANT
Ensure that you have received all parts according to the parts list prior to installation. If any parts are missing or
damaged, please contact the HumanCentric support team for replacements at [email protected]
1

© 2017 HumanCentric Ventures LLC www.humancentric.com
Apply the 12 felt pads to the mount in
the positions shown below.
1. APPLY FELT PADS TO MOUNT
2. ADJUST MOUNT TO FIT COMPUTER
Set the mount on the floor, lying on its side.
Remove the vertical adjustment lock knob
and loosen the adjustment peg with the
allen wrench. Then slide the lower end to
the fully extended position.
Extend the horizontal adjustment arm to
allow your computer to fit inside the case. If
you reach the full length and it is not wide
enough, move the
adjustment screw
from position A to
position B. AB
left side
right side
1
2
2

© 2017 HumanCentric Ventures LLC www.humancentric.com
2. ADJUST MOUNT TO FIT COMPUTER
Place your computer
inside the case and
make the vertical
adjustment as tight as
possible (there may be
a small gap between
the top of the
computer and the
case).
3. ATTACH MOUNT
Replace the adjustment lock
knob and tighten the
adjustment peg to lock the
vertical adjustment in place.
Option 1: Attach Mount Under Desk
Use the self-tapping screws (B) and washers (F) to
attach the mount to the bottom of a desk.
Place the computer in the mount and
slide the horizontal grip into place.
Tighten securely on both sides
left side
right side
3

Any questions? Contact us at [email protected], and we’re happy to help!
WARNINGS
The wall must be capable of supporting five times the weight of the device (such as a TV) and mount combined
Mounts must be attached as specified in the instruction manual. Improper installation may result in damage or serious personal injury.
Safety gear and proper tools must be used. This product should only be installed by those with the necessary skills to install the
hardware. If you do not have the necessary skills, installation should be handled by a professional.
Use the mounting screws provided and do not over-tighten the mounting screws
This product contains small items that can be a choking hazard if swallowed. Keep these items away from children.
Do not use this product for any purpose not explicitly specified by manufacturer
This product is intended for indoor use only. Using this product outdoors could lead to product failure or personal injury.
Manufacturer is not responsible for damage or injury caused by incorrect assembly or use.
Check that the mount is secure and safe to use at regular intervals (at least every three months).
HumanCentric intends to make this manual accurate and complete. However, HumanCentric makes no claim that the information
contained herein covers all details, conditions, or variations. Nor does it provide for every possible contingency in connection with the
installation or use of this product. The information contained in this document is subject to change without notice or obligation of any kind.
HumanCentric makes no representation of warranty, expressed or implied, regarding the information contained herein. HumanCentric
assumes no responsibility for accuracy, completeness or suciency of the information contained in this document.
Option 2: Attach Mount To Wall
Extend vertical adjustment
until all four holes are visible,
and hold mount up to wall in
desired location. Check
placement with a level, and
then mark each hole with a
marking pencil.
3. ATTACH MOUNT
35mm
Wooden Walls
and Surfaces
15mm
Concrete Walls
(use wall anchors)
3mm
Insert the top two screws, leaving
3mm of thread length exposed to
hang the mount.
Hang the mount on the top two screws. Then
tighten all four screws to secure the mount in place.
Wooden Walls and
Surfaces
Concrete Walls (use
wall anchors)
© 2017 HumanCentric Ventures LLC www.humancentric.com
Use the drill to make the appropriate
holes for your application:
Use a 1/8” (3.5mm) drill bit to make four
0.6” (15mm) deep holes in the wall.
Use a 1/4” (6mm) drill bit to make four
1.2” (35mm) deep holes in the wall.
4